stop start Citroen BERLINGO MULTISPACE RHD 2015.5 2.G User Guide

55
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Maintenance
Before working under the bonnet, deactivate  the   Stop   &   Start   system  
to

  avoid   any   risk   of   injury   resulting  
from

  automatic   operation   of   START
 mode.
This

  system   requires   a   specific  
battery

  with   a   special   specification  
and

 
technology   (reference   numbers  
available

  from   a   CITROËN   dealer   or   a  
qualified

  workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
The
  Stop   &   Start   system   makes  
use

  of   advanced   technology.  
All
 
work

  on   this   type   of   battery   must  
be done only by a CITR

o Ë n dealer or
a
 
qualified   workshop.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If  the   temperature   is   high  
enough,

  the   warning   lamp  
comes

  on   for   less   than  
one

second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp
 
to
 
go   off   then   operate   the   starter  
(Starting position) until the engine
starts.Door or bonnet open


warning lamp
If   this   comes   on,   a   door   or  
the bonnet is not closed
correctly

,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (
d iesel engine) to
return
 
to
 
idle.
d

o not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
 
parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
REadY To Go
3
Stop & Start

57
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Starting and switching off
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
A FEW DRIVING
RECOMMENDA
TIONS
observe the driving regulations at all
times   and   remain   vigilant   whatever   the  
traffic

  conditions.
Pay
  close   attention   to   the   traffic   and  
keep

  your   hands   on   the   wheel   so   that  
you

  are   ready   to   react   at   any   time   to  
any

  eventuality.
On
  a   long   journey,   a   break   every  
two hours

  is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,  
anticipate

  the   need   to   brake   and  
increase

  the   distance   from   other  
vehicles.
Driving on flooded roads
We strongly advise against driving
on  flooded   roads,   as   this   could   cause  
serious

  damage   to   the   engine   or  
gearbox, as well as to the electrical
systems

  of   your   vehicle. If you are obliged to drive through
water:
-
 
check
  that   the   depth   of   water   does  
not

  exceed   15   cm,   taking   account  
of

  waves   that   might   be   generated  
by other users,
-
 
deactivate
  the   Stop   &   Start   system,
-
drive as slowly as possible without
stallin

g.   In   all   cases,   do   not   exceed  6
  mph   (10   km/h),
- do not stop and do not switch of f
the
  engine.
On
  leaving   the   flooded   road,   as   soon  
as

  circumstances   allow,   make   several  
light

  brake   applications   to   dry   the   brake  
discs

  and   pads.
If in doubt on the state of your vehicle,
contact a CITR
o Ë n dealer or a
qualified
  workshop.Never
  drive   with   the   parking   brake  
applied

  -   Risk   of   overheating   and  
damage

  to   the   braking   system!
Do   not   park   or   run   the   engine   when  
stationary

  in   areas   where   inflammable  
substances

  and   materials   (dry   grass,  
dead

  leaves...)   might   come   into   contact  
with

  the   hot   exhaust   system   -   Risk   of  
fire!
n

ever leave a vehicle
unsupervised with the engine
running.   If   you   have   to   leave  
your vehicle with the engine running,
apply

  the   parking   brake   and   put   the  gearbox into neutral or position
N or P,
depending
  on   the   type   of   gearbox.
Important!
REadY To Go
3

 59
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
LED DAYTIME RUNNING LAMPS
Rear foglamps (amber, 
2nd rotation of the ring
forwards).
Front
  foglamps   (green,  
1st

rotation of the ring
forwards). Rotate this ring forwards
to switch on and
rearwards   to   switch   off.
Their   state   is   confirmed   by  
the

  warning   lamps   in   the  
instrument

  panel. Do   not   forget   to   switch   them   off  
when

  they   are   no   longer   needed.
Operation   of   the   automatic   illumination  
of

  headlamps   switches   off   the   rear  
foglamps,

  but   the   front   foglamps  
remain

  on.
To switch off the front and
rear   foglamps,   turn   the  
ring rearwards twice in
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the  sunshine   sensor   may   detect  
sufficient

  light.  
As
  a   consequence,  
the

 
lighting   will   not   come   on  
automatically

.
If
  necessary,   you   must   switch  
on

  the   dipped   beam   headlamps  
manually

.
d

o not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination   of   headlamps   and   for   the  
automatic

  rain   sensitive   wipers.
Activation
Turn the ring to the AUTO
  position.  
The activation of this function is
accompanied

