remove seats Citroen BERLINGO FIRST RHD 2010 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010, Model line: BERLINGO FIRST RHD, Model: Citroen BERLINGO FIRST RHD 2010 1.GPages: 118, PDF Size: 2.67 MB
Page 5 of 118
FAMILIARISATION
8 -
FRONT SEATS
Never travel with the head
restraints removed.
2. Armrest.
3. Seat back angle adjustment.
4. Forwards-backwards adjustment.
5. Storage drawer
(passenger).
40
1. Head restraint height adjust-
ment.
Page 39 of 118
41SEATS-
FRONT SEATS
The adjustment is correct when
the upper edge of the head re-
straint is level with the top of the
head.
To remove the head restraint, place it
in the top position, press the tabs and
pull it upwards.
To put it back in position, locate the
stems of the restraint in the holes,
taking care to keep them in line with
the seat back.
No person or object must pre-
vent the seat from returning
to its initial position; return to
this position is necessary for
the seat to lock in place.
4. Forwards-backwards
adjustment
Lift the control and slide the seat for-
wards or backwards.
1. Head restraint height
adjustment
To raise or lower the restraint, slide it.
2. Armrests
These can be folded back. 3. Seat back angle adjustment
5. Storage drawer (version with
passenger air bag)
There is a storage drawer under the
front passenger seat.
To open it, lift it and pull. 6. Heated seats switch
Press the switch. The temperature is
controlled automatically.
Pressing the switch again stops opera-
tion.
Note: the command for activation of
heating of the seat(s) remains memo-
rised for two minutes after the ignition
has been switched off.
7. Access to rear seats (version with one
sliding side door only)
Do not place heavy objects
in the drawers.
A. Turn the knob.
B. Pull the lever (version
with one sliding side
door only).
Never drive with the head
restraints removed; they
must be in place and cor-
rectly adjusted. Lift the control to fold the seat back
and move the seat forwards.
On repositioning, the seat returns to
its initial position (driver's side).
Page 40 of 118
SEATS42-
MULTIFUNCTION PASSENGER SEAT
To fold the seat fully:
Pull the control 2 upwards and tilt the
whole seat.
It is not necessary to remove the
head restraint.
This provides access to a box which
enables you to store objects so that
they cannot be seen from outside the
vehicle. I f y o u r v e h i c l e i s n o t fi t t e d w i t h a l o a d
blocking partition, it can accommo-
date long objects (up to 2.10 m).
These must be placed on the front
e d g e o f t h e fl o o r a n d s e c u r e d u s i n g
the rear bar of the boot or using the
lashing rings.
To fold the seat back:
Pull the control
1 upwards and tilt the
seat back.
T h i s p r o v i d e s a fl a t s u r f a c e , r e c e s s -
es for drinks and a strap for retaining
documents.
Page 41 of 118
43SEATS-
To fold the rear bench seat:
- lower the head restraint,
- press control 1 to unlock the seat
back 2 ,
- fold the seat back 2 onto the seat,
- place the seat in the "folded" posi- tion. When repositioning:
- tilt the folded seat rearwards,
- lift the seat back,
- check that the seat is locked cor-
rectly.
Take care not to trap the seat belts.
REAR BENCH SEAT(5 SEAT VERSION) HEAD RESTRAINT
This is of the "comma" type.
High position: press the two tabs at
the same time, lift the head restraint
and raise it.
Low position: push the two tabs at
the same time and press the top to
lower the head restraint.
To remove the head restraint: place
it in the high position, lift it then re-
move it.
Store it inside the vehicle, securing
i t fi r m l y .
To install the head restraint: engage
the rods of the head restraint in the
holes keeping it in line with the seat
back.
Page 48 of 118
49SEATS-
ADVICE ON CHILD SEATS
The incorrect installation of a
child seat in a vehicle com-
promises the child's protection in the
event of an accident.
Remember to fasten the seat belts or
the child seat harnesses keeping the
slack in relation to the child's body to
a minimum, even for short journeys.
For optimum installation of the "for-
ward facing" child seat, ensure that
the back of the child seat is in contact
with the back of the vehicle's seat
and that the head restraint does not
cause any discomfort.
If the head restraint has to be removed,
ensure that it is stored or attached se-
curely to prevent it from being thrown
around the vehicle in the event of
sharp braking. Children under the age of 10 must not
travel in the "forward facing" position
on the front passenger seat, unless
the rear seats are already occupied
by other children, cannot be used or
are absent.
Deactivate the passenger airbag
when a "rear facing" child seat is in-
stalled on the front seat. Otherwise,
the child would risk being seriously
injured or killed if the airbag were to
i n fl a t e .
As a safety precaution, do not leave:
- one or more children alone and
unsupervised in a vehicle,
- a child or an animal in a vehicle which is exposed to the sun, with
the windows closed,
- the keys within reach of children inside the vehicle.
Installing a booster seat
The chest part of the seat belt must
be positioned on the child's shoulder
without touching the neck.
Ensure that the lap part of the seat
belt passes correctly over the child's
thighs.
CITROËN recommends the use of a
b o o s t e r s e a t w h i c h h a s a b a c k , fi t t e d
with a seat belt guide at shoulder level. To prevent accidental
opening of the doors, use
the "Child lock".
Take care not to open the rear win-
dows by more than one third.
To protect young children from the
r a y s o f t h e s u n , fi t s i d e b l i n d s o n t h e
rear windows.
Page 71 of 118
69LIFE ON BOARD-
1. Load-space cover
To install it:
- position the front ends of the load space cover on its support and
press gently to put it in place,
- unfold the load space cover fully,
- position the rear ends of the load space cover on its support and
press gently to put it in place.
To remove it:
- unclip the rear ends,
- fold the load space cover fully,
- unclip the front ends and remove the load space cover.
To store it, fold it like an accordion.
Do not roll it . 2. High load retaining net
T h e h i g h l o a d r e t a i n i n g n e t c a n b e fi t -
ted behind the front or rear seats.
Open the covers
A of the correspond-
ing upper fastenings.
Fit the ends of the metal bar in these
fastenings.
Secure the two net strap hooks be-
hind the front seats, with the rear
seat folded, or in the stowing rings B
o n t h e fl o o r .
The rings are located directly below
the corresponding upper fastenings.
Pull the two straps C taut. 3. Stowing rings
4. Side door storage
compartments
5. Trays between the front and rear seats
6. Seat back storage pockets