light Citroen BERLINGO MULTISPACE RHD 2017 2.G Owner's Guide

164
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
BLUEHDI AND ADBLUE®
SCR technology
AdBlue® is the brand name of the
solution needed for operation of the
SCR
 
system.
The aim of BlueHDi is to reduce the
emissions of NOx (nitrous oxides) in
the air by up to 90%, using a system
that converts NOx into water vapour
and nitrogen in a dedicated catalytic
converter:
  SCR   (Selective   Catalytic  
Reduction).
This

 
objective   meets   the   "Euro   6"  
emissions standard adopted by the
European Union aimed at limiting the
emissions of pollutants from internal
combustion

  engines.
The SCR technology used on BlueHDi
engines
  involves   the   injection   of  
AdBlue® into the exhaust system.
BlueHDi   vehicles   have   a   specific  
AdBlue® additive tank with a capacity
of 17 litres .
It
 
has
 
an   exterior   filler   with   a   blue filler
cap, located to the left of the Diesel
fuel
 
filler   cap.
Filling of the AdBlue
® tank can be done using 5 or 10 litre containers,
1.89
 
litre
 
bottles,
 
or
 
when   at   a   fuel  
fillin

g
 
station
 
equipped   with   a   special  
AdBlue® delivery pump for light
vehicles.
This operation can also be carried
out by a CITROËN dealer or a
qualified
  workshop.
Please note that the high delivery
pumps
 
at   some   filling   stations,  
intended only for lorries and coaches,
are not suitable for cars or light
commercial

  vehicles.
Never
 
use   these   pumps.
AdBlue®

165
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Good practice
While the quantity of AdBlue® in
the
 
additive
 
tank
 
is
 
sufficient,
 
no
 
information

 
is
 
displayed.
On
 
the
 
other
 
hand,
 
once
 
the
 
fluid
 
level drops to the quantity needed
for

 
a
 
range
 
of
 
1
 
500
 
miles
 
(2
 
400
 
km)  
driving, you are warned by dif

ferent
temporary signals (warning lamp,
message,
 
audible
 
signal).
As more miles are covered, these
signals intensify and the message
becomes
 
permanent.
When the AdBlue
® tank is empty, restarting
 
becomes   impossible.
It is strongly recommended that you
do not wait for the successive alerts
before topping-up the AdBlue
® additive,
but
 
do
 
this
 
as
 
soon
 
as
 
possible.
Filling the AdBlue® tank
For light vehicles, 5 or 10 litre
containers
 
and
 
1.89
  litre  
(1/2 US gallon)

 
bottles   are   available  
from CITROËN dealers, until they are
equipped

with AdBlue
® delivery pumps.
If
 
you
 
want
 
to
 
fill
 
the
 
AdBlue® tank yourself, ensure that you have a
suitable
 
filler
 
pipe,
 
which
 
may   or   may  
not be supplied with the additive
container

.
CHECKS
7
AdBlue®

169
Berlingo2VP_en_Chap07_Verification_ed02-2016Berlingo2VP_en_Chap07_Verification_ed02-2016
Filling
Ensure that the vehicle is parked on a flat  and   level   surface.
Pour
  the   contents   of   the   container   /  
bottle

  into   the   dedicated   tank.
After
  filling   the  
AdBlue® tank, observe the
 
following
 
procedure:
-

Switch on the ignition without
starting.
-


W

ait 10 seconds before starting the
engine.
Never dispose of empty AdBlue
®
containers and bottles in the
household
 
waste.
Place them in a special container
provided
 
this
 
purpose
 
or
 
take
 
them
 
to  
your

 
dealer. Keep AdBlue
® out of the
reach of children, in its original
container.
Never transfer AdBlue
® to another
container:
 
it
 
would
 
loose   its   purity.
Never
 
dilute
 
the
 
fluid
 
with   water.
Never
 
pour
 
the
 
fluid
 
into   the   Diesel   fuel  
tank.
Recommendations on storage
Never store containers or bottles of
AdBlue® in your vehicle.
Freezing of the AdBlue
®
AdBlue® freezes at about -11°C (12.2° F) and
 
