Citroen BERLINGO MULTISPACE RHD 2016 2.G Repair Manual

 59
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
LED DAYTIME RUNNING LAMPS
Rear foglamps (amber, 
2nd rotation of the ring
forwards).
Front
  foglamps   (green,  
1st

rotation of the ring
forwards). Rotate this ring forwards
to switch on and
rearwards   to   switch   off.
Their   state   is   confirmed   by  
the

  warning   lamps   in   the  
instrument

  panel. Do   not   forget   to   switch   them   off  
when

  they   are   no   longer   needed.
Operation   of   the   automatic   illumination  
of

  headlamps   switches   off   the   rear  
foglamps,

  but   the   front   foglamps  
remain

  on.
To switch off the front and
rear   foglamps,   turn   the  
ring rearwards twice in
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the  sunshine   sensor   may   detect  
sufficient

  light.  
As
  a   consequence,  
the

 
lighting   will   not   come   on  
automatically

.
If
  necessary,   you   must   switch  
on

  the   dipped   beam   headlamps  
manually

.
d

o not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination   of   headlamps   and   for   the  
automatic

  rain   sensitive   wipers.
Activation
Turn the ring to the AUTO
  position.  
The activation of this function is
accompanied

  by   a   message   in   the  
screen.
Deactivation
T

urn
  the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied

  by   a   message   in   the  
screen.
The

 
function   is   deactivated   temporarily  
when

  you   use   the   manual   lighting  
control

  stalk. The
  sidelamps  
and

  dipped   beam  
headlamps

  switch  
on

  automatically   if  
the light is poor

, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light

  becomes   bright   enough   or   the  
windscreen

  wipers   stop.
This
  function   is   not   compatible   with   the  
daytime

  running   lamps.
o

n starting the vehicle, in daylight the
LED
 
daytime
 
running
 
lamps
 
come
 
on
 
automatically

.
If
 
the
 
sidelamps
 
and
 
headlamps
 
are
 
switched

 
on
 
manually
 
or
 
automatically,
 
the

 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day   is   not   a   legal   requirement,   you   can  
activate or deactivate the function via
the

  configuration   menu.
If the user does not operate any
equipment
 
for
 
30
 
minutes,
 
the
 
Economy

 
mode
 
engages
 
to
 
avoid
 
discharging

 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp
 
operation
 
is
 
not
 
affected
 
by
 
Economy

 
mode.
In clear weather or in rain, both day
and  night,   rear   foglamps   dazzle   and  
their

  use   is   prohibited.
Refer to chapter 8, "Battery
section".
Front and rear foglamps
They
 
operate
 
with
 
the
 
sidelamps
 
and
 
dipped

 
beam
 
headlamps.
Steering mounted controls
EASE OF USE and COMFORT
4

60
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 With
 
the
 
ignition
 
off,
 
"flash"
 
the
 headlamps
 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manoeuvres...).
Cornering lighting
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Steering mounted controls

 61
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
2 Fast  wipe   (heavy   rain).
1  
Normal
  wipe   (moderate   rain).
l
 
Intermittent
  wipe.
0
 
Of
f.
â

Single wipe
 (press

  downwards).
In the Intermittent
  position,   the   wiping  
speed is in proportion to the vehicle
speed.
WIPERS
Manual wipingWhenever the ignition has been
switched  off   for   more   than   one   minute,  
with

  the   windscreen   wiper   stalk   in  
position

  2,   1   or   I,   the   stalk   must   be  
reactivated.
-

 
Move
  the   stalk   to   any   position.
-
 
Return
  it   to   the   desired   position.
d

o not cover the rain sensor,
located in the centre of the
windscreen,
  behind   the   mirror.Activation
Press
  the   control   downwards.  
a ctivation of the function is
accompanied   by   a   message   in   the  
screen.
Deactivation
Place

  the   windscreen   wipers   stalk   in  
position

I, 1 or 2.d
eactivation of the function is
accompanied   by   a   message   in   the  
screen.
In

  the   event   of   malfunction   of   the  
automatic

  windscreen   wipers,   the  
windscreen wipers will operate in
intermittent

  mode.
Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked. In the
AUTO position, the windscreen
wipers   operate   automatically   and  
adapt their speed to the intensity of the
rainfall.
When not in

