display Citroen BERLINGO MULTISPACE RHD 2015 2.G User Guide

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
42
trip recorder zero reset button
after this operation, if you wish
to   disconnect   the   battery,   lock  
the vehicle and wait for at least
five minutes,

  otherwise   the   zero   re-set  
will

 
not   be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on, the
engine oil level is indicated for a few
seconds,
  after   the   service   information. Oil level correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge fault
Flashing of "OIL--"
indicates  
a
 
malfunction of the engine oil level


indicator.   Contact
 a

  CITROËN   dealer   or   a   qualified
 workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been of
f for
more
  than   30   minutes.
d
ipstick
A   =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting
reaches

  the   minimum   (or  
maximum)

 
setting,   release   the   button  
then press it again to increase (or
reduce)

 
the
 
brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero re-set
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.
Instruments and controls

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
48
Going into engine StArt mode
The "EcO" warning lamp goes
  off   and   the   engine   starts:
- with a manual gearbox , when you
fully depress the clutch pedal,
-

with the 6-speed electronic gear
control gearbox

:
●
 
gear
  lever   in   position   A or M,
when
  you   release   the   brake  
pedal,
●

 
or
  gear   lever   in   position  n and
the
  brake   pedal   released,   when  
you

  move   the   gear   lever   to  
position

A or M,
●
 
or
  when   you   engage   reverse  
gear

.
With
  a   manual   gearbox   in   STOP
 mode,

  if   a   gear   is   engaged   without  
fully depressing the clutch pedal, a
warning

  lamp   comes   on   or   a   message  
is

  displayed   asking   you   to   depress   the  
clutch

  pedal   to   restart   the   engine.Special cases: S
t
A
rt invoked
automatically
For   your   safety   and   comfort,   START
 
is  
invoked

  automatically   when:
-
you open the driver's door
,
-
you unfasten the driver's seat belt,
-
the speed of the vehicle exceeds
15
  mph   (25   km/h)   with   a   manual  
gearbox

  or   7   mph   (11   km/h)   with  
the

  6-speed   electronic   gearbox  
system,
-

 
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.In this case the

"E c O"
warning
  lamp   flashes   for   few  
seconds,

  then   goes   off.
t

his operation is perfectly normal.
deactivation
At any time, press the "EcO
OFF" switch to deactivate the
system.
This
 
is
 
confirmed   by   the   switch   warning  
lamp

 
coming   on   accompanied   by   a  
message

  in   the   screen.
If
 
the
 
system   has   been   deactivated  
in

 
STOP
 

mode,   the   engine   restarts  
immediately

.
Stop & Start

 57
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
cruISE cOntrOL "cruISE"
In order for it to be programmed or activated,  the   vehicle   speed   must   be  
greater

  than   25   mph   (40   km/h)   with   at  
least

  4th   gear   engaged. This cruise control shows the function
selection
  status   in   the   instrument   panel  
and

  displays   the   programmed   speed:
Function selected,
display of the "Cruise
Control"   symbol.
Function deactivated,
OFF.
Function activated
Vehicle speed above
the   programmed  
speed, which is
displayed

  flashing.
o

perating fault
detected,
OFF - the dashes
flash.
"This is the speed at which the driver
wishes
 
to
 
drive".
This
 
aid
 
to
 
driving
 
in
 
free-flowing
 
traffic

 
enables
 
the
 
vehicle
 
to
 
maintain
 
the

 
speed
 
programmed
 
by
 
the
 
driver,
 
unless

 
a
 
steep
 
gradient
 
makes
 
this
 
impossible.
Steering mounted controls
EASE OF uSE and cOMFOrt
4

60
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
However, pressing the pedal beyond
this  point   of   resistance   to   the   floor  
allows

  the   programmed   speed   to   be  
exceeded.

 
T
o   resume   use   of   the   limiter,  
simply

  reduce   the   pressure   on   the  
accelerator pedal gradually and return
to

  a   speed   below   that   programmed.
t

he operating actions may be
carried out when stationary, with the
engine running, or with the vehicle
moving. This
  speed   limiter   shows   the   function  
selection

  status   in   the   instrument   panel  
and

  displays   the   programmed   speed:
SPEEd LIMItEr "LIMIt"
Function selected,
displaying of the
"Speed
  Limiter"  
symbol.
Function deactivated,
last

  programmed  
speed -

OFF.
Function activated
Vehicle speed above
the
  programmed  
speed, which is
displayed

  flashing.
o

perating fault
detected,
OFF - the dashes
flash.
"This is the selected speed which the
driver
 
does
 
not
 
wish
 
to
 
exceed".
This
 
selection
 
is
 
made
 
with
 
the
 
engine
 
running while stationary or with the
vehicle

 
moving.
 
