clutch Citroen BERLINGO 2017 2.G Owner's Manual

49
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
MANUAL GEARBO x
5-speed
6-speed
To change gear easily, always depress
the
 
clutch
 
pedal   fully.
To prevent the mat from becoming
caught
 
under
 
the   pedal:
-

ensure that the mat is positioned
and

 
secured   correctly   on   the   floor,
-
 
never

 
fit
 
one   mat   on   top   of   another.
When driving, avoid leaving your hand
on
 
the
 
gear
 
knob   as   the   force   exerted,  
even if slight, may wear the internal
components

 
of
  the   gearbox   over   time.
Changing into 5th or 6th gear
To engage the gear correctly, move the
gear  lever   fully   to   the   right.
Engaging reverse gear
The lever should be moved slowly
to  reduce   noise.
To engage reverse gear, wait until the
vehicle
  has   come   to   a   complete   stop.
STEERING WHEEL ADJUSTMENT
When the vehicle is stationary,
release
  the   steering   wheel   adjustment  
mechanism

  by   pulling   the   lever.
Adjust
  the   steering   wheel   for   height  
and

  reach,   then   lock   the   mechanism   by  
pushing

  the   lever   fully   forward. In
  the   6-speed   configuration,   raise   the  collar
  below   the   gear   knob.
READY TO GO
3
Gearbox and steering wheel

53
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
STOP & START
The Stop & Start system puts the
engine temporarily on standby - ST OP
mode
  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).
The engine restarts automatically -
START mode - as soon as you want to
move
  off.
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system reduces fuel consumption and
exhaust emissions as well as the noise
level
  when   stationary.
Operation
Going into engine STOP modeThe "ECO" warning lamp
comes on in the instrument
panel and the engine goes
into
  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with a 6-speed electronic
gearbox

, at speeds below 5 mph
(8
  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a time counter calculates the sum of
the periods in ST

OP mode during a
journey.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With a 6-speed electronic
gearbox, for your comfort during
parking   manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP mode does not affect the
functionality of the vehicle, such as
braking,   power   steering,   for   example.
Never refuel with the engine in
STOP mode; you must switch off
the   ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 

mode   is   not   invoked   when:
-
the vehicle is on a steep slope
(rising or fallin

g),
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded

6   mph   (10   km/h)   since   the   last  
engine

  start   using   the   key,
-
the engine is needed to maintain
a comfortable temperature in the
passenger compartment,
-

demisting is on,
-

some special conditions (battery
charge, engine temperature,
braking

  assistance,   ambient  temperature...)
  where   the   engine  is needed to assure control of a
system.
In this case, the
"ECO"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
READY TO GO
3
Stop & Start

54
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Going into engine START modeThe "ECO" warning lamp
goes
  off   and   the   engine   starts:
-

with a manual gearbox
, when you
fully depress the clutch pedal,
-

with a 6-speed electronic
gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position   N and
the
  brake   pedal   released,   when  
you move the gear lever to
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With a manual gearbox in STOP
mode, if a gear is engaged without
fully depressing the clutch pedal, a
warning lamp comes on or a message
is
  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.
Special cases: START invoked
automatically
For your safety and comfort, START is
invoked
  automatically   when:
-

you open the driver's door
,
-

you unfasten the driver's seat belt, In this case the

"ECO"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
This operation is perfectly normal.
Deactivation
In certain circumstances, such as the need
to maintain a comfortable temperature in
the passenger compartment, it may be
preferable
  to   deactivate   Stop   &   Start.
At any time, press the "ECO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp coming on accompanied by a
message

  in   the   screen.
If the system has been deactivated
in STOP mode, the engine restarts
immediately.
Reactivation
Press the "ECO OFF" switch again.
The system is active again; this is
confirmed
  by   the   switch   warning  
lamp going of

f and a message in the
instrument
  panel.
The system is reactivated
automatically at every new start
using
  the   key.
Operating fault
In the event of a malfunction
with the system, the "ECO
OFF" switch warning lamp
flashes,  then   comes   on  
continuously

.
This
  system   requires   a   specific  
battery

  with   a   special   specification  
and technology (reference
numbers available from a CITROËN
dealer

 
or
  a   qualified   workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
have
 
it
 
checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop.
In the event of a fault in STOP mode,
the
 
vehicle   may   stall.  
All
  of   the   warning  
lamps in the instrument panel come
on.

