change key battery Citroen BERLINGO MULTISPACE RHD 2017 2.G Owner's Manual

19
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
Good practice
Take care not to allow the remote control to come into contact with
grease, dust, rain or a damp
environment.
A
 
heavy   object   attached   to   the   key  
(key

  ring,   ...)   weighing   on   the   shaft  
of

  the   key   in   the   switch,   may   cause   a  
malfunction.
REMOTE CONTROL
Reinitialising the remote

control
Following changing of the remote
control battery or disconnection of the
vehicle battery, the remote control may
have
  to   be   reinitialised.
Wait at least one minute before using
the
  remote   control.
Insert
  the   key   in   the   ignition   switch   with  
the

  buttons   (padlocks)   of   the   remote  
control

  facing   you.
Switch
  on   the   ignition.
Press
  the   locking   padlock   for   at  
least

  five   seconds   within   the   next  
ten seconds.
Switch

  off   the   ignition.
Wait at least one minute before using
the
  remote   control.
The
  remote   control   is   now   working  
again.
Use only identical batteries or
batteries of an equivalent type to
those recommended by CITROËN
dealers.
Do not discard the remote control
batteries, they contain metals which
are

 
harmful
 
to
 
the
 
environment.
Deposit them at a CITROËN
dealership, or at an authorised
collection
 
point.
Unfolding / folding
Changing the battery
Battery ref.: CR1620 / 3 volts.
The   "battery   flat"   information   is   given  
by an audible signal, accompanied by
a

  message   in   the   screen.
To replace the battery, unclip the
casing
  using   a   coin   at   the   ring.
If
  the   remote   control   does   not   work  
after the battery has been changed,
reinitialise

  the   remote   control.
There
  is   a   risk   of   damage   if   the  
replacement battery is not the correct
type.If you do not press the button,
you

  may   damage   the   key's  
folding

  mechanism.
Access
READY TO GO
3

55
Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016Berlingo2VP_en_Chap03_Pret-a-partir_ed02-2016
The Stop & Start system
requires  a   battery   of   specific  
characteristics.

 
All
  work   on   this  
type of battery must be done only
by

 
a
  CITROËN   dealer   or   a   qualified  
workshop.
For more information on the 12 V
battery

,   refer   to   "Battery"   in   section   8.
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If the temperature is high
enough, the warning lamp
comes on for less than
one second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp to go off then operate the starter
(Starting position) until the engine
starts. Door or bonnet open
warning lamp
If this comes on, a door or the bonnet
is
  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return
  to   idle.
Do not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system
 
to
 
avoid
 
the
 
risk
 
of
 
injury
 
related to an automatic change to
ST

ART
 

mode.
Driving on flooded roads
Before
 
driving
 
through
 
a
 
flooded
 
road,
 
it is strongly recommended that you
deactivate

 
the
 
Stop
 
&
 
Start
 
system.
For more advice on driving, particularly
on
 
flooded
 
roads,
 
refer
 
to
 
the
 
corresponding

 
section.
READY TO GO
3
Stop & Start