The

 
minimum
 
speed
 
which

 
can
 
be
 
programmed
 
is
 
20
 
mph
 
(30

 
km/h).
The speed of the vehicle responds
to the pressure of the driver's foot as
far as the accelerator pedal point of
resistance which indicates that the
programmed
 
speed
 
has
 
been
 
reached.
Steering mounted controls

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
 65
Good practice
For maximum cooling or heating of the passenger  compartment,   it   is   possible  
to exceed the value 15 by turning until
LO

  is   displayed   or   the   value   27   by  
turning

  until   HI   is   displayed.
o

n entering the vehicle, the inside
temperature
  may   be   much   colder  
(or
  warmer)   than   is   comfortable.  
There
 
is no advantage in changing the value
displayed

  in   order   to   quickly   reach   the  
level

  of   comfort   required.  
The
  system  
will

  use   its   maximum   performance   to  
reach

  the   comfort   value   set.
dIGItAL AIr c O nd I t IO n I n G WI t H SEPA r At E SE tt I n GS
Automatic operation
AutO comfort programme
This   is   the   normal   air   conditioning  
system

  operating   mode.
d
river or passenger side comfort
value
The value indicated in the screen
corresponds   to   a   level   of   comfort   and  
not

  a   temperature   in   degrees   Celsius  
or

  Fahrenheit.
Turn this control to the left
or to the right to decrease or
increase   the   value.  
A 
setting  
around the value 21 provides
optimum

  comfort.   However,  
depending

  on   your   requirements,   a  
setting

  between   18   and   24   is   usual.
d

o not cover the sunshine sensor
located
  on   the   dashboard.
Press this button, the A
ut
O

symbol
  is   displayed.
In accordance with the
comfort
  value   selected,  
the

  system   controls   the  
distribution,

  the   flow   and   the   intake  
of

  air   to   guarantee   comfort   and   a  
sufficient

  circulation   of   air   in   the  
passenger

  compartment.   No   further  
action

  on   your   part   is   required.
When the engine is cold, to prevent an
excessive diffusion of cold air, the air diffuser
will  reach   its   optimum   level   gradually.
For
  your   comfort,   the   settings   are   stored
 when the ignition is switched of

f and are
reinstated
  the   next   time   the   vehicle   is
 started.
The

  automatic   function   will   no   longer   be
 maintained

  if   you   change   a   setting   manually
 (AUT

O   is   cleared).
FOr tHE drIVEr And PASSEnGEr
Ventilation
EASE OF uSE and cOMFOrt
4

Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
66
Manual operation
You can, according to your
requirements,  make   a   different   selection from

  that   offered   by   the   system   by
 changing

  a   setting.  
The
  other   functions
 will

  still   be   controlled   automatically.
 Pressing the

A ut
O
button restores fully
automatic
  operation.
Air distribution
Pressing this button several
times
  in   succession   directs  
the

  air   flow   towards:
-

the windscreen,
-


the windscreen and footwells,
-


the footwells,
-


the side vents, central vents and
footwells,
-

 
the
  side   vents   and   central   vents.Air flow
Press the small fan button to
reduce
  the   flow   or   the   large
fan button to increase the
flow.
On
  the   display,   the   blades   of   the   fan   fill  
when

  the   flow   is   increased.
Switching the air
conditioning On / Off
Press this button, the A/
c
symbol
  is   displayed   and   the  
air

  conditioning   is   activated.
d
eactivating the system
Press
  the   air   flow   small fan
button
  until   the   fan   symbol  
disappears

  from   the   display.
This action deactivates all of the
system's
  functions,   with   the   exception  
of the air recirculation and rear screen
demisting

  (if   fitted   on   your   vehicle).  
Y

our   comfort   setting   is   no   longer  
maintained

  and   is   switched   off.Intake of exterior air / r
ecirculation of interior air
Press this button to
recirculate
  the   interior   air.  
The

  recirculation   symbol   is  
displayed.
Pressing the

large fan
button or the A
ut
O
button
reactivates
  the   system   with  
the values set before it was
deactivated.Recirculation prevents exterior odours


and
  smoke   from   entering   the   passenger
 compartment.

