fuel consumption Citroen BERLINGO MULTISPACE RHD 2016 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2016, Model line: BERLINGO MULTISPACE RHD, Model: Citroen BERLINGO MULTISPACE RHD 2016 2.GPages: 296, PDF Size: 11.04 MB
Page 18 of 296

16
Motoring & the Environment
Berlingo-2-VP_en_Chap02_eco-conduite_ed02-2015
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and Co
2Â emissions.
Eco-driving
Optimise the use of your gearbox
With a manual gearbox, move off gently and change up without  waiting.  During  acceleration  change  up  early.
With
 an  automatic  or  electronic  gearbox,  give  preference Â
to
 automatic  mode  and  avoid  pressing  the  accelerator Â
pedal
 heavily  or  suddenly.
The
 gear  shift  indicator  invites  you  engage  the  most Â
suitable
 gear:  as  soon  as  the  indication  is  displayed  in  the Â
instrument
 panel,  follow  it  straight  away.
For
 vehicles  fitted  with  an  electronic  or  automatic  gearbox, Â
this
 indicator  appears  only  in  manual  mode.
Drive smoothly
Maintain a safe distance between vehicles, use engine
braking rather  than  the  brake  pedal,  and  press  the Â
accelerator
 progressively. Â
These
 practices  contribute Â
towards
Â
a
Â
reduction
Â
in
Â
fuel
Â
consumption
Â
and
Â
CO2 emissions and
Â
also
Â
helps
Â
reduce
Â
the
Â
background
Â
traffic
Â
noise.
If your vehicle has cruise control, make use of the system at  speeds  above  25  mph  (40  km/h)  when  the  traffic  is Â
flowing
 well.
Control the use of your electrical
equipment
Before moving off, if the passenger compartment is too warm, ventilate  it  by  opening  the  windows  and  air  vents Â
before
 using  the  air  conditioning.
Above
 30  mph  (50  km/h),  close  the  windows  and  leave  the Â
air
 vents  open.
Remember
 to  make  use  of  equipment  that  can  help  keep Â
the
 temperature  in  the  passenger  compartment  down Â
(sunroof
 and  window  blinds...).
Switch
 off  the  air  conditioning,  unless  it  has  automatic Â
regulation,
 as  soon  as  the  desired  temperature  is  attained.
Switch
 off  the  demisting  and  defrosting  controls,  if  not Â
automatic.
Switch
 off  the  heated  seat  as  soon  as  possible.
Switch
 off  the  headlamps  and  front  foglamps  when  the Â
level
 of  light  does  not  require  their  use.
Avoid
 running  the  engine  before  moving  off,  particularly  in Â
winter;
 your  vehicle  will  warm  up  much  faster  while  driving.
As
 a  passenger,  if  you  avoid  connecting  your  multimedia Â
devices
 (film,  music,  video  game...),  you  will  contribute Â
towards
 limiting  the  consumption  of  electrical  energy,  and Â
so
 of  fuel.
Disconnect
 your  portable  devices  before  leaving  the  vehicle.
Page 19 of 296

