key Citroen BERLINGO MULTISPACE RHD 2017 2.G Owner's Guide

158
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Cooling system
Only use the fluid recommended by the manufacturer.
Otherwise,
  you   risk   seriously   damaging  
your

  engine.
When the engine is warm, the
temperature of the coolant is controlled
by
  the   engine   fan.  
As
  this   fan   can  
operate

  with   the   ignition   key   removed  
and because the cooling system is
pressurised, wait for at least one hour
after the engine has stopped before
carrying

  out   any   work.
Slacken
  the   cap   by   1/4   of   a   turn   to  
release the pressure to prevent any
risk

  of   scalding.   When   the   pressure  
has dropped, remove the cap and top
up

  the   level   with   coolant.
If
  fluid   has   to   be   added   frequently,  
this indicates a fault which must be
checked

  by   a   CITROËN   dealer   as  
soon

  as   possible.
Power steering fluid level
The vehicle must be parked on level ground  with   the   engine   cold.   Unscrew  
the cap integrated with the gauge and
check

  the   level   which   must   be   between  
the

  MIN   and   MAX   marks. In
  order   to   regenerate   the   filter,   you  are advised to drive at a speed higher
than
  40   mph   (60   km/h)   for   at   least   five  minutes as soon as possible, when
traffic
  conditions   permit   (until   the  
message disappears and the service
warning

  lamp   goes   off).
During regeneration of the particle
emission
  filter,   the   noise   of   a   relay  
operating may be heard under the
dashboard.
If the message is still displayed and
if the service warning lamp remains
on, contact a CITROËN dealer or a
qualified

  workshop.
Topping up
The level must be between the MIN
and
 
MAX
 
marks
 
on
 
the
 
expansion
 
bottle.

 
If
 
more
 
than
 
1
 
litre
 
of
 
fluid
 
is
 
required to top up the level, have the
system

 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
Screenwash level
For best quality cleaning and for your
safety, we would advise that you use
products   of   the   CITROËN   range.
For optimum cleaning and to avoid
freezing,
  this   fluid   must   not   be   topped  
up

  or   replaced   with   plain   water.
Capacity
  of   the   screenwash   reservoir:  
approximately

  3   litres.
Diesel additive level
(Diesel with particle
filter)
Topping up
This additive must be topped up by
a  CITROËN   dealer   or   a   qualified  
workshop

  without   delay.
Waste products
Avoid prolonged contact of used oil
with  the   skin.
Brake
  fluid   is   harmful   to   health   and  
very

  corrosive.
Do
  not   dispose   of   used   oil,   brake   fluid  
or coolant into drains or into the ground
but into the containers dedicated to this
use at a CITROËN dealer (France) or
an

  authorised   waste   disposal   site.
The minimum level of this additive
is indicated by lighting of the service
warning lamp, accompanied by an
audible signal and a message in the
screen.
When this occurs with the engine
running it is due to the start of
saturation
 
of
 
the
 
particle
 
filter
 
(exceptionally prolonged urban type
driving

 
conditions:
 
low
 
speed,
 
long
 
traffic

 
jams,
 
...).
Levels

161
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
REFUELLING
Low fuel level
Filling
The  fuel   tank   must   be   filled   with the
engine off.
-
 
Open
  the   fuel   filler   flap.
-
 
Insert
  the   key,   then   turn   it   a   quarter  
turn.
-

 
Remove
  the   cap   and   hook   it   onto  
the clip located on the inside of the
flap. When

  filling   with   fuel,  a
mechanical system prevents
opening
  of   the   left-hand   side   door.  
When

  the   fuel   filler   flap   is   open,   ensure  
that

  no   one   tries   to   slide   this   door.
Once
  the   flap   has   been   closed,   the  
sliding

  side   door   may   jam,   push   the  
door

  to   close   it   then   open   it.
When the low fuel level is
reached, this warning lamp
comes
 
on. A
 

label   affixed   to   the   inside   of   the   flap  
reminds you of the type of fuel to be
used.
Y

ou   must   fill   with   at   least   5   litres   of   fuel  
for

  it   to   be   registered   by   the   fuel   gauge.
When
  the   fuel   filler   cap   is   opened,  
there

  may   be   a   slight   inrush   of   air.  
This
 
vacuum is entirely normal and is due to
the

  sealing   of   the   fuel   system.
When
  filling   the   fuel   tank,   do   not  
continue after the 3rd cut-off of the
nozzle.
 This
 