deteriorates   above   25°C   (77°F).
It is recommended that containers and
bottles be stored in a cool area and
protected
  from   direct   sunlight.
Under
 
these   conditions,   the   fluid   can  
be

 
kept
  for   at   least   a   year.
Additive that has been frozen can
be used once it has thawed out in
ambient air. The SCR system includes an
AdBlue
® tank heater that ensures operation of the vehicle in normal
conditions.
In exceptional situations, such as when
the
 
vehicle
 
is   kept   at   temperatures  
below -15°C (5°F) for a long period,
there may be an emission fault alert
related to freezing of the

AdBlue
®
additive.
Park
 
the
 
vehicle
 
in
 
an
 
area
 
at
 
a
 
more  
moderate temperature for a few hours
until

the AdBlue
® becomes a fluid again.
The emissions warning lamp does not
go of
f immediately, but does so after a
few
 
miles
 
of
 
driving.
CHECKS
7
AdBlue®

173
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
1. Parking the vehicle
- The occupants must get out of the
vehicle  and   wait   in   a   safe   location.
-
 
If
  possible,   park   the   vehicle   on  
level, stable and non-slippery
ground.
-

 
Apply
  the   parking   brake,   switch  
of

f   the   ignition   and   engage   first   or  
reverse

  gear. -
 
Place
  a   chock   under   the   wheel  
diagonally opposite the one to be
changed.CHANGING A WHEEL
under the passenger footwell behind
the
  driver's   seat.
-

If necessary
, move the seat forward
to access the storage compartment
from
  the   rear.
-
 
Remove
  the   flap   then   take   out   the  
jack

  and   the   tool   carrier.
-

Remove the tools needed from the
carrier

.
1.
 
Jack.
2.

 
Wheelbrace.
3.

 
Chock.
4.


Spanner for the Modutop roof bars
and

  rear   lamps.
5.
 
Alloy
  wheel   trim   removal   tool.
6.
 
T
owing   eye.
If
 
the
 
vehicle
 
is
 
fitted
 
with
 
a
 
towbar,
 it is sometimes necessary to raise
the
 
vehicle
 
slightly
 
to
 
make
 
it
 
easier
 
to remove the spare wheel from its
carrier

.
2. Tools
The tools are stowed in a storage area
closed   by   a   flap   under   a   front   seat.
However, if the vehicle is not equipped
with a spare wheel, the towing eye is
located in the storage compartment On   certain   types   of   ground   and/
or if considerable loads are being
transported, call a CITROËN dealer or
a   qualified   workshop.
The   jack   and   tools   are   specific   to   your  
vehicle.

  Do   not   use   them   for   other  
purposes.
QUICK HELP
8
Changing a wheel

181
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
CHANGING A BULB
Type A
All  glass   bulb:   pull   gently  
as

  it   is   fitted   by   pressure.
Type C
Halogen
  bulb:   release   the  
retaining spring from its
housing. T
ype B
Bayonet
  bulb:   press  
on the bulb then turn it
anticlockwise.
T

ypes of bulb
Various
 
types
  of   bulb   are   fitted   to   your  
vehicle.
T

o
 
remove
 
them:
Type D
Light-emitting diode
(LED):
  for   replacement  
of the daytime running
lamps, contact a
CITROËN dealer or a
qualified

  workshop.
QUICK HELP
8
Changing a bulb

183
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
3. Direction indicators
Type B, PY21W - 21W (amber)
-
Remove the cover by pullin
g the
flexible
  rubber   tab.
-