AUTO   mode,   for   the  
other

  positions,   refer   to   the   manual  
windscreen

  wipers   section.
The   automatic   rain   sensitive  
windscreen

  wipers   function   must  
be

  reactivated   by   pressing   the   stalk  
downwards, if the ignition has been
switched

  off   for   more   than   one   minute.
When   using   an   automatic   car  
wash, switch of

f the ignition to
avoid
  triggering   the   automatic  
wiping.
In winter

, it is advisable to wait for the
windscreen
  to   completely   clear   of   ice  
before

  operating   the   automatic   wipers.
Automatic wipers
Steering mounted controls
EASE OF USE and COMFORT
4

62
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Screenwash and headlamp wash
Pull the stalk towards you, the wash-
wipe   is   accompanied   by   a   timed   sweep  
of

  the   wipers.
The
  headlamp   wash   is   linked   with   the  
wash-wipe, it is triggered if the dipped
headlamps

  are   on.
Turn
  the   ring   past   the   first  
position:

  the   rear   screenwash  
then the rear wiper operates
for

  a   fixed   time.
In winter, in the event of a
considerable
  amount   of   snow  
or ice, switch on the heated
rear

  screen.   Once   the   screen   is  
clear

,   remove   the   snow   or   ice   which  
has

  accumulated   on   the   rear   wiper  
blade.

 
Y
ou   can   then   operate   the   rear  
windscreen

  wiper.
To top up the levels, refer to the
"Levels"
  section   of   chapter   7.
Special position of the
windscreen wipers
In the minute following switching off of the ignition, any action on the
stalk
  positions   the   wipers   against   the  
windscreen

  uprights.
This action enables you to position
the
  wiper   blades   for   winter   parking,  
cleaning

  or   replacement.
Refer to the "Changing a windscreen
wiper
  blade"   section   of   chapter   8.
To
  park   the   wipers   in   their   normal  
position after this has been done,
switch

  on   the   ignition   and   move   the  
stalk. T

urn   the   ring   to   the   first  
position.
Rear wiperRear screenwash
Steering mounted controls

 63
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
TRIP COMPUTER
A

few definitions
Range: displays the distance which
can  travelled   with   the   remaining   fuel  
detected

  in   the   tank,   basd   on   the  
average

  consumption   over   the   last   few  
miles

  (kilometres).
This
  displayed   value   may   vary  
significantly

  following   a   change   in   the  
vehicle

  speed   or   the   relief   of   the   route.Current fuel consumption:
only
calculated and displayed above
20   mph   (30   km/h).
Average fuel consumption: this is the
average   fuel   consumption   since   the  
last

  trip   computer   zero   reset.
Distance travelled: calculated since
the   last   trip   computer   zero   reset.
Distance remaining to the
destination: calculated with reference to
the   final   destination,   entered   by   the   user.
 If guidance is activated, the navigation


system   calculates   it   as   a   current   value.
Average speed: this is the average
speed calculated since the last trip
computer
  zero   reset   (ignition   on).
Each press of the button, located at
the
 
end
 
of
 
the
 
wiper
 
stalk,
 
displays
 
the
 
dif

ferent
 
trip
 
computer
 
information
 
in
 
turn,

 
depending
 
on
 
the
 
screen.
When the required trip is displayed,
press  the   control   for   more   than  
two seconds. When
  the   range   falls   below   20   miles  
(30

  km),   dashes   are   displayed.  
After
 
fillin

g   with   at   least   10   litres   of   fuel,   the  
range is recalculated and is displayed
when

