light Citroen C CROSSER 2008 1.G User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C CROSSER, Model: Citroen C CROSSER 2008 1.GPages: 216, PDF Size: 4.85 MB
Page 23 of 216
I N S T R U M E N T S a n d C O N T R O L S
I
26
Message is on
Associated
warning light
Cause Solution - action Observations
Dynamic
stability control
system (ASC) F i x e d
- Dynamic stability
control system
(ASC) fault. Consult a CITROËN
dealer.
Four wheel
drive system F i x e d
- Four wheel drive
transmission
system fault. Consult a CITROËN
dealer.
Four wheel
drive system temperature F i x e d
- The temperature
of the four wheel
drive transmission
system is too
high. Stop the vehicle and
contact a CITROËN
dealer.
The vehicle switches
to front wheel
drive (2 WD) mode
automatically.
Automatic
headlamp
adjustment system F i x e d
- The automatic
headlamp
adjustment is
faulty. Consult a CITROËN
dealer.
O n l y o n v e h i c l e fi t t e d
w i t h x e n o n b u l b s .
Battery
charge F i x e d
Battery charge
fault. Stop the vehicle and
contact a CITROËN
dealer.
E x t e r i o r
temperature F i x e d
- T h e e x t e r i o r
temperature 3 °C
(37 °F) or below. Road icy.
Pay attention and
drive slowly. Caution: The road may
be icy even when this
screen is not displayed.
Page 24 of 216
I N S T R U M E N T S a n d C O N T R O L S
I
27
Message is on Associated
warning light Cause Solution - action Observations
Saturation of
the particle
e m i s s i o n fi l t e r F i x e d
- Start of saturation
of the particle
e m i s s i o n fi l t e r . A s s o o n a s t r a f fi c
conditions permit,
r e g e n e r a t e t h e fi l t e r
by driving at a speed
of at least 35 mph
(60 km/h) until the
message is cleared. If the message is still
displayed, contact a
CITROËN dealer.
Diesel
additive level F i x e d
- Low diesel
additive level. Have the level topped
up by a CITROËN
dealer without delay.
Water in the
d i e s e l fi l t e r
(according to country) F i x e d
- The presence
of water in the
d i e s e l fi l t e r i s
indicated.
Risk of damage
to the injection
system on Diesel
engines. Contact a CITROËN
dealer without delay.
Page 33 of 216
I N S T R U M E N T S a n d C O N T R O L S
I
36
Restoring the manufacturer’s
parameters (REINITIALISE)
You can restore all of the manufacturer’s
settings for all of the functions.
On the menus screen:
press the INFO button to select
“REINITIALISE”
(located on menu
2/2) .
press and hold the
INFO button for
at least 5 seconds .
An audible signal is heard and all of the
manufacturer’s settings are restored for
all of the functions. The manufacturer’s settings are: LIGHTING RHEOSTAT
With the lights on or off, press the button
to change the intensity of the lighting of
the instruments and controls in “day” or
“night” mode.
W h e n t h e l i g h t i n g r e a c h e s t h e m a x i m u m
setting, press again to change to the
minimum setting.
When the lighting reaches the required
intensity, release the button.
The setting is saved when the ignition
switch is turned to OFF. An audible signal is heard and the
intensity of the lighting increases
each time the button is pressed.
System for manual adjustment of the
brightness of the instruments and
c o n t r o l s i n r e l a t i o n t o t h e e x t e r i o r
brightness.
Functions
Manufacturer’s
setting
Reinitialisation
of the average
consumption and
average speed
1 (automatic)
Fuel consumption
units
L/100 km
Temperature
display unit
°C
Display language ENGLISH
INFO button
sound
ON (activated)
Displaying of the
“BREAK ADVISED”
message
OFF (deactivated)
Page 43 of 216
C O M F O R T
II
46
Air conditioning On / Off (5)
Press button 5 to activate the air
conditioning.
The indicator light comes on.
Intake of exterior air / Recirculation of interior air (4)
This function insulates the passenger
c o m p a r t m e n t f r o m e x t e r i o r o d o u r s a n d
smoke.