T
urn the bulb holder a quarter turn
anticlockwise.
-

Remove the bulb by pressing it
lightly

  while   turning   it   anticlockwise.
-
 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure correct
sealing. 4. Front foglamps
T

ype C, H1 - 55W
-

Remove the three clips and the
screw securing the wheel arch liner

,
located
  below   the   bumper.
-
 
Move
  the   wheel   arch   liner   upwards.
-

Disconnect the bulb holder
connector by pressing the tab at
the

  top.-

Remove the bulb holder by
squeezing the two clips (at top and
bottom)

  using   a   finger   and   thumb.
-

Replace the module (bulb holder
and

  bulb).
-

Carry out the operations in reverse
order

  to   fit   the   module   and   refit   the  
wheel

  arch   liner.
QUICK HELP
8
Changing a bulb

185
Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016Berlingo2VP_en_Chap08_Aide-rapide_ed02-2016
Rear lamps
This procedure requires the use of
the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the wiring
correctly to avoid trapping the
wiring.
After changing the rear direction
indicator bulb, the reinitialisation time is
above

  2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-

Remove the faulty bulb by
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-

with tailgate, pull the lamp unit
towards the centre of the vehicle,
-


with hinged doors, pull the lamp
unit

  towards   you.
For more information on bulbs, refer to
the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


T

ype B,
 
P21/5W
 
-
 
21/5W
2.

Direction indicators


T

ype B, PY21W - 21W (amber)
3.

Reversing lamps


T

ype B, P21W - 21W
4.

Foglamps


T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the other lamps
and their edges to avoid damaging
their
 
coating
 
and
 
seals. Chapter 9, "Changing a wheel"
section.
-

Identify the failed bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-

Holding the lamp, disconnect the
electrical

  connector.
QUICK HELP
8
Changing a bulb

 197
Berlingo2VP_en_Chap09_Caract-technique_ed02-2016Berlingo2VP_en_Chap09_Caract-technique_ed02-2016
ENGINE CHARACTERISTICS
The engine characteristics (capacity,
maximum power, maximum power
speed, fuel, CO
2 emissions...) for your vehicle are given in the registration
certificate.
These characteristics correspond
to the values type-approved
on a test bed, under conditions
defined
 
in
 
European   legislation  
(Directive 1999/99/EC).
For more information, refer to the
manufacturer's website or sales
brochure

 
for
 
the
  model.   Contact  
a

 
CITROËN
 
dealer   or   a   qualified  
workshop.
WEIGHTS AND TOWED LOADS
These values, expressed in kg, can be found on the manufacturer's VIN plate
or
  label.
The maximum weights and towed
loads for your vehicle can be found on
the
  vehicle's   registration   certificate.
The
  kerb   weight   is   equal   to   the   weight  
without

  load   +   driver   (75   kg)   +   fuel   tank  
filled

  to   90%.
The GTW and towed load values
indicated are valid up to a maximum
altitude
  of   1000   metres.  
The
  value   of  
the towed load mentioned must be
reduced by 10 % for each additional
1000

  metres.
With
  load   transfer,   the   braked   trailer  
weight can be increased, on condition
that the equivalent of this load is
removed from the vehicle so that the
GTW

  is   not   exceeded. High ambient temperatures
may result in a reduction in the
performance of the vehicle in
order
  to   protect   the   engine.   When   the  
ambient temperature is higher than
37 °C,

  limit   the   towed   weight.
Towing with a lightly loaded
vehicle can adversely affect road
holding.
Towing
  a   trailer   increases   braking  
distances.
When towing, the maximum permitted
speed is reduced (comply with the
legislation

  in   force   in   the   country).
The recommended nose weight is
the downward force on the towball
(removable
  with   or   without   tools).
GVW: gross vehicle weight, the
maximum
  authorised   weight.
GTW: gross train weight, the maximum
weight
  for   vehicle   plus   trailer.
The location of the manufacturer's
plate is given in chapter 9,
"Identification
  markings"   section.
In each country, it is imperative that
the maximum towed loads authorised
by local legislation are complied
with.
 