 
A
void   prolonged   operation
 in

  interior   air   recirculation   mode   (risk   of
 condensation,

  odour   and   humidity).
Pressing this button again activates the
intake
  of   exterior   air.
Pressing this button again switches off
the
  air   conditioning.
The ventilation outlet, located
in the glove box, diffuses cool
air (if the air conditioning is
on) regardless of the reference
temperature
  requested   in   the  
passenger

  compartment   and  
regardless

  of   the   exterior   temperature.
For
  your   comfort,   do   not   deactivate   the  
system

  for   long   periods.  
Ventilation

 107
Berlingo_2_VP_en_Chap05_Securite_ed02-2014
The audible and/or visual rear parking sensor  system   consists   of   four  
proximity

  sensors,   installed   in   the  
rear

  bumper.  
The
  sensors   detect   any  
obstacle

  which   enters   the   field:   person,  
vehicle, tree, fence, behind the vehicle
during

  the   manoeuvre.
Certain
  objects   detected   at   the  
beginning

  of   the   manoeuvre   will   no  
longer be detected at the end of the
manoeuvre

  due   to   the   blind   spots  
between

  and   below   the   sensors.  
Examples:

  stake,   roadworks   cone   or  
pavement

  post.
Engage reverse gear
r

EA
r
PA
r
KI
n
G SE
n
SO
r
S
display in the screen
Stop the assistance
Change to neutral.
An
 
audible
 
signal
 
confirms
 
the
 
activation

 
of
 
the
 
system
 
by
 
engaging
 
reverse

 
gear.
The
 
proximity
 
information
 
is
 
indicated
 
by

 
an
 
audible
 
signal
 
which
 
becomes
 
more

 
rapid
 
as
 
the
 
vehicle
 
approaches
 
the

 
obstacle.
 
When
 
the
 
distance
 
between the rear of the vehicle and
the

 
obstacle
 
is
 
less
 
than
 
approximately
 thirty
 
centimetres,
 
the
 
audible
 
signal
 becomes
 
continuous.
Parking sensors
SaFETY
5

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
144
cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
topping up
The

 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required

 
to
 
top
 
up
 
the
 
level,
 
have
 
the
 
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your safety , we would advise that you use
products
  of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
diesel additive level
( d iesel with particle
emission filter)
topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
emission
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
150
range indicators
When switching on the ignition, an
indicator  gives   an   estimate   of   the  
distance that can be travelled with
your vehicle before engine starting
is

  automatically   prevented,   once   the  
vehicle starts using the reserve of a

dBlue
® or after a fault is detected with
the
 
SCR   system.
In
 
the
 
event   of   simultaneous   system  
fault and low a

dBlue
® level, the
shortest
 
range
 
is
 
the
 
one   displayed.
In the event of the risk
of non-starting related to a lack
of AdBlue
®
The engine start prevention
system   required   by   regulations   is  
activated

  automatically   once   the  
a
dBlue
® tank is empty.
range greater than 1 500 miles (2 400 km)
When the ignition is switched on, no
information   on   range   is   displayed  
automatically

  in   the   instrument   panel.
Pressing this button
displays the driving range
temporarily.
Above
  3   000   miles  
(5
  000   km),   the   value   is  
not

  specified. When switching on the ignition, the
UREA warning
  lamp   comes   on,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.:   "Top   up  
emissions

  additive:   Starting   prevented  
in

  900   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed

  every   150   miles   (300   km)  
until

  the   additive   tank   has   been  
topped-up.
Go

  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
r

emaining range between 350 and
1500 miles (600 and 2 400 km)
adBlue® additive

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
151
When switching on the ignition, the
SERVICE  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal   and  
the

  display   of   a   message   (e.g.   "Top   up  
emissions

  additive:   Starting   prevented  
in

  350   miles")   indicating   the   remaining  
range

  expressed   in   miles   or   kilometres.
When
  driving,   the   message   is  
displayed every 30 seconds until the
additive

  tank   has   been   topped-up.
Go
  to   a   CITROËN   dealer   or   a   qualified  
workshop

  to   have   the  
AdBlue® tank topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
tank
 
yourself.
Refer
 
to
 
the
 
"Topping-up"
 
section.
o

therwise you will not be able to
restart
 
your
 
engine. When switching on the ignition, the
SERVICE
  warning   lamp   comes   on  
and

  the   UREA
 
warning   lamp   flashes,  
accompanied

  by   an   audible   signal  
and

  the   display   of   the   message  
"T

op   up   emissions   additive:   Starting  
prevented".
The

a dBlue
® tank is empty: the system required
 
by
 
regulations   prevents  
engine

 
starting. To be able to start the engine,
we
  recommend   that   you   call   on  
a

  CITROËN   dealer   or   a   qualified  
workshop

  for   the   top-up   required.   If  
you carry out the top-up yourself, it is
essential

  to   add   at   least   3.8   litres   of  
a dBlue
® to the tank.
r

emaining range between 0 and
350 miles (0 and 600 km) Breakdown related to a lack of
AdBlue
® additive
Refer   to   the   "Topping-up"   section.
adBlue® additive
CHECkS
7