17
Motoring & the Environment
Berlingo-2-VP_en_Chap02_eco-conduite_ed02-2015
Limit the causes of excess consumption
Spread loads throughout the vehicle; place the heaviest
items in  the  bottom  of  the  boot,  as  close  as  possible  to  the Â
rear
 seats.
Limit
 the  loads  carried  in  the  vehicle  and  reduce  wind Â
resistance
 (roof  bars,  roof  rack,  bicycle  carrier,  trailer...). Â
Use
 a  roof  box  in  preference.
Remove
 roof  bars  and  roof  racks  after  use.
At
 the  end  of  winter,  remove  snow  tyres  and  refit  your Â
summer
 tyres.
Observe the recommendations on maintenance
Check the tyre pressures regularly, when cold, referring to the label  in  the  door  aperture,  driver's  side.
Carry
 out  this  check  in  particular:
-
Â
before
 a  long  journey,
-
at each change of season,
-
Â
after
 a  long  period  out  of  use.
d
on't forget the spare wheel and the tyres on any trailer or
caravan.
Have your vehicle serviced regularly (engine oil, oil
filter,
 air  filter,  passenger  compartment  filter...)  and Â
observe
 the  schedule  of  operations  recommended  in  the Â
manufacturer's
 service  schedule.
With
 a  BlueHDi  Diesel  engine,  if  the  SCR  system  is Â
faulty
 your  vehicle  becomes  polluting;  go  to  a  CITROËN Â
dealer
 or  a  qualified  workshop  without  delay  to  have  the Â
emissions
 of  nitrous  oxides  brought  back  to  the  legal  level.
When refuelling, do not continue after the third cut-off of
the
 nozzle  to  avoid  any  overflow.
At
 the  wheel  of  your  new  vehicle,  it  is  only  after  the  first Â
1
 800  miles  (3  000  kilometres)  that  you  will  see  the  fuel Â
consumption
 settle  down  to  a  consistent  average.
2
ECO-DRIVING
Page 39 of 296

37
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Warning lamp in the
screenis
indicates Solution - action
Cruise
control on.
cruise
 control  selected.Manual
 selection.
Chapter
 4,  "Steering  mounted  controls"  section.
Speed limiter on.speed
 limiter  selected.Manual
 selection.
Chapter
 4,  "Steering  mounted  controls"  section.
Gear shift
indicator on.a
 recommendation Â
independent of the type and
density
 of  traffic.To
 reduce  fuel  consumption,  change  to  an Â
appropriate
 gear  with  a  manual  gearbox.
The driver retains responsibility to follow this
indication
 or  not.
Diesel pre-
heating on.climatic
 conditions  requiring Â
pre-heating.W
ait  until  the  warning  lamp  goes  off  before Â
operating
 the  starter.
Presence of
water in the
Diesel filter
on and
accompanied by
 a  message  in
 the
 screen.
water in the Diesel filter. Have  the  filter  bled  by  a  CITROËN  dealer  or  a  qualified
 workshop  without  delay.
Chapter  7,  "Checks"  section.
According
 to  country.
Service
spanner on.that a service will be due
shortly. Refer
 to  the  list  of  checks  in  the  maintenance  and Â
warranty
 guide.
Have the service carried out by a CITR
o Ë n
dealer
 or  a  qualified  workshop.
Time flashing. adjustment
 of  the  time.Use
 the  left-hand  button  on  the  instrument  panel.
Chapter
 3,  "Instruments  and  controls"  section.
REadY To Go
3
Page 43 of 296

41
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
EMISSIONS CONTROLS
EoBd (European on Board diagnosis) is a diagnostics
system
 which  complies Â
with,
 among  others,  the Â
standards on the authorised
emissions of:
-
Â
CO
Â
(carbon  monoxide),
-
HC (unburnt hydrocarbons),
-
no
x (nitrous oxides) or particles,
detected by oxygen sensors placed
upstream
 and  downstream  of  the Â
catalytic
 converters.
The
Â
driver
Â
is
Â
warned
Â
of
Â
any
Â
malfunction
Â
of
Â
this
Â
emission  control  system  by  the Â
illu
mination  of  this  specific  warning Â
lamp
Â
in
Â
the  instrument  panel.
There
Â
is
Â
a  risk  of  damage  to  the Â
catalytic
Â
converter.  Have  it  checked Â
by
Â
a
Â
CITROËN  dealer  or  a  qualified Â
workshop.
UNDER-INFLATION DETECTION
This system continuously monitors Â
the pressures of the four
tyres, as soon as the
vehicle
 is  moving.
a pressure sensor is located in the
valve of each tyre (except the spare
wheel).
The
Â
system
Â
triggers  an  alert  if  a  drop Â
in
Â
pressure
Â
is
Â
detected  in  one  or  more Â
tyres.The
Â
tyre
Â
under-inflation  detection Â
system
Â
is
Â
an  aid  to  driving  which Â
does not replace the need for
vigilance
Â
on  the  part  of  the  driver.This
 system  does  not  avoid  the  need
 to  check  the  tyre  pressures Â
regularly (including the spare
wheel)
 and  before  a  long  journey.
Driving
 with  under-inflated  tyres Â
adversely af
fects road holding,
extends
 braking  distances  and  causes Â
premature
 tyre  wear,  particularly  under Â
arduous conditions (vehicle loaded,
high
 speed,  long  journey).
Driving
 with  under-inflated  tyres Â
increases
 fuel  consumption.
The tyre pressures for your vehicle
can be found on the tyre pressure
label.
Refer
 to  chapter  9,  "Identification Â
markings"
 section.
The
 tyre  pressures  must  be  checked Â
when the tyres cold (vehicle stopped
for 1 hour or after driving for less then
6
 miles  (10  km)  at  moderate  speed).
Otherwise,
 add  0.3  bar  to  the  values Â
indicated
 on  the  label.
REadY To Go
3
Page 45 of 296