could
 
cause   malfunctions.
The
 
capacity
 
of
 
the
 
fuel   tank   is  
approximately 60 litres (or 55 litres
according

 
to
 
version).
-
 
After

 
filling
 
the
 
fuel   tank,   lock   the  
cap

 
and
 
close
 
the   flap.
You then have approximately 8 litres
of
 
fuel
 
remaining.
Fill up without delay to avoid running
out
 
of
 
fuel.
Never
 
risk
 
driving
 
until
 
you
 
run
 
out
 
of
 
fuel as this may damage the emissions
control

 
and
 
injection
 
systems.
CHECKS
7
Fuel

163
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
DIESEL PRIMING
PUMP
If you run out of fuel, it is necessary to
prime
  the   fuel   circuit.
Other HDi engines
- Fill  the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Squeeze and release the manual
priming pump, under the bonnet,
under

  the   protective   cover.
-

Operate the starter until the engine
starts.
BlueHDi engine
- Fill   the   fuel   tank   with   at   least   five  litres
  of   Diesel.
-

Switch on the ignition (without
starting

  the   engine).
-

W
ait around 6 seconds and switch
off
  the   ignition.
-
 
Repeat
  the   operation   10   times.
-

Operate the starter to run the
engine.
FUEL CUT- OFF
In a serious collision, a mechanism
automatically prevents fuel from
reaching
  the   engine.
The
  flashing   of   this   warning  
lamp is accompanied by a
message

  in   the   screen.
Check
  that   there   is   no   odour   or  
leakage

  of   fuel   outside   the   vehicle   and  
re-establish

  the   fuel   supply:
-

switch of
f the ignition
(STOP


position),
-
 
remove
  the   key,
-
 
put
  the   key   back   in   the   ignition,
-
 
switch
  on   the   ignition   and   start.
CHECKS
7
AdBlue®

171
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
ECONOMY MODE
After the engine has stopped, with
the
  key   in   the   ignition   position,   certain  
functions (windscreen wiper

, electric
windows, courtesy lamps, audio
equipment,
  etc.)   can   only   be   used   for   a  
cumulative duration of thirty minutes, to
prevent

  discharging   of   the   battery.
Once the thirty minutes have elapsed,
the active functions are put on standby
and
  the   battery   warning   lamp   flashes  
accompanied by a message in the
screen.
T

o resume the use of these functions
immediately, start the engine and let it
run
  for   a   few   minutes.
The time available will then be double
the time for which the engine was left
running.
  However,   this   time   will   always  
be

  between   five   and   thirty   minutes.
A
 

flat   battery   will   prevent   the  
engine

  from   starting.
Battery
QUICK HELP
8

229
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
Select a radio station or frequency (refer to the
corresponding section). Press on Radio Media
to display the
primary pag e.
Press
  on   the   secondary   page.
Select " Settings ".
Select " Radio".
Activate/deactivate
 " R

DS
options ".
Press on Radio Media
to display the
primary
 pag

e.
Press
 
on
 
the
 
secondary
 
page. Press on "
Save"
  (preset).
Select a number in the list to preset the
previously
  chosen   radio   station.
A long press on a number saves (presets) the
station.
Press on Frequency
.
Enter the frequency in full
(e.g.: 92.10 MHz)
 
using
 
the
 
keypad
 
t

hen " Confirm ".
Changing radio station
Pressing the name of the current radio station
brings
 
up
 
a
 
list.
To change radio station press the name of the
desired
 s

tation. Or
Press on Radio Media to display the
primary
 pag

e.
Select " Save"
  (preset).
Presetting a station Activating / Deactivating RDS
OR
THEN
A press on this button presets all of
the
  stations   one   after   the   other.
Recalling preset stations
RDS, if activated, allows you to continue
listening to the same station by automatic
retuning  to   alternative   frequencies.
 H

owever, in certain conditions, coverage
of an RDS station may not be assured
throughout the entire country as radio
stations do not cover 100 % of the
territory.
  This   explains   the   loss   of
 r

eception   of   the   station   during   a   journey.
Audio and Telematics
TECHNOLOGY on BOARD
10

 273
Berlingo2VP_en_Chap10b_RD45_ed02-2016
Use only USB memory sticks formatted FAT32 (File   Allocation   Table).
It is recommended that you use
genuine Apple
® USB cables for correct
operation.
*