  by   a   message   in   the  
screen.
Deactivation
T

urn
  the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied

  by   a   message   in   the  
screen.
The

 
function   is   deactivated   temporarily  
when

  you   use   the   manual   lighting  
control

  stalk. The
  sidelamps  
and

  dipped   beam  
headlamps

  switch  
on

  automatically   if  
the light is poor

, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light

  becomes   bright   enough   or   the  
windscreen

  wipers   stop.
This
  function   is   not   compatible   with   the  
daytime

  running   lamps.
o

n starting the vehicle, in daylight the
LED
 
daytime
 
running
 
lamps
 
come
 
on
 
automatically

.
If
 
the
 
sidelamps
 
and
 
headlamps
 
are
 
switched

 
on
 
manually
 
or
 
automatically,
 
the

 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day   is   not   a   legal   requirement,   you   can  
activate or deactivate the function via
the

  configuration   menu.
If the user does not operate any
equipment
 
for
 
30
 
minutes,
 
the
 
Economy

 
mode
 
engages
 
to
 
avoid
 
discharging

 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp
 
operation
 
is
 
not
 
affected
 
by
 
Economy

 
mode.
In clear weather or in rain, both day
and  night,   rear   foglamps   dazzle   and  
their

  use   is   prohibited.
Refer to chapter 8, "Battery
section".
Front and rear foglamps
They
 
operate
 
with
 
the
 
sidelamps
 
and
 
dipped

 
beam
 
headlamps.
Steering mounted controls
EASE OF USE and COMFORT
4

158
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Levels
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).

 165
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
AdBlue® additive
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Range indicators
Rules on the display of alertsFor   more   information   on   the  
displays

  and   warning   lamps,   refer  
to

  chapter   3,   "Instruments   and  
controls"

  section. Range greater than 1 500 miles
(2 400 km)
No
  information   displayed.
Once   the   1   500   miles   (2   400   km)  
threshold is reached, the URE

a

warning

  lamp   comes   on   temporarily  
and

  the   remaining   range   message   is  
displayed.
The

  alert   is   repeated   every   150   miles  
(300

  km)   until   the   next   threshold   is  
reached.
Every

  time   the   ignition   is   switched  
on, the alert is given, together with an
audible

  signal.
Remaining range less than
1 500 miles (2 400 km) and greater
than 350 miles (600 km)
Driving range
With
  the   touch   screen   tablet:
If
  the   range   is   greater   than   3   000   miles  
(5

  000   km),   a   range   value   is   not   given.
Press this button to display
the
  information.
-

select the "
d riving
assistance"
  menu,
-

select "
d iagnostic",
-
 
select
  CHECK.
d
ifferent levels of alert are triggered
according
  to   the   remaining   driving  
range

  threshold.
You
  will   be   informed   as   each   mileage  
threshold is reached and the alerts will
change

  from   temporary   to   permanent.
-

The 1st is triggered at a remaining driving
  range   of   1   500   miles  
(2
 
400
  km).
-
The 2nd is triggered at a remaining driving
  range   of   350   miles   (600 km).
-
 
Up

 
to
 
0   miles,   at   which   point   it   will  
be

 
impossible   to   restart   the   engine  
after

 
a
 
stop.
CHECKS
7

169
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
BATTERY
Before disconnecting the battery, you
must  wait   for   2   minutes   after   switching  
of

f   the   ignition.
Never
  disconnect   a   terminal   when   the  
engine

  is   running.
Never
  charge   a   battery   without   first  
disconnecting

  the   terminals.
a

fter every reconnection of the battery,
switch
  on   the   ignition   and   wait   1   minute  
before starting to allow the electronic
systems

  to   be   initialised.   If   problems  
remain

  after   doing   this,   please   contact  
a

  CITROËN   dealer   or   a   qualified  
workshop.
a

fter changing bulbs, wait
approximately
  3   minutes   before  
reconnecting

  the   battery.
It is advisable to disconnect the
battery if the vehicle is not to be
used

 
for
 
a
 
period
 
of
 
more
 
than
 
one month.
To charge the battery using a
battery charger
- Disconnect   the   battery.
-
Follow the instructions for use
given by the battery charger
manufacturer

.
-

Reconnect starting with the
negative

  (-)   terminal.
-
 
Check
  that   the   terminals   and  
connectors

  are   clean.   If   they   are  
covered with sulphate (white or
greenish

  deposit),   disconnect   them  
and

  clean   them.
To start the vehicle from
another battery
- Connect the red cable to the
positive  (+)   terminals   of   the  
two batteries.
-