43
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
UNDER-INFLATION DETECTION WITH REINITIALISATION
System which automatically checks the pressures of  the  tyres  while  driving.
The
 system  monitors  the  pressures Â
in the four tyres, once the vehicle is
moving.
It
 compares  the  information  given  by Â
the four wheel speed sensors with
reference values, which must be
reinitialised every time the tyre
pressures are adjusted or a wheel
changed
.
The
 system  triggers  an  alert  as  soon Â
as
 it  detects  a  drop  in  the  inflation Â
pressure
 of  one  or  more  tyres. The  under-inflation  detection  system
 does  not  replace  the  need Â
for vigilance on the part of the
driver
.
This
 system  does  not  avoid  the  need  to Â
check
 the  tyre  pressures  (including  the Â
spare
 wheel)  every  month  as  well  as Â
before
 a  long  journey.
Driving
 with  under-inflated  tyres Â
impairs
 road  holding,  extends  braking Â
distances
 and  causes  premature Â
tyre wear
, particularly under arduous
condition (high loading, high speed,
long
 journey).
Driving
 with  under-inflated  tyres Â
increases
 fuel  consumption.The
 inflation  pressures  defined  for  your vehicle can be found on the
tyre
 pressure  label.
For
 more  information  on  the Â
identification
 markings,  refer  to  the Â
corresponding
 section.
Tyre
 pressures  should  be  checked Â
when the tyres are "cold" (vehicle
stopped
 for  1  hour  or  after  a  journey  of Â
less
 than  6  miles  (10  km)  at  moderate Â
speeds).
Otherwise
 (when  hot),  add  0.3  bar  to Â
the
 pressures  shown  on  the  label.
REadY To Go
3
Page 52 of 296

50
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
The information appears in the instrument  panel  in  the Â
form
 of  an  arrow.
The
 system  adapts  its  gear Â
change
 recommendation Â
according to the driving conditions
(slope,
Â
load, ...)  and  the  demands Â
of the driver (power
, acceleration,
braking, ...).
The
Â
system  never  suggests:
-
Â
engaging
 first  gear,
-
Â
engaging
 reverse  gear.
With
Â
an
Â
electronic
Â
gearbox,
Â
the
Â
system
Â
is
Â
only
Â
active
Â
in
Â
manual
Â
mode.
GEAR SHIFT INDICATOR
System which reduces fuel consumption  by  recommending  the Â
most
 appropriate  gear.
Operation
depending on the driving situation and
your  vehicle's  equipment,  the  system Â
may
 advise  you  to  skip  one  (or  more) Â
gear(s).
Â
Y
ou  can  follow  this  instruction Â
without
 engaging  the  intermediate Â
gears.
The
 gear  engagement Â
recommendations
 must  not  be Â
considered
 compulsory.  In  fact,  the Â
configuration
 of  the  road,  the  amount Â
of
 traffic  and  safety  remain  determining Â
factors when choosing the best
gear
. Â
Therefore,
 the  driver  remains Â
responsible for deciding whether or
not to follow the advice given by the
system.
This
 function  cannot  be  deactivated.
Gearbox and steering wheel
Page 54 of 296

