service schedule Citroen C CROSSER 2008 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C CROSSER, Model: Citroen C CROSSER 2008 1.GPages: 216, PDF Size: 4.85 MB
Page 25 of 216
I N S T R U M E N T S a n d C O N T R O L S
I
28
Prevention messages
Information messages (ignition at “ON”)
Message is on Status of the system
2WD two wheel
drive system Flashing When the “2WD” (2 wheel drive) mode is selected using the
transmission mode selector.
4WD four wheel
drive system Flashing When the “4WD” (4 wheel drive) mode is selected using the
transmission mode selector.
This mode is the default mode.
4WD LOCK four
wheel drive system Flashing When the “LOCK” (4 wheel drive) mode is selected using the
transmission mode selector.
Dynamic stability
control system (ASC) F i x e d
When the dynamic stability control system (ASC) is active.
E x t e r i o r
temperature F i x e d T h i s i n d i c a t e s t h e e x t e r i o r t e m p e r a t u r e .
When the vehicle is stationary or if the speed is below 12 mp
h
(20 km/h) the temperature displayed may not correspond to the
e x t e r i o r t e m p e r a t u r e .
Display is on Cause Solution - action Observations
Service
indicator F i x e d Informs the driver of
the time remaining
before the vehicle’s
scheduled service. Consult a
CITROËN dealer.
This is displayed for a few
seconds when the ignition is
switched on.
Break
advised F i x e d Informs the driver that
he should stop to take
a break. You are advised to
take a break. This is displayed when the
driving time that you set
previously is reached.
An audible signal is heard
3 times and is then heard every
5 minutes until the vehicle stops.
Page 28 of 216
I N S T R U M E N T S a n d C O N T R O L S
I
31
SERVICE INDICATOR Resetting the service indicator
to zero
Your CITROËN dealer carries out this
operation after each service.
If you have carried out your vehicle’s
service yourself, the zero reset
procedure is the following:
switch off the ignition.
press the INFO button several times
in succession until the service indi-
cator is displayed.
press and hold the INFO button for
a few seconds until the spanner
fl a s h e s .
press the INFO button while the
s p a n n e r i s fl a s h i n g t o c h a n g e t h e
display “---” to “CLEAR” then the
t i m e r e m a i n i n g b e f o r e t h e n e x t s e r v -
ice is due is displayed.
Service overdue
Operation
When the ignition is switched on, you
must press the INFO button several
times in succession until the service
indicator is displayed. The distance
recorder display line indicates the
number of miles (kilometres) remaining
and the time elapsed line indicates the
number of months remaining before the
n e x t s e r v i c e i s d u e .
After a certain distance and a
certain time, the displaying of “---”
is reinitialised and the display
indicates the time remaining before
t h e n e x t s e r v i c e i s d u e .
System which informs the driver when
t h e n e x t s e r v i c e i s d u e i n a c c o r d a n c e
with the manufacturer’s servicing
schedule.
T h e p o i n t a t w h i c h t h e n e x t s e r v i c e i s
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- the distance travelled (in miles
(km)),
- the time elapsed since the last serv- ice (in months).
The distance remaining to be travelled
may be weighted by the time factor,
depending on the user’s driving habits.
Example: the display indicates that
7300 miles (kilometres) remain before
t h e n e x t s e r v i c e i s d u e .
The symbol “---” remains displayed
u n t i l t h e fi r s t s e r v i c e o f a n e w v e h i c l e
has been carried out.
Example: the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer.
Each time the ignition is switched on,
the display
“PERIODIC INSPECTION”
is displayed for a few seconds to
indicate that the service must be carried
out without delay.