  it   exceeds   60   miles   (100   km).
If, whilst driving, dashes are displayed
continuously in place of the digits,
contact   a   CITROËN   dealer.
The "vehicle" tab with the range,
current
 
fuel
 
consumption
 
and
 
the
 remaining
 
distance
 
to
 
run.
The "1" tab (trip 1) with the average
speed,
 
the
 
average
 
fuel
 
consumption
 
and the distance travelled in trip

"1".
The
 
"2"
 
tab
 
(trip
 
2)
 
with
 
the
 
same
 
information

 
for
 
a
 
2
nd trip.
Reset
Steering mounted controls
EASE OF USE and COMFORT
4

64
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
CRUISE CONTROL
"CRUISE"
"This is the speed at which the driver
wishes  to   drive".
This
  aid   to   driving   in   free-flowing  
traffic

  enables   the   vehicle   to   maintain  
the

  speed   programmed   by   the   driver,  
unless

  a   steep   gradient   makes   this  
impossible.
For

  the   system   to   be   programmed   or  
activated,

  the   vehicle   speed   must   be  
greater

  than   25   mph   (40   km/h)   with  
4th gear

  or   higher   engaged. The
  state   of   the   cruise   control   system  
can

  be   seen   in   the   instrument   panel  
together

  with   the   the   programmed  
speed

  setting.
Function selected,
display of the "Cruise
Control"   symbol.
Function off,
OFF
Function   on.
Vehicle speed above,
the   programmed  
speed

  flashes.
o

perating fault
detected,
OFF - the dashes
flash.
1.
 Cruise
 
control
 
mode
 
On
 
/
 
Off.
2.
 
Reduce

 
cruise
 
speed
 
setting.
3.
 
Increase

 
cruise
 
speed
 
setting.
4.
 
Pause

 
/
 
Resume
 
cruise
 
control.
Steering mounted controls

 65
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Selecting the functionFirst activation /
Programming a
speed Temporarily exceeding the
speed setting
Deactivation (off)
- Press this button or
the  brake   or   clutch  
pedal.
Reactivation
- Following deactivation of the cruise
control,  press   this   button.
Your vehicle will return to the last
programmed
  speed.
Alternatively,
  you   can   repeat   the   "first  
activation"

  procedure.
It is possible to accelerate and drive
momentarily
 
at
 
a
 
speed
 
greater
 
than
 
the

 
programmed
 
speed
 
setting.
 
The

 
value

 
programmed
 
flashes.
When the accelerator pedal is
released, the vehicle will return to the
programmed
 
speed.
-

Reach the chosen speed by
pressing

 
the
 
accelerator.
-

Press the

SET - or SET +
 
button.
This
 
programmes/activates
 
the
 
speed
 
setting

 
and
 
the
 
vehicle
 
will
 
maintain
 
this

 
speed.
-

Place the switch in the

CRUISE
position.
 
The

 
cruise
 
control
 
is
 
selected but is not yet active and
no

 
speed
 
has
 
been
 
programmed.
Steering mounted controls
EASE OF USE and COMFORT
4

66
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Changing the
programmed speedSwitching the system off
Operating fault Cancelling the programmed
speed setting
When the vehicle becomes stationary, after switching of
f the ignition, the
system
  no   longer   memorises   a   speed.
There
 
are
 
two
 
methods
 
of
 
memorising
 
a speed

higher
 
than
 
the
 
previous
 
one:
-
Place the dial in position
0 or switch
off the ignition to switch everything
off.
Good practice
Without using the accelerator
-

Press the
SET +   button.
A brief   press   increases   the   speed   by   1   mph   (km/h).
A maintained   press   increases   the   speed   in steps
  of   5   mph   (km/h).
Using the accelerator
-
 
Exceed
  the   memorised   speed   until  
the speed required is reached,
-


Press the
SET + or SET -   button.
To
  memorise   a   speed   lower than the
previous
  one:
-