52
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Acceleration
For optimum acceleration (e.g. to overtake another  vehicle),  simply Â
press the pedal beyond the point of
resistance at the end of its travel, by
pressing
 down  firmly.
Vehicle stationary, with the
engine running
In the event of a prolonged stop with
the engine running, the gearbox
changes automatically  to  neutral  N.
Stopping the vehicle
Before stopping the engine, put the
gear selector in position N.
In all cases, it is essential to apply
the
 parking  brake.  Check  that  the Â
parking
 brake  warning  lamp  is  on  in  the Â
instrument
 panel.
Before doing anything in the
engine
 compartment,  check  that Â
the gear selector is in neutral
N.
Changing gear
In situations of high engine speeds
(heavy acceleration), a change
up will not occur unless the driver
operates the electronic gearbox control
paddle. Pull on the "+" control
paddle
 to  change  up.
Pull on the "-" control
paddle to change
down.
-
If the vehicle stops or reduces
speed
 (for  example  when Â
approaching a stop sign),
the gearbox changes down
automatically
,  to  first  gear  if Â
needed.
-
It is not necessary to release the
accelerator
 completely  during  gear Â
changes.
-
a
gear change instruction is
accepted only if the engine speed
permits.
-
For safety reasons, depending on
the engine speed, a change down
may
 be  performed  automatically.
Manual mode
Changing to manual mode
Move the gear selector to M. Automatic mode Changing to automatic
mode
Move the gear selector to A.
The gearbox then operates in
automatic
Â
mode,
Â
without
Â
any
Â
action
Â
on
Â
your
Â
part.
It constantly selects the gear that is
best
Â
suited
Â
to
Â
the
Â
following
Â
conditions:
-
driving style,
-
Â
road
Â
profile,
-
Â
optimum
Â
fuel
Â
consumption.
Gearbox and steering wheel
Page 55 of 296

53
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
STOP & START
The Stop & Start system puts the engine
 temporarily  on  standby  -  STOP mode
 -  during  stops  in  the  traffic  (red Â
lights,
 traffic  jams,  or  other...). Â
The
Â
engine
 restarts  automatically  -  START
 mode
 -  as  soon  as  you  want  to  move Â
of
f. Â
The
 restart  takes  place  instantly, Â
quickly
 and  silently.
Perfect for urban use, the Stop & Start
system
 reduces  fuel  consumption  and Â
exhaust
 emissions  as  well  as  the  noise Â
level
 when  stationary.
Operation
Going into engine STOP mode
The "ECO"  warning  lamp  comes on
 in  the  instrument  panel  and the
 engine  goes  into  standby:
- with a manual gearbox , at speeds
below  12  mph  (20  km/h),  when  you Â
put the gear lever into neutral and
release the clutch pedal,
-
with
a 6-speed electronic
gearbox,
 at  speeds  below  5  mph Â
(8
 km/h),  when  you  press  the  brake Â
pedal or put the gear lever into
position
N. If
 your  vehicle  is  fitted  with  the  system, Â
a
 time  counter  calculates  the  sum  of Â
the
 periods  in  STOP
Â
mode  during  a Â
journey
.  It  rests  itself  to  zero  every  time Â
the
 ignition  is  switched  on  with  the  key.
With  a  6-speed  electronic Â
gearbox,
 for  your  comfort  during Â
parking
 manoeuvres,  STOP
Â
mode Â
is not available for a few seconds after
coming
 out  of  reverse  gear.
STOP
Â
mode  does  not  affect  the Â
functionality of the vehicle, such as
braking,
 power  steering,  for  example.
n
ever refuel with the engine in
STOP
Â
mode;  you  must  switch  off Â
the
 ignition  with  the  key.Special cases: STOP mode
unavailable
STOP
Â
mode  is  not  invoked  when:
-
the driver's door is open,
-
the driver's seat belt is not
fastened,
-
the vehicle has not exceeded
6Â mph
 (10  km/h)  since  the  last Â
engine
 start  using  the  key,
- Â
the
 engine  is  needed  to  maintain Â
a
 comfortable  temperature  in  the Â
passenger
 compartment,
- Â
demisting
 is  on,
- Â
some
 special  conditions  (battery Â
charge,
 engine  temperature, Â
braking
 assistance,  ambient Â
temperature...)
 where  the  engine Â
is needed to assure control of a
system.
In this case, the
"ECO"
warning  lamp  flashes  for  a Â
few
 seconds,  then  goes  off.
This operation is perfectly normal.
REadY To Go
3
Stop & Start
Page 65 of 296

