remove seats Citroen BERLINGO MULTISPACE RHD 2015.5 2.G Owner's Manual

17
Motoring & the Environment
Berlingo-2-VP_en_Chap02_eco-conduite_ed02-2015
Limit the causes of excess consumption
Spread loads throughout the vehicle; place the heaviest
items  in   the   bottom   of   the   boot,   as   close   as   possible   to   the  
rear

  seats.
Limit
  the   loads   carried   in   the   vehicle   and   reduce   wind  
resistance

  (roof   bars,   roof   rack,   bicycle   carrier,   trailer...).  
Use

  a   roof   box   in   preference.
Remove
  roof   bars   and   roof   racks   after   use.
At
  the   end   of   winter,   remove   snow   tyres   and   refit   your  
summer

  tyres.
Observe the recommendations on maintenance
Check the tyre pressures regularly, when cold, referring to the  label   in   the   door   aperture,   driver's   side.
Carry
  out   this   check   in   particular:
-
 
before
  a   long   journey,
-

at each change of season,
-

 
after
  a   long   period   out   of   use.
d

on't forget the spare wheel and the tyres on any trailer or
caravan.
Have your vehicle serviced regularly (engine oil, oil
filter,
  air   filter,   passenger   compartment   filter...)   and  
observe

  the   schedule   of   operations   recommended   in   the  
manufacturer's

  service   schedule.
With
  a   BlueHDi   Diesel   engine,   if   the   SCR   system   is  
faulty

  your   vehicle   becomes   polluting;   go   to   a   CITROËN  
dealer

  or   a   qualified   workshop   without   delay   to   have   the  
emissions

  of   nitrous   oxides   brought   back   to   the   legal   level.
When refuelling, do not continue after the third cut-off of
the
  nozzle   to   avoid   any   overflow.
At
  the   wheel   of   your   new   vehicle,   it   is   only   after   the   first  
1

  800   miles   (3   000   kilometres)   that   you   will   see   the   fuel  
consumption

  settle   down   to   a   consistent   average.
2
ECO-DRIVING

78
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Seats
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
never drive with the head
restraints   removed;   they   must   be  
in

  place   and   correctly   adjusted.
Adjustable armrest
Front heated seats control
Each front seat may be fitted with a control located on the side part of the
cushion.
Press  to   switch   on   the   cushion   heating.
Press
  again   to   switch   it   off.
Head restraint height
To raise the head restraint, slide it vertically
upwards.
To lower the head restraint, press the
button and slide the head restraint
vertically  downwards.
The
  adjustment   is   correct   when   the   upper
 edge of the head restraint is level with the


top
  of   the   head.
To
  remove   the   head   restraint,   press   the
 button

  and   pull   the   head   restraint   upwards.
To re-install the head restraint, engage
the
  rods   in   the   holes   making   sure   they   are
 aligned

  with   the   seat   back.
To access the vertical position, raise
the  armrest   until   it   locks.
Lower
  the   armrest   to   return   it   to   a  
position

  for   use.
To
  remove   the   armrest,   press   the  
release

 
button
 
from
 
the
 
vertical
 
position
 
and

  move   aside   the   armrest.
To
  put   the   armrest   back   in   place,   clip   it  
in

  the   vertical   position.
If
  the   vehicle   is   fitted   with   the   additional  
console

  and   an   armrest,   to   fold   the  
passenger seat to the table position
remove

  the   console   or   the   armrest.

 79
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Seats
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
REAR BENCH SEAT
Each 1/3 - 2/3 section can be fully folded,  then   removed   individually.
Head restraint
The 1/3 - 2/3 split rear bench seat is fitted with  "comma"   shape   head   restraints.
High position: lift and raise the head restraint.
Low
  position:   press   on   the   head  
restraint

  to   lower   it.
To
  remove   the   head   restraint,   after  
raising it press the tab and lift the head
restraint.
T

o install the head restraint, engage
the rods of the head restraint in the
holes
  keeping   it   in   line   with   the   seat  
back.
EASE OF USE and COMFORT
4

