stop start Citroen BERLINGO MULTISPACE RHD 2015 2.G User Guide

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
49
reactivation
Press the "EcO OFF" switch again.
The   system   is   active   again;   this   is  
confirmed

  by   the   switch   warning  
lamp

  going   off   and   a   message   in   the  
instrument

  panel.
The
  system   is   reactivated  
automatically

  at   every   new   start  
using

  the   key.
Operating fault
In the event of a malfunction with  the   system,   the   "E c O
OFF"
  switch   warning   lamp  
flashes,

  then   comes   on  
continuously

.
Maintenance
Before working under the bonnet, deactivate  the   Stop   &   Start   system  
to

  avoid   any   risk   of   injury   resulting  
from

  automatic   operation   of   START
 mode.
This

  system   requires   a   specific  
battery

  with   a   special   specification  
and

 
technology   (reference   numbers  
available

  from   a   CITROËN   dealer   or   a  
qualified

  workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
The
  Stop   &   Start   system   makes  
use

  of   advanced   technology.  
All
 
work

  on   this   type   of   battery   must  
be done only by a CITR

o Ë n dealer or
a
 
qualified   workshop.
have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 

mode,
 
the

 
vehicle
 
may
 
stall.
 
All

 
of
 
the
 
warning
 
lamps

 
in
 
the
 
instrument
 
panel
 
come
 
on.

 
It
 
is
 
then
 
necessary
 
to
 
switch
 
off
 
the ignition and start the engine again
using

 
the
 
key.
Stop & Start
REadY To Go
3

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
50
Good practice when stopping Good practice when starting
diesel pre-heating warning
lamp
If
  the   temperature   is   high  
enough,

  the   warning   lamp  
comes

  on   for   less   than  
one

second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp
 
to
 
go   off   then   operate   the   starter  
(Starting position) until the engine
starts.
d
oor or bonnet open
warning lamp
If this comes on, a door or the bonnet is   not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (
d iesel engine) to
return
  to   idle.
d

o not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
StArt I n G A nd S tOPPI n G
running and accessories position.
T o   unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
S
t
OP
position:   steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Starting and stopping

Berlingo_2_VP_en_Chap03_Pret-a-partir_ed02-2014
51
HILL StA rt ASSIS t
This system (also called HHC - Hill Holder
  Control),   linked   to   the   dynamic  
stability

  control   system,   makes   hill  
starts easier and is activated in the
following

  conditions:
-
 
the
  vehicle   must   be   stationary,  
engine

  running,   foot   on   the   brake,
-
 
the
  gradient   of   the   road   must   be  
steeper than 5%,
-

 
uphill,
  the   gearbox   must   be   in  
neutral or in a gear other than
reverse,
-

 
downhill,
  reverse   gear   must   be  
engaged.
The Hill Start
a

ssist function is
a
  driving   aid   system.   It   is   not   an  
automatic

  vehicle   parking   function   or  
an

  automatic   parking   brake.
Operation
With the brake pedal and clutch pedal pressed,  from   the   time   you   release   the  
brake

  pedal   you   have   approximately  
2 seconds before the vehicle starts to
roll

  back   and   without   using   the   parking  
brake

  within   which   to   move   off.
During
  the   moving   off   phase,   the  
function

  is   deactivated   automatically,  
gradually

  releasing   the   braking  
pressure.

  During   this   phase,   the  
characteristic

  noise   of   mechanical  
release

  of   the   brakes   may   be   heard,  
indicating

  the   imminent   movement   of  
the

  vehicle.
Operating fault
Hill start assist is deactivated in the
following   situations:
-

when the clutch pedal is released,
-

 
when
  the   parking   brake   is   applied,
-

when the engine is switched of
f,
-
 
when
  the   engine   stalls.
If
  a   malfunction   of   the  
system

  occurs,   this  
warning

  lamp   comes   on  
accompanied

  by   an   audible  
signal

  and   confirmed   by  
a

  message   in   the   screen.   Have   the  
system

  checked   by   at   a   CITROËN  
dealer

  or   a   qualified   workshop.
Starting and stopping
REadY To Go
3

53
Berlingo_2_VP_en_Chap04_Ergonomie_ed02-2014
LEd dAYtIME runnInG LAMPS
Rear foglamps (amber, 2nd rotation  of   the   ring   forwards).
Front
  foglamps   (green,   1st  
rotation

  of   the   ring   forwards).
Front and rear foglamps
Rotate ring B forwards to switch on
and
 
rearwards   to   switch   off.  
The
  status  
is

 
confirmed   by   the   warning   lamps   in  
the

 
instrument   panel.
They
 
operate   with   the   sidelamps   and  
dipped

 
beam   headlamps. Do   not   forget   to   switch   them   off  
when

  they   are   no   longer   needed.
Operation   of   the   automatic   illumination  
of

  headlamps   switches   off   the   rear  
foglamps,

  but   the   front   foglamps  
remain

  on.
To switch off the front and rear
foglamps,   turn   the   ring   rearwards   twice  
in