 63
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
TRIP COMPUTER
A
few definitions
Range: displays the distance which
can travelled  with  the  remaining  fuel Â
detected
 in  the  tank,  basd  on  the Â
average
 consumption  over  the  last  few Â
miles
 (kilometres).
This
 displayed  value  may  vary Â
significantly
 following  a  change  in  the Â
vehicle
 speed  or  the  relief  of  the  route.Current fuel consumption:
only
calculated and displayed above
20  mph  (30  km/h).
Average fuel consumption: this is the
average  fuel  consumption  since  the Â
last
 trip  computer  zero  reset.
Distance travelled: calculated since
the  last  trip  computer  zero  reset.
Distance remaining to the
destination: calculated with reference to
the  final  destination,  entered  by  the  user.
 If guidance is activated, the navigation
system  calculates  it  as  a  current  value.
Average speed: this is the average
speed calculated since the last trip
computer
 zero  reset  (ignition  on).
Each press of the button, located at
the
Â
end
Â
of
Â
the
Â
wiper
Â
stalk,
Â
displays
Â
the
Â
dif
ferent
Â
trip
Â
computer
Â
information
Â
in
Â
turn,
Â
depending
Â
on
Â
the
Â
screen.
When the required trip is displayed,
press the  control  for  more  than Â
two seconds. When
 the  range  falls  below  20  miles Â
(30
 km),  dashes  are  displayed. Â
After
Â
fillin
g  with  at  least  10  litres  of  fuel,  the Â
range is recalculated and is displayed
when
 it  exceeds  60  miles  (100  km).
If, whilst driving, dashes are displayed
continuously in place of the digits,
contact  a  CITROËN  dealer.
The "vehicle" tab with the range,
current
Â
fuel
Â
consumption
Â
and
Â
the
 remaining
Â
distance
Â
to
Â
run.
The "1" tab (trip 1) with the average
speed,
Â
the
Â
average
Â
fuel
Â
consumption
Â
and the distance travelled in trip
"1".
The
Â
"2"
Â
tab
Â
(trip
Â
2)
Â
with
Â
the
Â
same
Â
information
Â
for
Â
a
Â
2
nd trip.
Reset
Steering mounted controls
EASE OF USE and COMFORT
4
Page 239 of 296

Audio and Telematics
 237
Berlingo-2-VP_en_Chap10a_SMEGplus_ed02-2015
Level 1Level 2 Comments
Settings
Secondary page System settings Units
Set the units used to display distance, fuel
consumption
 and  temperature.
Delete data Select the desired data in the list then press
Delete.
Factory settings Return
 to  factory  settings.
Confirm Save
 the  settings.
Settings
Secondary page Time/Date Confirm
Set
 the  date  and  time  then  confirm.
Settings
Secondary page Screen settings Activate automatic text scrolling
Activate
 or  deactivate  the  setting  then  confirm.
Activate animations
Confirm
TECHNOLOGY on BOARD
10