I
n certain cases, play of the audio files must
be
  initiated   from   the   keypad.
**
  If   the   telephone   supports   the   function.
Bluetooth® audio streaming
Streaming allows music files on the telephone
to  be   played   via   the   audio   system.
Connect
  the   telephone:   see   the   "Telephone "
section.
Select in the " Bluetooth: Telephone - Audio "
menu
  the   telephone   to   be   connected.
The audio system connects to a newly paired
telephone
 a

utomatically.
Control
  of   tracks   to   be   played   is   via   the   buttons  
o

n the audio system control panel and the
steering
  mounted   controls**.   The   contextual  
i

nformation   can   be   displayed   in   the   screen.
Activate the streaming source by
pressing the SOURCE
*
  button.
Connecting Apple® players
Connect the Apple® player to the USB port
using
 
a
 
suitable
 
cable   (not   supplied).
Play
 
starts
 
automatically.
Control
 
is
 
via
 
the
 
audio   system.
The classifications available are those of the
portable
 
device
 
connected   (artists   /   albums   /  
g

enres
 
/
 
playlists
 
/
 
audiobooks   /   podcasts).
The version of software in the audio system
may not be compatible with the generation of
your Apple
® player.
T
o protect the system, do not use a
USB
 
hub.
Audio and Telematics
TECHNOLOGY on BOARD
10

274
Berlingo2VP_en_Chap10b_RD45_ed02-2016
Telephone
Pairing a Bluetooth® telephone
Screen C
(Available according to model and version)
As a safety measure and because they
require prolonged attention on the part
of the driver, the operations for pairing
of the Bluetooth
® mobile telephone with
the Bluetooth® hands-free system of
your audio equipment must be carried
out with the vehicle stationary and the
ignition
 o

n.
Go
 
to
 
www.citroen.co.uk   for   more   information  
(

compatibility,
 
more
 
help, ...).
Activate the telephone's Bluetooth
® function
and ensure that it is "visible to all" (telephone
configuration).
Press the MENU
 

button. In
  the   menu,   select:
- "
Bluetooth : Telephone - Audio "
- "
Bluetooth configuration "
- "
Perform a Bluetooth search "
A window is displayed with a message that a
search   is   in   progress.
The services available depend on
the   network,   the   SIM   card   and   the  
c

ompatibility of the Bluetooth
® device
used.
Consult your telephone's manual and
your operator to find out which services
are
 
available
 
to
 
you.
*
 
If
 
your
 
telephone
 
is
 
fully
 
compatible. The first 4 telephones recognised are displayed
in
 
this
 
window.
The " Telephone " menu permits access to the
following
 
functions
 
in
 
particular:
 
" Directory " *,
" Calls list ", "Consult the paired equipment ".Select the telephone to be connected from the
list.
  Only   one   telephone   can   be   connected   at  
a

  time.
A   virtual   keypad   is   displayed   in   the   screen:  
e

nter   a   code   with   at   least   4   digits.
Confirm by pressing OK.
A message in the screen indicates the telephone
chosen.   To   accept   the   pairing,   enter   the   same
 c

ode on the telephone, then confirm with OK.
If pairing fails, the number of attempts is not
limited.
A message that the pairing has been
successful
  appears   in   the   screen.
The automatic connection authorised is only
active
  after   the   telephone   has   been   configured.
The directory and the call list can be accessed
after
  the   necessary   synchronisation   period.
Audio and Telematics

 275
Berlingo2VP_en_Chap10b_RD45_ed02-2016
Receiving a call
An incoming call is announced by a ring and a
superimposed  display   in   the   screen.
Select the YES tab on the display
using
  the   buttons.
Confirm by pressing OK.
Press this button at the steering
mounted
  controls   to   accept   the   call.
Making a call
From the "Bluetooth : Telephone - Audio "
menu.
Select " Manage the telephone call".
Select " Call".
Or
Select " Calls list ".
Or
Select " Directory ".
Press this button for more than two
seconds for access to your directory,
then
  navigate   using   the   thumbwheel.
Or
To
  dial   a   number,   use   your   telephone's   keypad,  
w

ith   the   vehicle   stationary.
Ending a call
During a call, press this button for
more  than   2   seconds.
Confirm with OK
 

to   end   the   call.
The system accesses the telephone's
contacts directory, depending on its
compatibility, and while it is connected
by Bluetooth
®.
With certain telephones connected by
Bluetooth
® you can send a contact to
the
 
directory   of   the   audio   system.
Contacts imported in this way are
saved in a permanent directory
visible to all, whatever the telephone
connected.
The menu for the directory is not
accessible
  if   it   is   empty.
Audio and Telematics
TECHNOLOGY on BOARD
10