82
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Seats
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
REAR SEATS (5 SEAT VERSION)Head restraint
Each seat can be removed individually.
Each   time   a   seat   is   returned   to   the  
sitting

  position   or   after   removing   then  
refitting

  a   seat,   check   that   it   is   locked  
on

  the   floor   securely.
The three independent rear seats
are
 
fitted
 
with
 
"comma"
 
shape
 
head
 
restraints.
The

 
back
 
of
 
the
 
centre
 
seat,
 
folded
 
onto
 the seat cushion, has a shell which


serves
 
as
 
a
 
table
 
with
 
cup
 
holder. High
  position:   lift   and   raise   the   head  
restraint.
Low

  position:   press   on   the   head  
restraint

  to   lower   it.
To   remove   the   head   restraint,   after  
raising it press the tab and lift the head
restraint.
T

o install the head restraint, engage
the rods of the head restraint in the
holes   keeping   it   in   line   with   the   seat  
back.

84
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Seats
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Removing the seat
- If  necessary,   move   the   front  seats forward and lower the head
restraint.
-

Place the seat in the fully folded
position.
Good practice
Following the various operations:
-  
do
  not   remove   a   head   restraint  
without

  storing   it   and   fix   it   to   a  
support,
-


ensure that the passengers can
always access the seat belts and
fasten

  them   easily,
-
 
passengers
  must   never   take  
their

  seat   without   adjusting   and  
fastening

  their   seat   belt.
Refer to the "Fully folded position"
described
 
previously.
-

Press the red lever to release the
front

 
feet.
-

T

ilt the entire seat rearwards by
approximately
 
45°
 
without
 
releasing
 
the

 
lever.
-
 
Release

 
the
 
lever.
-

Lift the seat

vertically
 
to
 
the
 
limit
 
of
 
the

 
anchorages.
-

Straighten the seat by tilting it
forwards

 
then
 
lift
 
it.
Refitting the seat
- Tilt   the   seat   forward   by   45°.
-  
Place
  the   hooks   between   the   two  
bars.
-

 
Fold
  back   the   seat   to   fix   the   rear  
anchoring

  points.
-

Pull the control to return the seat
back

  to   its   initial   position.
-
 
Raise
  the   head   restraint.
Before
  unfolding   the   seat,   check  
that

  no   object   is   obstructing   the  
anchorage points or preventing
correct

  locking   of   the   seats.

85
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Seats
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Head restraint
This is of the "comma" shape type.
High   position:   press   the   tab,   lift   and  
raise

  the   head   restraint.
Low
  position:   push   the   tab   and   press  
the

  top   of   the   head   restraint   to   lower   it.
To
  remove   the   head   restraint:   place   it   in
 the

  high   position,   lift   it,   then   remove   it.
Store it inside the vehicle, securing it
firmly.
To
  install   the   head   restraint:   engage  
the rods of the head restraint in the
holes

  keeping   it   in   line   with   the   seat  
back.
Each

 
seat
 
can
 
be
 
removed
 
and
 
must
 
be

 
replaced
 
in
 
the
 
specified
 
position,
 
indicated

 
by
 
a
 
symbol
 
on
 
its
 
label.
The seats of row 2 and row 3 are
independent
 
and
 
adjustable.
REAR SEATS (7 SEAT VERSION)
EaSE oF USE and CoMFoRT
4

 91
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Seats
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Operating the Row 3 seats
Removing the seat
- 
Lower
  the   head   restraint.
-

Place the seat in the fully folded
position.
-

 
T
ilt   the   entire   seat   forwards.
-
 
On
  each   side,   take   hold   of   the  
uprights of the folded seat, tilting it
forward

  slightly,   and   lift   it.Refitting the seat
The label on the seat indicates the
position
  in   which   it   must   be   installed.
-
 
Place
  the   hooks   of   the   front   feet  
between

  the   two   bars.
-
 
Ensure
  that   no   object   or   foot   is  
obstructing the rear anchorage
points and that the seat belt is
positioned correctly and available
for

  use.
-
 
Fold
  back   the   seat   to   fix   its   rear  
anchoring

  feet.
-
o perate the control to raise the
seat
  back   to   its   initial   position.
-
 
