key battery Citroen BERLINGO 2017 2.G Owner's Manual

5
Berlingo2VP_en_Chap01_vue-ensemble_ed02-2016
ExTERIOR
Remote control 18-19
Changing the battery ,
reinitialisation

19
Key


18
Starting

55
Hill start assist

56
Central

  locking   /  
unlocking
 
18,
  27
Filler cap, fuel
  tank  
161-162
Fuel cut-of

f, Diesel
priming
163
AdBlue®, topping up 38-39, 164-169
Wiper blades

191
Door mirrors


1
10
Side repeaters

184
Active

 
City
 
Brake
 
122-125
Front lamps, foglamps, direction indicators


58-60, 181-184
Headlamp beam height adjustment

 
60
Changing front bulbs

181-184
Snow

 
cover
 
179
Front doors


21
Sliding side


doors

22-23
Key


18
Opening the bonnet

154
Child

 
lock
 
147
T

owing, lifting

192Towbar, swan neck towball 148-151
Parking
 
sesnsors
 1 15-116
Reversing
 
camera
 
1
17
Rear
 
roof
 
flap
 
26
Emergency control


23
Spare

 
wheel,
 
jack,
 

changing a wheel,
tools
 
173-178
T

emporary puncture
repair
 
kit
 
172
Inflation,

 
pressures
 
201
Modutop

 
roof
 
97-98,
  101
Roof bars

102Rear lamps, direction indicators 58-59
3rd
 
brake
 
lamp
 186
Changing rear

bulbs

181-182, 185-186
Doors, tailgate


23-25
Accessories

152
Dimensions 193-196
Brakes,   pads  
1
14,   157,   159
Emergency
  braking  
1
18
ABS, EBFD

1
18
ASR, DSC

1
19
Grip control

120-121
Active

  City   Brake  
122-125
T

yres, pressures
201
Snow chains


180
T

yre   under-inflation   detection  
4
1-42
Tyre
  under-inflation   detection  
with reinitialisation

43-46
Number plate lamps


186
1
OVERVIEW
Location

19
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Good practice
Take care not to allow the remote control to come into contact with
grease, dust, rain or a damp
environment.
A
 
heavy   object   attached   to   the   key  
(key

  ring,   ...)   weighing   on   the   shaft  
of

  the   key   in   the   switch,   may   cause   a  
malfunction.
REMOTE CONTROL
Reinitialising the remote

control
Following changing of the remote
control battery or disconnection of the
vehicle battery, the remote control may
have
  to   be   reinitialised.
Wait at least one minute before using
the
  remote   control.
Insert
  the   key   in   the   ignition   switch   with  
the

  buttons   (padlocks)   of   the   remote  
control

  facing   you.
Switch
  on   the   ignition.
Press
  the   locking   padlock   for   at  
least

  five   seconds   within   the   next  
ten seconds.
Switch

  off   the   ignition.
Wait at least one minute before using
the
  remote   control.
The
  remote   control   is   now   working  
again.
Use only identical batteries or
batteries of an equivalent type to
those recommended by CITROËN
dealers.
Do not discard the remote control
batteries, they contain metals which
are

 
harmful
 
to
 
the
 
environment.
Deposit them at a CITROËN
dealership, or at an authorised
collection
 
point.
Unfolding / folding
Changing the battery
Battery ref.: CR1620 / 3 volts.
The   "battery   flat"   information   is   given  
by an audible signal, accompanied by
a

  message   in   the   screen.
To replace the battery, unclip the
casing
  using   a   coin   at   the   ring.
If
  the   remote   control   does   not   work  
after the battery has been changed,
reinitialise

  the   remote   control.
There
  is   a   risk   of   damage   if   the  
replacement battery is not the correct
type.If you do not press the button,
you

  may   damage   the   key's  
folding

  mechanism.
Access
READY TO GO
3

23
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Operation in the event
of a battery failure
Front and side passenger doors
In the event of a battery or of the
central  locking   fault,   use   the   lock   to  
lock

  the   doors   mechanically.
-

T
o open the door and get out of the
vehicle,
  pull   the   interior   control.
-
 
T
o   lock   the   door,   insert   the   key   in  
the

  lock,   located   on   the   edge   of   the  
door

, then turn it one eighth of a
turn.
Driver's door
-
 
Insert
  the   key   in   the   lock,   then   turn  
it

  to   the   right   to   lock   or   to   the   left   to  
unlock.
TAILGATE
From inside
(emergency control)
In  the   event   of   a   central   unlocking  
operating

  fault,   this   permits   unlocking  
of

  the   tailgate   from   the   inside.
Insert a small screwdriver in the
opening, between the tailgate and the
floor.
 