 
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the   sunshine   sensor   may   detect  
sufficient

  light.  
As
  a   consequence,  
the

 
lighting   will   not   come   on  
automatically

.
If
  necessary,   you   must   switch  
on

  the   dipped   beam   headlamps  
manually

.
d

o not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination   of   headlamps   and   for   the  
automatic

  rain   sensitive   wipers.
Activation
Turn the ring to the A
ut
O
  position.  
The activation of this function is
accompanied

  by   a   message   in   the  
screen.
d

eactivation
Turn
  the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied

  by   a   message   in   the  
screen.
The

 
function   is   deactivated   temporarily  
when

  you   use   the   manual   lighting  
control

  stalk. The
  sidelamps  
and

  dipped   beam  
headlamps

  switch  
on

  automatically   if  
the light is poor

, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light

  becomes   bright   enough   or   the  
windscreen

  wipers   stop.
This
  function   is   not   compatible   with   the  
daytime

  running   lamps.
o

n starting the vehicle, in daylight the
LED
 
daytime
 
running
 
lamps
 
come
 
on
 
automatically

.
If
 
the
 
sidelamps
 
and
 
headlamps
 
are
 
switched

 
on
 
manually
 
or
 
automatically,
 
the

 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day   is   not   a   legal   requirement,   you   can  
activate or deactivate the function via
the

  configuration   menu.
If the user does not operate any
equipment
 
for
 
30
 
minutes,
 
the
 
Economy

 
mode
 
engages
 
to
 
avoid
 
discharging

 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp
 
operation
 
is
 
not
 
affected
 
by
 
Economy

 
mode.
In clear weather or in rain, both day
and
 
night,
 
rear
 
foglamps
 
dazzle
 
and
 
their

 
use
 
is
 
prohibited.
Refer to chapter 8, "Battery
section".
Steering mounted controls
EaSE oF USE and CoMFoRT
4

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
144
cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
topping up
The

 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required

 
to
 
top
 
up
 
the
 
level,
 
have
 
the
 
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your safety , we would advise that you use
products
  of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
diesel additive level
( d iesel with particle
emission filter)
topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
emission
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
156
- obtain a bottle of adBlue®. After first
 
checking
 
the
 
use-by
 
date,  
read carefully the instructions on
use on the label before pouring
the contents of the bottle into your
vehicle's

a
dBlue
® tank.
Important
:
 
if
 
your   vehicle's
 
a

dBlue
® tank is completely 
empty
 
-
 
which   is   confirmed   by   the alert

 
messages   and   the   impossibility
 of

 
starting
 
the   engine,   you   must   add   at
 least

 
3.8
 
litres   (so   two   1.89   litre bottles). -
 
After
  emptying   the   bottle,   wipe  
away

  any   spillage   around   the   tank  
filler

  using   a   damp   cloth.
If any additive is split or splashed,
wash   immediately   with   cold   water  
or

  wipe   with   a   damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.
-  
Refit
  the   blue   cap   to   the   tank   and  
turn

  it   a   6
th of a turn clockwise, to its stop.
-
 
Close

 
the
 
filler   flap.
n
ever dispose of
a
dBlue
® additive
bottles
 
in
 
the
 
household
 
waste.  
Place

 
them
 
in
 
a
 
special
 
container  
provided

 
this
 
purpose
 
or
 
take
 
them   to  
your

 
dealer.
Important:
 
in the event of a top-
up after a breakdown because
of a lack of additive, signalled
by
 
the
 
message
 
"Top
 
up
 
emissions  
additive:

 
Starting
 
prevented",
 
you   must  
wait

 
around
 
5
 
minutes
 
before
 
switching  
on the ignition,

without opening the
driver's door, locking the vehicle or
introducing the key into the ignition
switch.
Switch on the ignition, then, after
10
 
seconds,
 
start
 
the
 
engine.
adBlue® additive

157
Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
BAttE rY
Before disconnecting the battery, you
must
  wait   for   2   minutes   after   switching  
of

f   the   ignition.
Never
  disconnect   a   terminal   when   the  
engine

  is   running.
Never
  charge   a   battery   without   first  
disconnecting

  the   terminals.
a

fter every reconnection of the battery,
switch
  on   the   ignition   and   wait   1   minute  
before starting to allow the electronic
systems

  to   be   initialised.   If   problems  
remain

  after   doing   this,   please   contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
a

fter changing bulbs, wait
approximately
  3   minutes   before  
reconnecting

  the   battery.
It is advisable to disconnect the
battery if the vehicle is not to be
used

 
for
 
a
 
period
 
of
 
more
 
than
 
one month.
to charge the battery using a
battery charger
- disconnect the battery,
-
Follow the instructions for use
given by the battery charger
manufacturer

