coolant temperature Citroen BERLINGO MULTISPACE 2015 2.G Owner's Manual

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
28
Dials
1. Distance  recorder   in   kilometres   /  miles.
2.
 
Display
  screen.
3.
 
Fuel
  gauge,   coolant   temperature.
4.
 
Rev
  counter.
5.
 
T
rip   distance   recorder   /   service  
indicator

  reset.
6.
 
Instrument
  panel   lighting   dimmer.Level 1
INSTRUMENT PANELDisplay screens
Screens
The format of the information presented in the screen depends on
the
  vehicle's   equipment   level.
Level 2
with the touch screen tablet
Instruments and controls

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
32
WARNING LAMPS
Warning lamp is indicatesSolution - action
STOP on, associated
with another
warning
lamp
  and  
accompanied

 
by

  a   message  
in

  the   screen.major
  faults   linked   with  
the

  "Brake   fluid   level",  
"Engine oil pressure and
temperature",

  "Coolant  
temperature",

  "Electronic  
brake

  force   distribution"   and  
"Power steering" warning
lamps.Y

ou must stop as soon as it is safe to do
so. Park and switch off the ignition. Have it
checked by a CITROËN dealer or a qualified
workshop.
Parking
brake / Brake
fluid level /
EBFD on.
that the parking brake is applied or
  has   not   been   released   fully.Releasing the parking brake switches off the warning  lamp.
on. low
 
brake
 
fluid
 
level. Top   up   using   a   fluid   recommended   by   CITROËN.
remaining on even though the level
is correct and
associated with the
ABS
 
warning
 
lamp.
a fault with the electronic
brake  force   distribution. You must stop as soon as it is safe to do so.
Park and switch off the ignition.
Have it checked by a CITROËN dealer or a
qualified workshop.
Engine oil
pressure and
temperature on while
driving.
low pressure or a high
temperature. Park
  and   switch   off   the   ignition   then   allow   to   cool.
Visually
  check   the   level.
Chapter
  7,   "Levels"   section.
remaining on, even though the
level
  is   correct.a major fault. Have   it   checked   by   a   CITROËN   dealer   or   a  qualified
  workshop.
Each time the vehicle is started: a series of warning lamps comes on applying a self-test check. They   go   off   almost   immediately.
Engine   running:   the   lamp   becomes   a   warning   if   it   remains   on   continuously   or   flashes.
This
  initial   warning   may   be   accompanied   by   an   audible   signal   and   a   message   in   the   screen.
Do
  not   ignore   these   warnings.
Instruments and controls

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
33Warning lamp isindicatesSolution - action
Coolant
temperature
and level on with needle
in the red
zone.
an
  abnormal   increase   in  
temperature.Park

  and   switch   off   the   ignition   then   allow   to   cool.  
V

isually   check   the   level.
flashing. a
  drop   in   the   coolant   level.Chapter
  7,   "Levels"   section.
Contact
  a   CITROËN dealer   or   a   qualified  
workshop.
Service on

  temporarily. minor   faults   or   warnings.Consult
  the   alert   log   in   the   display   or   screen.
If
  your   vehicle   is   equipped   with   a   trip   computer   or  
a

  screen:   refer   to   the   "Steering   mounted   controls"  
section

  in   Chapter   4.
Contact
  a   CITROËN   dealer   or   a   qualified  
workshop.
remaining

  on. major   faults.
Seat belt not
fastened on then
flashing.
the
  driver   and/or   front  
passenger has not fastened
their

  seat   belt.Pull
  the   strap   then   insert   the   tongue   in   the   buckle.
accompanied
 
by an audible
signal then
remains

  on.the
  vehicle   is   moving   with  
the

  driver's   and/or   front  
passenger's seat belt not
fastened.Check

  that   the   seat   belt   is   fastened   by   pulling   the  
strap.
Chapter

  5,   "Seat   belts"   section.
ECO on.
The
  Stop   &   Start system  
has put the engine in
ST

OP
 
mode   following   a  
vehicle

  stop   (red   light,   traffic  
jam, etc...).As

  soon   as   you   want   to   move   off,   the   warning  
lamp

  goes   off   and   the   engine   restarts  
automatically

  in   START
 
mode.
flashes
  for   a  
few seconds,
then

  goes   off.STOP
 

mode   is   temporarily  
unavailable.
or
ST

ART
 
mode   has   been  
invoked

  automatically.Chapter
  3,   "Stop   &   Start"   section.
Instruments and controls
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
40
FUEL GAUGEC OOLANT TEMPERATURE
The needle is positioned before the
red zone:
  normal   operation.
In arduous conditions of use or hot
climatic
  conditions,   the   needle   may  
move

  close   to   the   red   graduations.What you should do if the needle
enters the red zone:
Reduce your speed or let the engine
run
  at   idle.
What you should do if the warning
lamp comes on:
-  
stop
  immediately,   switch   off   the  
ignition.

