wheel bolts Citroen BERLINGO 2005 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 156
ENGINE
B1BP2LSC
B1BP2LTC
AUXILIARY EQUIPMENT DRIVE BELT
Engines: KFU - NFU
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument (SEEM) : 4122 -T
[3]Compression lever for dynamic tensioner: (-).0194.D
[4] Peg for dynamic tensioner roller of Ø 4 mm : (-) 0194.F
WARNING: (With or without air conditioning)
The auxiliaries drive belt cannot be re-used
with a manual tensioner roller.
The auxiliaries drive belt can be re-usedwith a dynamic tensioner roller.
Removing.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.
Remove the front RH wheel and the front RH splash-shield, using tool [1].
V
ehicle without air conditioning.Slacken bolts (2), screw (3)and the tensioning screw (1).
Push back the alternator towards the engine.
Remove the auxiliary equipment drive belt.
Refitting.
Refit the new auxiliary equipment drive belt.
Respect the following sequence: Crankshaft pinion, alternator pulley.
Position tool [2]on the belt.
Tighten the screw (1)to tension the belt to: 120 ± 4 SEEM units.
Tighten screw (3), bolts (2).
Remove tool [2].
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 156

Downloaded from www.Manualslib.com manuals search engine 163
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFN
Without air conditioning
Removing.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel, the plastic pins and the splash-shield.
Detension the belt (3)by turning the tensioner roller (1)by means of the
screw (2)
(clockwise).
NOTE:Screw (2)has a left hand thread.
Compress the tensioner roller (1).
Remove the auxiliaries drive belt (3).
IMPERATIVE: Check that the rollers (4) and (5) turn freely
(without play
and without tight spots).
Refitting.
Compress the tensioner roller (1).
Fit the auxiliaries drive belt (3).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly
positioned in the grooves of the various pulleys.
Complete the refitting.
Tightening torques:
- Tensioner roller screw (4) : 2 ± 0,2 m.daN.
- Guide roller screw (5) : 3,5 ± 0,,3 m.daN.
- Wheel bolts: 9 ± 1 m.daN.
B1BP23PCB1BP23QCB1BP23RC
With air conditioning
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 163

Downloaded from www.Manualslib.com manuals search engine 264
ENGINECHECKING AND SETTING THE VALVE TIMING
Tools.
[1]Belt tension measuring equipment : 4122-T
[2]Tension lever: (-).0188.J2
[3]Engine flywheel peg: (-).0188.Y
[4] Belt clamp: (-).0188.AD
[5]Camshaft pulley peg: (-).0188.M
[6] Engine flywheel lock: (-).0188.F
[7] Set of blocking plugs: (-).0188.T
[8] Pulley extractor: (-).0188.P
[9] 2 mm Øpeg: (-).0188.Q2Removing.
IMPERATIVE: Respect the safety and cleanliness requirements
that are specific to high pressure diesel injection (HDi) engines.
Undo the front RH wheel bolts.
Raise and support the vehicle on the front RH side.
Disconnect the battery negative terminal.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield.
- The engine cover.
Unclip and move aside the cooling hose.
Remove the accessories drive belt
(see corresponding operation).
XSARA - XSARA PICASSO
Engines: RHY - RHZ
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 264

Downloaded from www.Manualslib.com manuals search engine 273
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: RHR
Tools.
[1]Kit of plugs: (-).0188.T
[2]Double flywheel setting peg: (-).0188.X
[3]Camshaft setting peg: (-).0188.M
[4]Belt clamp: (-).0188.AD
[5]Pinion centrer: (-).0188.AH
[6]Flywheel lock: (-).0188.F
[7]Pulley(-).0188.P
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel injection (HDi) engine versions.
Removing.
Slacken the front RH wheel bolts.
Raise and support the front RH side of the vehicle.
Disconnect the negative terminal of the battery.
Remove:
- The under-engine sound-deadening.
- The front RH wheel.
- The front RH splash-shield.
- The engine cover.
Remove the auxiliaries drive belt
(see corresponding operation).
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 273