,
-

Reconnect starting with the
negative

  (-)   terminal,
-
 
Check
  that   the   terminals   and  
connectors

  are   clean.   If   they   are  
covered with sulphate (white or
greenish

  deposit),   disconnect   them  
and

  clean   them.
to start the vehicle from
another battery
- Connect the red cable to the
positive   (+)   terminals   of   the  
two

batteries,
-

Connect one end of the green
or

  black   cable   to   the   negative   (-)  
terminal

  of   the   slave   battery,
-

Connect the other end of the green
or

  black   cable   to   an   earth   point   on  
the

  broken   down   vehicle   as   far   as  
possible

  from   the   battery,
-


o perate the starter, let the engine run,
-

W
ait for the engine to return to idle,
then
  disconnect   the   cables.
The presence of this label
indicates the use of a 12 V
lead-acid battery with special
technology
 
and
 
specification,
 
for
 
which
 
the

 
involvement
 
of
 
a
 
CITROËN
 
dealer
 
or

 
qualified
 
workshop
 
is
 
required
 
when
 
replacing

 
or
 
disconnecting
 
the
 
battery.
Failure to observe this
recommendation
 
may
 
cause
 
premature
 wear
 
of
 
the
 
battery.
After
 
refitting
 
the
 
battery,
 
the
 
Stop &
 
Start

 
system
 
will
 
only
 
be
 
active
 
after
 
several hours depending on the
climatic

 
conditions
 
and
 
the
 
state
 
of
 
charge of the battery (up to about
8 hours).
The Stop & Start battery does not have
to

 
be
 
disconnected
 
for
 
charging.
Battery
QUICk HELP
8

158
Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
EcOnOMY MOdE
after the engine has stopped, with
the   key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows,
  courtesy   lamps,   audio  
equipment,

  etc.)   can   only   be   used   for   a  
cumulative

  duration   of   thirty   minutes,  
to
  prevent   discharging   of   the   battery.
Once
  the   thirty   minutes   are   over,   the  
active functions are put on standby
and

  the   battery   warning   lamp   flashes  
accompanied

  by   a   message   in   the  
screen.
T

o   resume   the   use   of   these   functions  
immediately

,   start   the   engine   and   let   it  
run

  for   a   few   minutes.
The
  time   available   will   then   be   double  
the

  time   for   which   the   engine   was   left  
running.

  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery

186
Berlingo_2_VP_en_Chap09_Caract-technique_ed02-2014
diesel Engines / Weights
5-seatEngine Gearbox GearsEngine oil
capacity* (litres)
u

nbraked
trailer (kg)
r

ecommended nose
weight (kg)
1.6 H
d i 75 hp Manual 5-740 50
1.6 H
d i 75 hp FAP Manual 5-715 70
1.6 H
d i 90 hp Manual 53.75 740 55
1.6 H
d i 90 hp FAP Manual 53.75 750 55
1.6 H
d i 92 hp E c OManual 53.75 715 70
1.6 H
d i 92 hp FAP Manual 53.75 715 70
1.6 e-H
d I 92 hp
E
c O Manual
5
3.75 690
70
Electronic 6 75070
1.6 e-H
d i 92 hp FAP Manual
5
3.75 690
70
Electronic 6 75070
1.6 H
d i 110 hp FAP Manual 53.75 750 55
1.6 H
d i 112 hp FAP Manual 53.75 735 70
FAP:
  particle   filter.
e-H
d i:  
model
  equipped   with   Stop   &   Start.
*
  Capacity   with   oil   filter   replacement.
Weights

 187
Berlingo_2_VP_en_Chap09_Caract-technique_ed02-2014
7-seatEngine Gearbox GearsEngine oil
capacity* (litres)
u

nbraked
trailer (kg)
r

ecommended nose
weight (kg)
1.6 H
d i 90 hp Manual 53.75 750 70
1.6 H
d i 90 hp FAP Manual 53.75 750 70
1.6 H
d i 92 hp FAP Manual 53.75 750 70
1.6 e-H
d I 92 hp FAP Manual 53.75 750 70
1.6 H
d i 110 hp FAP Manual 53.75 750 70
1.6 H
d i 112 hp FAP Manual 53.75 750 70
FAP:
  particle   filter.
e-H
d i:  
model
  equipped   with   Stop   &   Start.
*
  Capacity   with   oil   filter   replacement..
tEcHnIcAL dAtA
9
Weights