Raise
  the   head   restraint.
Good practice
Following the various operations:
-  
do
  not   remove   a   head   restraint  
without stowing it; secure it inside
the vehicle,
-


ensure that the passengers can
always access the seat belts and
fasten

  them   easily,
-
 
passengers
  must   never   take  
their

  seat   without   adjusting   and  
fastening

  their   seat   belt.
-
 
a
  passenger   seated   in   row   3   must  
ensure that he does not obstruct
the row 2 seat anchorage points,
-

 
a
  passenger   seated   in   row   3   must  
not

  have   the   seat   in   front   of   them   in  
row 2 in the folded position; this is
in case the seat could tip towards
the passenger unexpectedly and
injure

  them.
Do
  not   place   hard   or   heavy   objects   on  
the

  seat   backs   forming   a   table,   they  
could

  become   dangerous   projectiles   in  
the

  event   or   sharp   braking   or   impact.
EASE OF USE and COMFORT
4

104
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Automatic switching on/off
The front courtesy lamp comes on when the  key   is   removed   from   the   ignition,   when the

  vehicle   is   unlocked,   when   one   of   the
 front doors is opened and for location of


the
  vehicle   using   the   remote   control.
It goes off gradually after the ignition is
switched on and when the vehicle is
locked.Front seats: comes on when one of the front doors is
opened. These are switched on and of
f by
means   of   a   manual   switch,   with  
the

  ignition   on.
Rear
  seats:   comes   on   when  
one of the rear doors is
opened.
If

  the   doors   remain   open   for  
a

  few   minutes,   the   courtesy  
lamps

  go   off.
Permanently
  off.
Permanently
 
on,
 
ignition
 
on.
Front courtesy lamp
COURTESY
LAMPS
Rear courtesy lamp Front individual reading lamps
Practical information

105
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
LOAD SPACE COVER (5 SEAT VERSION)
This rigid shelf conceals the objects stored  in   the   boot. Removing
Fold
  the   load   space   cover.
Detach   it   from   the   notches   A and B
pulling
  it   towards   you.
Raise
  it   and   remove   the   assembly.
Refitting
Place the load space cover in front
of A and B.
Push it forwards to insert the lugs in
the
  notches.
Unfold and clip into the notches C.
Folding
From
  the   boot,   fold   the   half-shelf,  
raising

  it   to   detach   it   from   the   notch   C. Storing (according to version)
A 
location   is   provided   in   the   back   of   the  rear
  seats   to   accommodate   the   load  
space

  cover   folded   onto   itself.
Slide it vertically between the side
guides
  located   at   mid   seat   back   height.
Insert
  the   hinge   first,   with   the   free   flaps  
turned

  upwards.
This rigid load space cover can
form
  a   shelf.   However,   as   a   safety  
measure,

  do   not   place   objects  
on

  it   which   could   become   dangerous  
projectiles

  in   the   event   of   sharp   braking  
or

  rear   impact.
EaSE oF USE and CoMFoRT
4
Practical information

11 0
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
To remove it
From  the   boot,   pull   the   load   space  
cover

  towards   you   to   release   it   from  
the

  side   pillars.
Guide
  the   load   space   cover   as   it   rolls   up.
Remove
  the   clips   of   the   three   flaps  
from

  the   base   of   each   row   2   head  
restraint.
Compress

  the   roller   to   the   left   to  
remove

  it   from   the   support   B.
Raise
  it   and   pivot   it   forwards. To store it
Store it in the recess at the boot sill,
with
  the   two   rear   flaps   uppermost.
First,
  compress   the   load   space   screen  
to

  the   left.
Release.
Arrange
  the   two   flaps   and   close   the  
storage

  flap.
The
 
roller
 
is
 
fitted
 
with
 
three
 
flaps
 
permitting

 
concealment
 
of
 
the
 
boot, whether the row 2 seats
are

 
in
 
the
 
normal
 
position
 
or
 
the
 
comfort

 
position.
Each
 
flap
 
has
 
two
 
clips
 
which
 
are
 
hooked

 
on
 
the
 
base
 
of
 
each
 
head
 
restraint.
Practical information