Press button 4 to select the air in-
take mode.
When the indicator light on button 4 is
o f f , t h e e x t e r i o r a i r i n t a k e f u n c t i o n i s a c -
tivated.
When the indicator light on button 4 is
o n , t h e i n t a k e o f e x t e r i o r a i r i s d e a c t i -
vated and the system is in air recircula-
tion mode.
Do not drive for long periods in in-
t e r i o r a i r r e c i r c u l a t i o n m o d e , e x c e p t
i n t r u l y e x c e p t i o n a l a t m o s p h e r i c
conditions. Personalisation of the Exterior air
intake / Interior air recirculation
function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to change
the air intake mode at any time.
Personalisation of the Air
Conditioning On / Off function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to activate
or deactivate the air conditioning at any
time.
The settings are retained, even after
switching off the ignition.
Changing the status
Press the Air Conditioning On / Off but-
ton for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
i n d i c a t o r l i g h t fl a s h e s t h r e e t i m e s .
When the status changes from inactive
to active, two bleeps are heard and the
i n d i c a t o r l i g h t fl a s h e s t h r e e t i m e s .
Automatic control active
If the air distribution adjustment dial and
t h e a i r fl o w a d j u s t m e n t d i a l a r e p l a c e d
in the “AUTO” position, or if the temper-
ature control dial is set to the minimum
temperature, the air conditioning sys-
tem is controlled automatically.
Automatic control active
If the air distribution adjustment dial
a n d t h e a i r fl o w a d j u s t m e n t d i a l a r e
placed in the “AUTO” position, the Air
intake / Interior air recirculation func-
tion is also controlled automatically.
Changing the status
Press the Air intake / Interior air recircu-
lation button for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
i n d i c a t o r l i g h t fl a s h e s t h r e e t i m e s .
When the status changes from inactive
to active, two bleeps are heard and the
i n d i c a t o r l i g h t fl a s h e s t h r e e t i m e s .
Automatic control inactive
Even if the air distribution adjustment
d i a l a n d t h e a i r fl o w a d j u s t m e n t d i a l a r e
placed in the “AUTO” position, the Air
intake / Interior air recirculation function
is no longer controlled automatically.
Automatic control inactive
The air conditioning system is no
longer controlled automatically.
Page 44 of 216
C O M F O R T
II
47
Windows and windscreen de-icing
De-icing
1. Press button A t o s e l e c t “ e x t e r i o r a i r
intake”. The indicator light on this
button is switched off.
2. Place the air distribution dial in the
“windscreen, side windows and foot-
wells” position.
3. S e l e c t t h e a i r fl o w r e q u i r e d .
4. Select the temperature required.
5. Press the “air conditioning on / off”
button
B to activate the air condi-
tioning. The indicator light on this
button comes on. Rapid de-icing
1. Place the air distribution dial in the
“windscreen and side windows”
position.
2. S e l e c t t h e m a x i m u m a i r fl o w .
3. S e l e c t t h e m a x i m u m t e m p e r a t u r e .
Rear screen de-icing (6)
With the engine running, press but-
ton 6 to activate the de-icing of the rear
s c r e e n a n d e x t e r i o r m i r r o r s .
The indicator light on the button comes
on while the de-icing is in operation.
The de-icing switches off automatically
t o p r e v e n t a n e x c e s s i v e c o n s u m p t i o n o f
current.
The operation of the de-icing can be
stopped before it is switched off auto-
matically by pressing the button again.
It is advisable to switch off the rear
screen de-icing as soon as pos-
sible as lower current consumption
reduces the fuel consumption.
Page 45 of 216
C O M F O R T
II
48
FRONT SEATS
Manual mode
Forwards-backwards adjustment
Raise the control bar and slide the seat
forwards or backwards.
When your seat is at the correct dis-
tance, move it forwards and backwards
slightly without using the control bar to
check that it is secured correctly. Driver’s seat cushion height and
angle adjustment
Pull and/or push the control several
times to adjust the height of the seat.