Connect one end of the green
or

  black   cable   to   the   negative   (-)  
terminal

  of   the   slave   battery.
-

Connect the other end of the green
or

  black   cable   to   an   earth   point   on  
the

  broken   down   vehicle   as   far   as  
possible

  from   the   battery.
-
 Operate

  the   starter,   let   the   engine   run.
-

W
ait for the engine to return to idle,
then
  disconnect   the   cables.
The presence of this label
indicates the use of a 12 V
lead-acid battery with special
technology
 
and
 
specification,
 
for
 
which
 
the

 
involvement
 
of
 
a
 
CITROËN
 
dealer
 
or

 
qualified
 
workshop
 
is
 
required
 
when
 
replacing

 
or
 
disconnecting
 
the
 
battery.
Failure to observe this
recommendation
 
may
 
cause
 
premature
 wear
 
of
 
the
 
battery.
After
 
refitting
 
the
 
battery,
 
the
 
Stop &
 
Start

 
system
 
will
 
only
 
be
 
active
 
after
 
several hours depending on the
climatic

 
conditions
 
and
 
the
 
state
 
of
 
charge of the battery (up to about
8 hours).
The Stop & Start battery does not have
to

 
be
 
disconnected
 
for
 
charging.
Battery
QUICk HELP
8

170
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
ECONOMY MODE
after the engine has stopped, with
the   key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows,
  courtesy   lamps,   audio  
equipment,

  etc.)   can   only   be   used   for   a  
cumulative

  duration   of   thirty   minutes,   to  
prevent

  discharging   of   the   battery.
Once
  the   thirty   minutes   have   elapsed,  
the active functions are put on standby
and

  the   battery   warning   lamp   flashes  
accompanied

  by   a   message   in   the  
screen.
T

o   resume   the   use   of   these   functions  
immediately

,   start   the   engine   and   let   it  
run

  for   a   few   minutes.
The
  time   available   will   then   be   double  
the

  time   for   which   the   engine   was   left  
running.

  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery

198
Berlingo-2-VP_en_Chap09_Caract-technique_ed02-2015Berlingo-2-VP_en_Chap09_Caract-technique_ed02-2015
Diesel Engines / Weights
5-seatEngine Gearbox GearsEngine oil
capacity* (litres) Unbraked
trailer (kg) Recommended
nose
weight (kg)
1.6 HDi 75 hp Manual5-740 50
1.6 HDi 75 hp FAP Manual5-715 70
1.6 HDi 90 hp Manual53.75 740 55
1.6 HDi 90 hp FAP Manual53.75 750 55
1.6 HDi 92 hp ECO Manual53.75 715 70
1.6 HDi 92 hp FAP Manual53.75 715 70
1.6 e-HDi 92 hp ECO Manual
5
3.75 690
70
Electronic 6 75070
1.6 e-HDi 92 hp FAP Manual
5
3.75 690
70
Electronic 6 75070
1.6 HDi 110 hp FAP Manual53.75 750 55
1.6 HDi 112 hp FAP Manual53.75 735 70
FAP:
  particle   filter.
e-HDi:
 
model
  equipped   with   Stop   &   Start.
*
  Capacity   with   oil   filter   replacement.
Weights

 199
Berlingo-2-VP_en_Chap09_Caract-technique_ed02-2015Berlingo-2-VP_en_Chap09_Caract-technique_ed02-2015
7-seatEngine Gearbox GearsEngine oil
capacity* (litres) Unbraked
trailer (kg) Recommended
nose
weight (kg)
1.6 HDi 90 hp Manual53.75 750 70
1.6 HDi 90 hp FAP Manual53.75 750 70
1.6 HDi 92 hp FAP Manual53.75 750 70
1.6 e-HDi 92 hp FAP Manual53.75 750 70
1.6 HDi 110 hp FAP Manual53.75 750 70
1.6 HDi 112 hp FAP Manual53.75 750 70
FAP:
  particle   filter.
e-HDi:
 
model
  equipped   with   Stop   &   Start.
*
  Capacity   with   oil   filter   replacement.
TECHNICAL DATA
9
Weights

Audio and Telematics
 207
Berlingo-2-VP_en_Chap10a_SMEGplus_ed02-2015
Level 1Level 2 Level 3 Comments
Navigation Settings
Navigation Enter destination
Display
  recent   destinations.
Calculatory criteria Fastest
Choose
  the   navigation   criteria.
The
  map   displays   the   route   chosen   according   to  
t

hese
 c
riteria.
Shortest
Time/distance
Ecological
To l l s
Ferries
Tr a f f i c
Strict-Close
Show
  route   on   map Display   the   map   and   start   navigation.
Confirm Save
  the   options.
Save current location Save
  the   current   address.
Stop navigation Delete
  the   navigation   information.
Voice synthesis Choose
  the   volume   for   voice   and   announcement  
o

f   street   names.
Diversion Detour
  from   your   initial   route   by   a   determined  
di

stance.
Navigation Display
  in   text   mode.
Zoom
  in.
Zoom
  out.
Display
  in   full   screen   mode.
Use
  the   arrows   to   move   the   map.
Switch
  to   2D   map.
TECHNOLOGY on BOARD
10