 
It
 
is
 
then   necessary   to   switch   off  
the ignition and start the engine again
using

 
the
  key.
-

the speed of the vehicle exceeds
15

 
mph
 
(25
 
km/h)
 
with
 
a
 
manual
 
gearbox

 
or
 
7
 
mph
 
(11
 
km/h)
 
with
 
the 6-speed electronic gearbox
system,
-
some special conditions (battery


charge,
 
engine
 
temperature,
 
braking
 assistance,

 
ambient
 
temperature...)
 where the engine is needed to


assure
 
control
 
of
 
a
 
system.
Stop & Start

56
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Starting and switching off
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
HILL START ASSIST
This system (also called HHC - Hill
Holder
  Control),   linked   to   the   dynamic  
stability

  control   system,   makes   hill  
starts easier and is activated in the
following

  conditions:
-

the vehicle must be stationary
,
engine
  running,   foot   on   the   brake,
-

the gradient of the road must be
steeper than 5%,
-


uphill, the gearbox must be in
neutral or in a gear other than
reverse,
-


downhill, reverse gear must be
engaged.
The Hill Start

Assist system is a driving
aid.
  It   is   not   an   automatic   vehicle  
parking

  function   or   an   automatic  
parking

  brake.
Operation
With the brake pedal and clutch pedal pressed, from the time you release
the  brake   pedal,   without   using   the  
parking

  brake,   you   have   approximately  
2

seconds to move off before the
vehicle
  starts   to   roll   back.
During the moving off phase, the
function is deactivated automatically,
gradually
  releasing   the   braking  
pressure.

  During   this   phase,   the  
characteristic noise of mechanical
release

  of   the   brakes   may   be   heard,  
indicating the imminent movement of
the

  vehicle.
Operating fault
Hill start assist is deactivated in the
following   situations:
-

when the clutch pedal is released,
-

 
when
  the   parking   brake   is   applied,
-

when the engine is switched of
f,
-
 
when
  the   engine   stalls.
If a malfunction of the
system occurs, this
warning lamp comes on
accompanied by an audible
signal
  and   confirmed   by  
a

  message   in   the   screen.   Have   the  
system

  checked   by   a   CITROËN   dealer  
or

  a   qualified   workshop.

65
Berlingo2VP_en_Chap04_Ergonomie_ed02-2016
Selecting the functionFirst activation /
Programming a
speed Temporarily exceeding the
speed setting
Deactivation (off)
- Press this button or
the  brake   or   clutch  
pedal.
Reactivation
- Following deactivation of the cruise
control,  press   this   button.
Your vehicle will return to the last
programmed
  speed.
Alternatively,
  you   can   repeat   the   "first  
activation"

  procedure.
It is possible to accelerate and drive
momentarily at a speed greater than
the
 
programmed
 
speed
 
setting.
 
The

 
value

 
programmed
 
flashes.
When the accelerator pedal is
released, the vehicle will return to the
programmed
 
speed.
-

Reach the chosen speed by
pressing

 
the
 
accelerator.
-

Press the

SET - or SET +
 
button.
This
 
programmes/activates
 
the
 
speed
 
setting and the vehicle will maintain
this

 
speed.
-

Place the switch in the

CRUISE
position.
 