Seat back angle adjustment
Pull the control upwards to adjust the
seat back.
When the seat back is at the correct
angle, release the control.
To prevent the seat back from
moving forward sharply and
knocking you, press on it with
your back or push it with your
hand while operating the lever.
Seat consisting of a seat cushion, seat
back and head restraint which can all
be adjusted to your optimum driving
and comfort position.
Page 47 of 216
C O M F O R T
II
50
Head restraint height adjustment Front armrest
Heated seats adjustment
The adjustment is correct when the
top of the head restraint is aligned
with the top of the head of the seated
person. Never drive with the removed
head restraints in the vehicle
as they could be thrown
around the vehicle on sharp braking.
They must be in place and adjusted
correctly.
After installing the head restraint,
check that the height adjustment
button is locked correctly.
You can move the console housing
cover in order to use it as an armrest.
With the
engine running , tilt the button
to the position required.
The temperature of the seat is regulat-
ed automatically.
There are two setting positions:
- “HI”: High heating
- “LO”: Low heating
When the button is in the intermediate
position, the heating is switched off.
The indicator lights A comes on when
the system is activated . To raise the head restraint, pull it
upwards.
To lower the head restraint, push it
downwards pressing the height adjust-
ment button at the same time.
To remove the head restraint, bring it to
the uppermost position then remove it
pressing the height adjustment button
at the same time.
T o r e fi t t h e h e a d r e s t r a i n t , e n g a g e t h e
stems of the head restraint in the holes
pressing the height adjustment button
at the same time.
Page 48 of 216
C O M F O R T
II
51
REAR SEATS (ROW 2)
Seat back angle adjustment
Pull the control and adjust.
When the seat back is at the correct
angle, release the control.
Sit in the centre of the rear bench seat
to check that the two seats are at the
same level and that the angle of their
seat backs is the same.
Forwards-backwards adjustment
Pull the control towards the outside and
adjust.
When your seat is at the correct
distance, release the control.
To ensure that the seat is secured
correctly, move it forwards and
backwards slightly without using the
control. When manoeuvring the seats,
ensure that no person or ob-
ject is in the vicinity of the mov-
ing parts to avoid any risk of injury or
damage.
To prevent the seat back from mov-
ing forwards sharply and knocking
you, press on it with your back or
push it with your hand while operat-
ing the lever.
The rear seats can be folded in two
parts (1/3 - 2/3).
Page 50 of 216
C O M F O R T
II
53
Folding the second row
1. Raise the rear seat lever A , or
Pull the button in the boot B for at least one second, or
Pull the rear seat releasing strap C towards you.
2. The seat backs fold forwards then the cushion rises and folds fo rwards.
3. After carrying out these operations, press on the seat lightly to check that it is secured correctly.
Before folding the seats, lower the head restraints fully.
Before folding the seat backs forwards, insert the seat belt b
uckles in the slots provided for this purpose in the rear seat
cushion.
Before folding the seats , ensure that no object or person is hindering the execution of the operatio ns.
Do not place luggage on the folded seats.
Page 51 of 216
C O M F O R T
II
54
Returning the second row to the normal position
1. Lower the seat pulling simultane-
ously on the releasing strap
A lo-
cated at the rear of the cushion and
supporting the seat with your hand.
Force may be necessary to carry out these operations.
O n v e h i c l e s fi t t e d w i t h a t h i r d r o w , t h e r e a r o f t h e c u s h i o n o f t h e s e c o n d r o w i s fi t t e d w i t h a l o w l i g h t B .
W h e n t h e r e l e a s i n g s t r a p i s p u l l e d , t h e l i g h t c o m e s o n f o r a p p r o x i m a t e l y 1 0 s e c o n d s t o l i g h t t h e fl o o r a t t h e b a s e o f t h e
third row.
2. Press on the cushion to put it in
place until it engages.
3. Pull the seat back upright pulling si-
multaneously on the releasing strap
located at the rear of the seat back.
4. After putting the seat back back in
place, push the seat and the seat
back lightly to ensure that they are
secured correctly.