bulb Citroen BERLINGO MULTISPACE 2015 2.G User Guide

181
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
3. Direction indicators
T ype B,   PY21W   -   21W   (amber)
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-
 
Remove
  the   bulb   by   pressing   it  
lightly

  while   turning   it   anticlockwise.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing. 4.

Front foglamps
T ype C, H1 - 55W
-
 
Remove
  the   three   clips   and   the  
screw securing the wheel arch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheel   arch   liner   upwards.
-
d isconnect the bulb holder
connector by pressing the tab at
the
  top.-
 
Remove
  the   bulb   holder   by  
squeezing the two clips (at top and
bottom)

  using   a   finger   and   thumb.
-
 
Replace
  the   module   (bulb   holder  
and

  bulb.
-

Carry out the operations in reverse
order

  to   fit   the   module   and   refit   the  
wheel

  arch   liner.
QUICk HELP
8
Changing a bulb

182
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
Side repeater
Type A, WY5W - 5W (amber)
-
Push the repeater towards the rear
and disengage it by pullin

g the
front.
-

Contact a CITR
o Ë n dealer to
obtain a new repeater which is a
sealed
  component.
-
 
T
o   refit,   engage   the   repeater  
towards the rear and bring it
towards

  the   front.
Courtesy lamps
Type A, 12V5W - 5W
-
Unclip the lens by sliding a
screwdriver in the slots on each
side

  of   the   courtesy   lamp.
-
 
Pull
  the   bulb   out   and   change   it.
-

Clip the lens in its housing and
ensure

  that   it   is   secured   correctly.
Front / Rear
Changing a bulb

183
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time   is  
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
on
 
bulbs,
 
refer
 
to
 the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B,
 
PY21W
 
-
 
21W
 
(amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
QUICk HELP
8
Changing a bulb

184
Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed01-2015
Number plate lamps
- Unscrew  the   two   nuts.
-  
Push
  the   pins.
-

If necessary
, disconnect the
connector
  to   remove   the   lamp.
-
 
Change
  the   bulb.
Third brake lamp
Type A, W16W - 16W
T
ype A, W5W - 5W
With tailgate
-
d
isengage the plastic lens using a
screwdriver.
-
 
Change

 
the
 
bulb.
-

Replace the plastic lens and press
on

 
it. With hinged doors
-
 
Unclip

 
the
 
interior
 
trim.
-
d
isconnect the connector by
moving
 
aside
 
its
 
tab.
-

T

urn the bulb holder a quarter turn
anticlockwise.
-
 
Change

 
the
 
bulb.
-
 
Put

 
the
 
bulb
 
holder
 
back
 
in
 
place
 
and

 
reconnect
 
the
 
connector.
-
 
Put

 
the
 
trim
 
back
 
in
 
place.
Changing a bulb