The

 
cruise
 
control
 
is
 
selected but is not yet active and
no

 
speed
 
has
 
been
 
programmed.
Steering mounted controls
EASE OF USE and COMFORT
4

123
Berlingo2VP_en_Chap05_Securite_ed02-2016
Driving safely
Operation
When your vehicle is too close to or
approaches the vehicle ahead too
quickly  the   system   automatically  
applies

  the   brakes   to   avoid   a   collision.
You are then alerted by the display of a
message.
The
  brake   lamps   on   your   vehicle   come  
on

  to   warn   other   road   users.
The collision can be avoided
automatically if the difference in
speed
between your vehicle and the
vehicle ahead does not exceed 9 mph
(15
  km/h).
Above this threshold, the system will
do what is possible to avoid or reduce
the accident by lowering the speed of
impact.
The
  automatic   braking   may   bring  
the vehicle to a complete stop if the
situation

  requires   it.
In this case, the vehicle is held
stationary temporarily (for about
1.5 seconds)
  to   allow   the   driver   to   take  
back

  control   by   pressing   the   brake  
pedal. The triggering of the system may
cause the engine to stall, unless
the driver depresses the clutch
pedal

  quickly   enough   during   automatic  
braking.
During

  automatic   braking,   the  
driver can always obtain a higher
rate of deceleration than that
controlled by the system, by pressing
firmly

  on   the   brake   pedal.
After an impact, the system is
automatically
  put   out   of   service:   it  
no

  longer   operates.
You must go to a CITROËN dealer or a
qualified
  workshop   to   have   the   system  
made

  operational   again.
Operating limits
The system only detects vehicles that
are stationary or moving in the same
direction  as   your   vehicle.
It does not detect small vehicles
(bicycles, motorcycles),
pedestrians or animals, nor non-
reflective
  stationary   objects.
The system is not triggered or is
interrupted
  if   the   driver:
-

accelerates strongly
-


or turns the steering wheel
suddenly

  (avoiding   manoeuvre).
In
  difficult   weather   conditions   (very  
heavy

  rain,   snow,   fog,   hail...),  
braking

  distances   increase,   which  
can reduce the ability of the system to
avoid

  a   collision.
The driver must therefore remain
particularly
  vigilant.
Never leave accumulations of
snow
  or   any   object   projecting  
above the bonnet or in front of
the

  roof:   this   might   fall   into   the   field   of  
vision of the sensor and generate a
detection.
SAFETY
5

155
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
PETROL ENGINE
1. Screenwash   fluid   reservoir.
2.  
Fusebox.
3.

 
Engine
  coolant   header   tank.
Battery
  connections:
+
 
Positive
  terminal.
-
 
Negative
  point   (earth).
Take
  care   when   working   under   the   bonnet.
4.  Brake   and   clutch   fluid   reservoir.
5.  
Air
  filter.
6.
 
Engine
  oil   dipstick.7.
 Engine   oil   filler   cap.
8.  
Power
  steering   fluid   reservoir.
CHECKS
7
Under the bonnet

156
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
DIESEL ENGINE
4. Brake   and   clutch   fluid   reservoir.
5.  
Air
  filter.
6.
 
Engine
  oil   dipstick.
7.
 
Engine
  oil   filler   cap. 8.
 Power   steering   fluid   reservoir.
9.
Priming pump
 (except

  BlueHDi   engines).
1.
 Screenwash
 
fluid
 
reservoir.
2.
 
Fusebox.
3.

 
Engine

 
coolant
 
header
 
tank.
Battery
  connections:
+
 
Positive
  terminal.
-
 
Negative
  point   (earth).
Take
 
care
 
when
 
working
 
under
 
the
 
bonnet.
Under the bonnet

190
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Fuses under the bonnet
After opening the bonnet, unclip and tilt
the corresponding box to gain access
to  the   fuses. Fuses
F Amperes
A Allocation
1 20 Engine management
2 15 Horn
3 10 Front and rear wash-wipe pump
4 - Not used
5 15 Engine components
6 10 Steering wheel angle sensor, DSC
7 10Brake
  switch,   clutch   switch
8 25 Starter motor
9 10 Headlamp
  beam   motor,   fleet   management   unit
10 30 Engine components 11 40 Not used
12 30 Wipers
13 40 Built-in systems interface
14 30 Pump
15 10 Right-hand main beam headlamp
16 10 Left-hand main beam headlamp
17 15 Right-hand dipped beam headlamp
18 15 Left-hand dipped beam headlamp
Changing a fuse