Press the
SET -   button.
a brief press decreases the speed by


1
  mph   (km/h).
A
 

maintained   press   decreases   the  
speed

  in   steps   of   5   mph   (km/h).The
  programmed   speed   setting   is  
cleared

  and   replaced   by   three   dashes.  
Contact a CITR

o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked.When

  changing   the   programmed  
speed

  setting   by   means   of   a  
maintained

  press,   pay   attention   as  
the speed can increase or decrease
rapidly

.
d

o not use the cruise control on
slippery   roads   or   in   heavy   traffic.
In the event of a steep slope, the cruise
control   cannot   prevent   the   vehicle   from  
exceeding

  the   programmed   speed  
setting.
In any event, the cruise control cannot
replace the need to observe the speed
limits

  and   the   need   for   vigilance   on   the  
part

  of   the   driver.
It   is   advisable   to   keep   your   feet   near  
the

  pedals.
To   avoid   any   jamming   under   the  
pedals:
-

 
ensure
  that   the   mat   and   its   fixings  
on

  the   floor   are   positioned   correctly,
-  
never
  place   one   mat   on   top   of  another
.
Steering mounted controls

 67
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
The speed of the vehicle responds to
the pressure of the driver's foot, up
to the the accelerator pedal's point of
resistance, which indicates that the
programmed  speed   has   been   reached.
However, pressing the pedal beyond
this
  point   of   resistance   to   the   floor  
allows

  the   programmed   speed   to   be  
exceeded.

 
T
o   resume   use   of   the   limiter,  
simply

  reduce   the   pressure   on   the  
accelerator pedal gradually and return
to

  a   speed   below   that   programmed.
Adjustments can be carried out
when stationary, with the engine
running, or with the vehicle moving. This
  speed   limiter   shows   the   function  
selection

  status   in   the   instrument   panel  
and

  displays   the   programmed   speed:SPEED LIMITER
"LIMIT"
Function selected,
displaying of the
"Speed
  Limiter"  
symbol.
Function of

f,
last
  programmed  
speed -

OFF.
Function
  on.
Vehicle speed above,
the
  programmed  
speed setting is
displayed

  flashing.
o

perating fault
detected,
OFF - the dashes
flash.
1.
 
Limiter

 
mode
 
On
 
/
 
Off.
2.
 
Reduce

 
programmed
 
speed
 
setting.
3.

 
Increase

 
programmed
 
speed
 
setting.
4.

 
Speed

 
limiter
 
On
 
/
 
Pause.
"This is the selected speed which the
driver
 
does
 
not
 
wish
 
to
 
exceed".
This
 
selection
 
is
 
made
 
with
 
the
 
engine
 running while stationary or with the vehicle


moving.
 
The

 
minimum
 
speed
 
which
 
can
 be

 
programmed
 
is
 
20
 
mph
 
(30
 
km/h).
Steering mounted controls
EaSE oF USE and CoMFoRT
4

68
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Selecting the functionProgramming a speed setting On / Off
- Place the switch in the LIMIT
position.  The   limiter   is   selected  
but

  is   not   yet   active.  
The
  screen  
indicates

  the   last   programmed  
speed

  setting.
A
 

speed   can   be   programmed   without  
activating

  the   limiter   but   with   the  
engine

  running.
To
  memorise   a   speed   higher than the
previous
  one:
-

Press the
SET +   button.
A brief   press   increases   the   speed   by   1 mph   (km/h).
A
 
maintained   press   increases   the   speed   in   steps   of
 5

  mph   (km/h).
To memorise a speed lower than the
previous   one.
-

Press the
SET -   button.
A brief   press   decreases   the   speed   by   1   mph   (km/h).
A
 
maintained   press   decreases   the   speed   in   steps   of
 5

  mph   (km/h).
Pressing this button once activates
the  limiter,   pressing   the   button   again  
deactivates it

(OFF).
Steering mounted controls