Downloaded from www.Manualslib.com manuals search engine 360
CLUTCH
GEARBOX
TRANSMISSION
DRIVESHAFTS - GEARBOX
Tightening torques (m.daN)Gearbox oil seal mandrels
Vehicles GearboxDriveshaft Driveshaft
Engines
bearing nutRH side LH side Toolkit
C4
MA/5ET3J4 TU5JP4
XSARA TU3JP TU5JP4
C4EW10/DV6 7114-T.W 7114-T.X 7116-T
BE4/5All types
XSARA EW7/10J4B DW8
XSARA PICASSO DV6/DW10
C4ML6 DW10BTED4 9017-T.C 5701-T.A 9017-T
TU5JP4 EW10A 2 ± 0,2 32,5 ± 2,6
(-) 0338 J1 (-) 0338 H1
XSARATU5JP EW10J4
+ (-) 0338 J3 (-) 0338 H2
DW10ATED
AL4Seal extractor
RH / LH(-). 0338
XSARA PICASSO EW10J4 (-) 0338 C
(-) 0338 J1 (-) 0338 H1
+ (-) 0338 J3 (-) 0338 H2
Tightening torque (m.daN) for wheel bolts.
C4 = 9 ± 1 XSARA = 8,5 ± 0,8 XSARA PICASSO = 10 ± 1
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 360

Downloaded from www.Manualslib.com manuals search engine 361
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
Conditions for checking and adjusting
Vehicle heights at reference height
Rear height Front height
L2 L1
Tools : [1] Gauge for measuring the the wheel radius, 4 bolts: 4300-T.
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point
(see corresponding operation).
H1 = R1 - L1
H1 = Measurement between the measuring zone underneath the front
subframe and the ground.
R1 = Front wheel radius under load.
L1 =Distance between the wheel axis and the measuring zone underneath
the front subframe.H2 = R2 + L2
H2 = Measurement between the measuring zone underneath the rear sill
and the ground.
R2 =Rear wheel radius under load.
L2 =Distance between the wheel axis and the measuring zone underneath
the rear sill.
E1AP0F3D
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 361

Downloaded from www.Manualslib.com manuals search engine AXLE GEOMETRY
B3CP097D
Measuring front height Measuring rear height
[1]Gauge for measuring the the wheel radius, 4 bolts: 4300-T
Z1= Measuring zone underneath the front subframe.Z2= Measuring zone underneath the rear sill.
Measure the radius of the front wheel R1 - Calculate dimension H1 = R1–L1Measure the radius of the rear wheel R2 - Calculate dimension H2 = R2+ 2
Value at reference All types
CRD vehicles (*)Value at reference All types (except entreprise CRD
height (except CRD) (*) height entreprise et CRD) (*) vehicles vehicle (*)
(+ 10 - 8 mm) L1 = 144 mm L1 = 124 mm (+ 12 - 10 mm) L2 = 68 mm L2 = 48 mm L2 = 88 mm
(*) = CRD: Difficult road conditions: definition for a type of vehicle with axles and suspension designed for driving on rough roads.
Compress the suspension to obtain the calculated values.
The height difference between the two axle dimensions should be less than 10 mm.
362
AXLES
SUSPENSION
STEERING
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 362

Downloaded from www.Manualslib.com manuals search engine 376
AXLES
SUSPENSION
STEERING
Setting at reference height
Front axle Rear axle
Measure the dimension «R1». Calculate the dimension H1 = R1 - L1. Measure the dimension «R2». Calculate the dimension H2 = R2 + L2.
All types (except CRD version) CRD versionAll types (except Estates
and CRD version) Estates CRD version
90,5 mm 75,5 mm 83 mm 88 mm 103 mm
Compress the suspension to obtain the values (H1)and (H2).
NOTE:The difference in height between the two sides should be less than 10 mm.
AXLE GEOMETRY
Reference heights - RPO 8667 #
Tools [1] Gauge for measuring the radius of wheels with 4 bolts: 4300-T0
XSARA
B3CP04AD
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 376