T
o   unlock   the   lock,   move   the  
catch

  to   the   left   then   push   the   tailgate.
Opening
From outside
Locking/unlocking  is   by   means   of   the  
remote

  control.
To open, press the control below the
trim
  then   raise   the   tailgate.
A pull strap is available to close the
tailgate
  from   the   high   position.
Guide the closing of the tailgate to the
balance point of its travel then push on
the
  tailgate   to   close   it   fully.
Access
READY TO GO
3

53
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
STOP & START
The Stop & Start system puts the
engine temporarily on standby - ST OP
mode
  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).
The engine restarts automatically -
START mode - as soon as you want to
move
  off.
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system reduces fuel consumption and
exhaust emissions as well as the noise
level
  when   stationary.
Operation
Going into engine STOP modeThe "ECO" warning lamp
comes on in the instrument
panel and the engine goes
into
  standby:
-

with a manual gearbox
, at speeds
below
  12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with a 6-speed electronic
gearbox

, at speeds below 5 mph
(8
  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a time counter calculates the sum of
the periods in ST

OP mode during a
journey.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With a 6-speed electronic
gearbox, for your comfort during
parking   manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP mode does not affect the
functionality of the vehicle, such as
braking,   power   steering,   for   example.
Never refuel with the engine in
STOP mode; you must switch off
the   ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 

mode   is   not   invoked   when:
-
the vehicle is on a steep slope
(rising or fallin

g),
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded

6   mph   (10   km/h)   since   the   last  
engine

  start   using   the   key,
-
the engine is needed to maintain
a comfortable temperature in the
passenger compartment,
-

demisting is on,
-

some special conditions (battery
charge, engine temperature,
braking

  assistance,   ambient  temperature...)
  where   the   engine  is needed to assure control of a
system.
In this case, the
"ECO"
warning
  lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
READY TO GO
3
Stop & Start

54
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Going into engine START modeThe "ECO" warning lamp
goes
  off   and   the   engine   starts:
-

with a manual gearbox
, when you
fully depress the clutch pedal,
-

with a 6-speed electronic
gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position   N and
the
  brake   pedal   released,   when  
you move the gear lever to
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With a manual gearbox in STOP
mode, if a gear is engaged without
fully depressing the clutch pedal, a
warning lamp comes on or a message
is
  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.
Special cases: START invoked
automatically
For your safety and comfort, START is
invoked
  automatically   when:
-

you open the driver's door
,
-

you unfasten the driver's seat belt, In this case the

"ECO"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
This operation is perfectly normal.
Deactivation
In certain circumstances, such as the need
to maintain a comfortable temperature in
the passenger compartment, it may be
preferable
  to   deactivate   Stop   &   Start.
At any time, press the "ECO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp coming on accompanied by a
message

  in   the   screen.
If the system has been deactivated
in STOP mode, the engine restarts
immediately.
Reactivation
Press the "ECO OFF" switch again.
The system is active again; this is
confirmed
  by   the   switch   warning  
lamp going of

f and a message in the
instrument
  panel.
The system is reactivated
automatically at every new start
using
  the   key.
Operating fault
In the event of a malfunction
with the system, the "ECO
OFF" switch warning lamp
flashes,  then   comes   on  
continuously

.
This
  system   requires   a   specific  
battery

  with   a   special   specification  
and technology (reference
numbers available from a CITROËN
dealer

 
or
  a   qualified   workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
have
 
it
 
checked   by   a   CITROËN   dealer  
or

 
a
 
qualified   workshop.
In the event of a fault in STOP mode,
the
 
vehicle   may   stall.  
All
  of   the   warning  
lamps in the instrument panel come
on.

 
It
 
is
 
then   necessary   to   switch   off  
the ignition and start the engine again
using

 
the
  key.
-

the speed of the vehicle exceeds
15

 
mph
 
(25
 
km/h)
 
with
 
a
 
manual
 
gearbox

 
or
 
7
 
mph
 
(11
 
km/h)
 
with
 
the 6-speed electronic gearbox
system,
-
some special conditions (battery


charge,
 
engine
 
temperature,
 
braking
 assistance,

 
ambient
 
temperature...)
 where the engine is needed to


assure
 
control
 
of
 
a
 
system.
Stop & Start

55
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The Stop & Start system
requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type of battery must be done only
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For more information on the 12 V
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If the temperature is high
enough, the warning lamp
comes on for less than
one second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp to go off then operate the starter
(Starting position) until the engine
starts. Door or bonnet open
warning lamp
If this comes on, a door or the bonnet
is
  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return
  to   idle.
Do not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related to an automatic change to
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it is strongly recommended that you
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For more advice on driving, particularly
on
 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
READY TO GO
3
Stop & Start

171
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
ECONOMY MODE
After the engine has stopped, with
the
  key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows, courtesy lamps, audio
equipment,
  etc.)   can   only   be   used   for   a  
cumulative duration of thirty minutes, to
prevent

  discharging   of   the   battery.
Once the thirty minutes have elapsed,
the active functions are put on standby
and
  the   battery   warning   lamp   flashes  
accompanied by a message in the
screen.
T

o resume the use of these functions
immediately, start the engine and let it
run
  for   a   few   minutes.
The time available will then be double
the time for which the engine was left
running.
  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery
QUICK HELP
8