T
o   find   out   your   vehicle's   towing  
capacities and its gross train weight,
consult

  a   CITROËN   dealer.
TECHNICAL DATA
9
Weights

243
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
As a safety measure and because it
requires sustained attention by the
driver, using a smartphone when
driving  is   prohibited.
All operations must be done with the
vehicle stationary .
The synchronisation of a
smartphone allows applications on a
smartphone that are adapted to the
MirrorLink
TM technology to be displayed
i
n
 
the
 
vehicle's   screen.
The principles and standards
are
 
constantly   evolving.   For   the  
c

ommunication process between the
smartphone
  and   the   system   to   work  
c

orrectly, the smartphone must be
unlocked;
 
update   the   operating   system  
o

f your smartphone as well as the date
and time in the smartphone and the
system.
For the list of eligible smartphones,
connect to the brand's internet website
in
 
your
 
country. As a safety measure, applications
can only be viewed with the vehicle
stationary; display is interrupted once
the
  vehicle   is   moving.When connecting a smartphone to the
system, it is recommended that Bluetooth®
be
 
started
 
on
 
the
 
smartphone.
Start the application on the
smartphone (optional, depending
on the smartphone and operating
syste m).
Access to the different audio sources remains
accessible
  in   the   margin   of   the   MirrorLink
TM
display,
 
using
 
touch
 
buttons
 
in
 
the
 
upper
 
bar.
Access to the menus for the system is possible
at
 
any
 
time
 
using
 
the
 
dedicated
 
buttons.
During the procedure, several screen
pages relating to certain functions
are
 
displayed.
Accept to start and end the
connection.
Connect
 
a
 
USB
 
cable.
 
The
 
sm

artphone charges when
connected
 
by
 
a
 
USB
 
cable.
Press on " MirrorLink
TM" to
start the application in the
system. Once connection is established, an page
is displayed with the applications already
downloaded to your smartphone and adapted
to
  MirrorLink
TM technology.
If only one application has been downloaded to
the
 
smartphone,   it   starts   automatically.
MirrorLinkTM smartphone
connection
Press the end of the lighting control stalk to s
tart voice recognition of your smartphone via
the
  system.
Voice recognition requires a compatible
smartphone connected to the vehicle by
Bluetooth
®.
Voice recognition
Please note:
- i f your smartphone is supported, to
make
  it   "MirrorLink
TM" compatible,
some phone manufacturers
nevertheless invite you to first
download
 
a
 
dedicated   application.
From the system, press on
" Connected services " to display the
primary
 pag

e.
Audio and Telematics
TECHNOLOGY on BOARD
10

 247
Berlingo2VP_en_Chap10a_SMEGplus_ed02-2016
As a safety measure and because it
requires sustained attention by the
driver, using a smartphone when
driving  is   prohibited.
All operations must be done with the
vehicle stationary .
As a safety measure, applications
can only be viewed with the vehicle
stationary; display is interrupted once
the
  vehicle   is   moving.
The synchronisation of a
smartphone allows applications on a
smartphone that are adapted to the
CarPlay
® technology to be displayed on
t
he
 
vehicle's   screen.
As the principles and standards are
constantly evolving, it is recommended
that you update the operating system of
your
 
smartphone.
For the list of eligible smartphones,
connect to the brand's internet website
in
 
your
 
country. On connecting the USB cable, the
"
Telephone " function changes to
" CarPlay "   in   the   menu   carousel.
Press on " CarPlay" to display the
CarPlay
® inter face.
P
ress on " CarPlay" to display the
CarPlay
® inter face.
C
onnect
  a   USB   cable.   The  
sm

artphone charges when
connected   by   a   USB   cable.
Press   the   end   of   the   lighting   control   stalk   to  
s

tart voice recognition of your smartphone via
the   system.
CarPlay® smartphone
connection
During the procedure, one or more
screen pages relating to certain
functions
  are   displayed   on   connection.
From the system, press on
"
Connected services " to display the
primary
 pag
e.
Connect   the   USB   cable.   The  
s

martphone is charged while
connected   by   the   USB   cable.
Or
Voice recognition
When the telephone menu is displayed,
connection of the USB cable causes the
display to automatically change to CarPlay
mode.
When another menu is displayed, on
connection of a USB cable a message is
displayed in the upper bar, indicating that
CarPlay mode
  has   been   activated.
Press
  Open   to   display   CarPlay   mode.
Audio and Telematics
TECHNOLOGY on BOARD
10