dashboard Citroen BERLINGO MULTISPACE RHD 2016 2.G User Guide

 147
Berlingo-2-VP_en_Chap05_Securite_ed02-2015Berlingo-2-VP_en_Chap05_Securite_ed02-2015
CHILD LOCK
This prevents opening of the siding
side  doors   from   the   inside.
Manual Electric
With the ignition on, press
this
  button   in   the   middle   of  
the

  dashboard.
Indicator
  lamp   on   =   child   lock  
on.
Please

 
note:   this   system   is  
independent

  of   the   central   locking  
control.Always

  remove   the   ignition   key  
when leaving the vehicle, even for
a

 
short   time.
It
 
is
 
advisable   to   check   the   state   of  
the

 
child
 
lock   each   time   the   ignition   is  
switched

  on.
In
 
the
 
event   of   a   serious   impact   the  
electric

 
child   lock   is   deactivated  
automatically

.
a label indicates the position of the
lever

 
and
 
the
 
state
 
of
 
the
 
child
 
lock.
-
o
pen fully past the point of
resistance.
-

T

ilt the lever, located on the rear
section
 
of
 
the
 
door.
SaFETY
5
Child safety

154
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
OPENING THE BONNET
Bonnet stay
Secure the stay in its location,
identified  by   a   sticker   on   the   right-hand  
side of the vehicle, to hold the bonnet
open.
Before closing the bonnet, put the stay
back

  in   its   clip   without   using   excessive  
force.
On the outside
Raise the bonnet slightly by reaching
in  a   flat   hand,   palm   down,   to   make  
access

  to   the   lever   easier.
With this hand, push the safety catch
to
  the   left.   Raise   the   bonnet.
On the inside
Pull the lever below the dashboard
towards  you.  The   bonnet   is   released.
To close
Lower the bonnet and release it at the
end  of   its   travel.   Check   that   the   bonnet  
is

  secure.
avoid opening the bonnet in strong
winds.
opening the bonnet

158
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Levels
Berlingo-2-VP_en_Chap07_Verification_ed02-2015
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When
  the   engine   is   warm,   the  
temperature

  of   the   coolant   is   controlled  
by

  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and

  because   the   cooling   system   is  
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has

  dropped,   remove   the   cap   and   top  
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this

  indicates   a   fault   which   must   be  
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes
  as   soon   as   possible,   when  
traffic

  conditions   permit   (until   the  
message

  disappears   and   the   service  
warning

  lamp   goes   off).
d

uring regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating

  may   be   heard   under   the  
dashboard.
If

  the   message   is   still   displayed   and  
if

  the   service   warning   lamp   remains  
on, contact a CITR

o Ë n dealer or a
qualified
  workshop.
Topping up
The
 
level
 
must
 
be
 
between
 
the
 
MIN
 
and

 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash and headlamp
wash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For
  optimum   cleaning   and   to   avoid  
freezing,

  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
If
  your   vehicle   is   fitted   with   headlamp  
washers, the capacity of the reservoir
is

  6   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This   additive   must   be   topped   up   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
avoid prolonged contact of used oil
with   the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITR

o Ë n dealer (France) or
an
  authorised   waste   disposal   site.
The
 
minimum
 
level
 
of
 
this
 
additive
 
is indicated by lighting of the service
warning

 
lamp,
 
accompanied
 
by
 
an
 
audible

 
signal
 
and
 
a
 
message
 
in
 
the
 
screen.
When this occurs with the engine
running it is due to the start of
saturation

 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).

186
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
CHANGING A FUSE
The fuseboxes are located:
-
in the lower dashboard on the

left-hand side (behind the cover),
-
 
under
  the   bonnet   (near   the   battery).
The
  information   given   concerns   only  
those fuses which can be changed by
the user using the tweezer

, located
behind the dashboard storage
compartment
  on   the   right-hand   side.  
For

  any   other   work,   visit   a   CITROËN  
dealer

  or   a   qualified   workshop.
Removing and fitting a fuse
Always replace a failed fuse with a
fuse of the same rating.
Motor
 
trade
 
technicians:
 
for
 
complete

 
information
 
on
 
the
 
fuses
 
and relays, refer to the "Repair
Manual"

 
diagrams
 
via
 
the
 
dealer
 
network.
CITR

o
Ë
n
will not accept responsibility
for the cost incurred in repairing
your vehicle or for rectifying the
malfunctions
 
resulting
 
from
 
the
 installation of accessories not
supplied
 
and
 
not
 
recommended
 
by
 
the
 
CITROËN

 
network
 
and
 
not
 
installed
 
in accordance with its instructions,
in

 
particular
 
when
 
the
 
combined
 
consumption

 
of
 
all
 
of
 
the
 
additional
 
equipment

 
connected
 
exceeds
 

10
 
milliamperes. Before replacing a fuse, the cause of
the
  incident   must   be   identified   and  
rectified.
●

 
Use
  the   tweezer.
Changing a fuse

187
Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015Berlingo-2-VP_en_Chap08_aide-rapide_ed02-2015
Dashboard fuses
Tilt the cover to gain access to the
fuses.Fuses
F Amperes  
a a llocation
1 15 Rear wiper
2 -
n

ot used
3 5
a

irbag
4 10 Air
  conditioning,   diagnostic   socket,   mirror   control,  
headlamp

  beam
5 30 Electric windows
6 30Locks
7 5Rear
  courtesy   lamp,   front   map   reading   lamp,   roof  
console
8 20 Audio

  equipment,   screen,   tyre   under-inflation  
detection,

  alarm   and   siren
9 30Front
  and   rear   12V   socket
10 15 Central
  column
11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument
  panel
14 15 Parking
  sensors,   digital   air   conditioning   controls,  
hands-free

  phone   kit
15 30 Locks
16 -
n

ot used
17 40Rear
  screen/mirrors   demist/defrost
QUICk HELP
8
Changing a fuse

46
Instruments and controls






The new pressure settings registered
are considered to be reference values
by the system.



The under-infl ation alert is only
dependable if the system has
been reinitialised with all four tyres
infl ated to the correct pressures.

Before doing anything to the
system, the pressures of the four
tyres must be checked and the
system reinitialised.

Snow chains
The system does not have to be
reinitialised after fi tting or removing
snow chains.



Dashboard button


)
Make a long press on this button.
A high tone audible signal confi rms the
reinitialisation.
A low tone audible signal indicates that
the reinitialisation was not completed.



Operating fault

The fl ashing and then fi xed illumination
of the under-infl ation warning lamp
accompanied by illumination of the
Service warning lamp indicates a fault
with the system.
In this case, under-infl ation monitoring
of the tyres is no longer assured.
Have the system checked by a dealer
or a qualifi ed workshop.

CANCELS AND REPLACES






UNDER-INFLATION DETECTION
WITH REINITIALISATION