 
The
  fan   may   continue   to  
operate

  for   a   certain   time,   up   to  
approximately

  10   minutes,
-
wait for the engine to cool down in
order

  to   check   the   coolant   level   and  
top

  it   up   if   necessary.
As   the   cooling   system   is   pressurised,  
follow the procedure below to avoid the
risk

  of   scalding:
-
wait at least one hour after
switching of

f the engine before
carrying   out   any   work,
-  
unscrew
  the   cap   by   1/4   turn   to  
allow the pressure to drop,
-

when the pressure has dropped,
check

  the   level   in   the   header   tank,
-  if   necessary,   remove   the   cap   to   top  
up.
If

  the   needle   remains   in   the   red  
zone,

  have   the   system   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop.Refer

  to   chapter   7,   "Levels"  
section.
Refer

 
to
 
chapter
 
7,
 
"Fuel"
 
section.
The
 
fuel
 
level
 
is
 
tested
 
each
 
time
 
the
 
key

 
is
 
turned
 
to
 
the
 
"running"
 
position.
The
 
gauge
 
is
 
positioned
 
on:
-

1:

 
the
 
fuel
 
tank
 
is
 
full,
 
approximately

 
60
 
litres.
-

0:

the reserve is now being used,
the
 
warning
 
lamp
 
comes
 
on
 
continuously

.
 
The

 
reserve
 
when
 
the

 
warning
 
first
 
comes
 
on
 
is
 
approximately

 
8
 
litres.
Instruments and controls

145
Berlingo-2-VP_en_Chap06_Accessoire_ed01-2015
For more information about weights and towed loads, refer to
chapter  9,   "Weights"   section.
TOWING A TRAILER , A CARA VAN ...
Distribution of loads
d

istribute the load in the trailer so
that
  the   heaviest   objects   are   as  
close as possible to the axle and
the nose weight is close to the
maximum

  authorised   without,   however,  
exceeding

  it.
Cooling
Towing a trailer on a slope increases
the
  coolant   temperature.a s the fan is electrically controlled, its
cooling capacity is not dependent on
the
  engine   speed.
You should therefore use a high gear
to lower the engine speed and reduce
your
  speed.
In all cases, pay attention to the
coolant
  temperature.
Driving advice
A towed   vehicle   must   free   wheel:  gearbox
  in   neutral.
Towing a trailer
aCCESSoRIES
6

146
Berlingo-2-VP_en_Chap06_Accessoire_ed01-2015
Good Practice
In certain cases of particularly arduous
use  (towing   the   maximum   load   up   a  
steep

  slope   in   high   temperatures),   the  
engine

  automatically   limits   its   power.  
In this case,

the air conditioning is
automatically
  cut   off   to   save   engine  
power

.
Tyres
Check
  the   tyre   pressures   of   the   towing  
vehicle and of the trailer

, observing the
recommended
  pressures.
Chapter
  7,   "Levels"   section.
If
  the   coolant   temperature  
warning

  lamp   comes   on,   stop  
the vehicle and switch of

f the
engine
  as   soon   as   possible.Brakes
Towing
  increases   the   braking   distance.  Drive
  at   a   moderate   speed,   change  
down

  early   and   brake   gradually.
Towbar
We recommend the use of genuine CITRo Ë n towbars and their wiring
harnesses, which have been tested
and
  approved   from   the   design   stage   of  
your vehicle, and that you entrust the
fitting

  of   this   equipment   to   a   CITROËN  
dealer

.
If
  this   equipment   is   not   fitted   by   a  
CITROËN

  dealer,   it   is   imperative   that  
it

  is   fitted   using   the   electrical   pre-
equipment
  installed   at   the   rear   of   the  
vehicle and in accordance with the
manufacturer's

  instructions.
In accordance with the general
instructions
  a   reminder   of   which   has  
been given above, we draw your
attention

  to   the   risk   associated   with  
fitting

  a   towbar   or   electrical   accessory  
not

  recommended   by   CITROËN.  
Fitting

  such   equipment   could   result   in  
the failure of your vehicle's electronic
system.

  Please   obtain   information   from  
the

  Manufacturer   before   fitting   this   type  
of

  equipment.
Side wind
Sensitivity
 
to
 
side
 
wind
 
is
 
increased.
 
Drive

 
smoothly
 
and
 
at
 
a
 
moderate
 
speed.
ABS/DSC
The

 
ABS

 
or
 
DSC
 
systems
 
only
 
control
 
the

 
vehicle,
 
not
 
the
 
trailer
 
or
 
caravan.
Parking sensors
The
 
rear
 
parking
 
sensors
 
system
 
does
 
not

 
function
 
while
 
the
 
vehicle
 
is
 
towing.
Chapter
 
9,
 
"Identification
 
markings"

 
section.
Towing a trailer

156
Berlingo-2-VP_en_Chap07_Verification_ed01-2015Berlingo-2-VP_en_Chap07_Verification_ed01-2015
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels