wheel CITROEN C CROSSER 2010 User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010, Model line: C CROSSER, Model: CITROEN C CROSSER 2010Pages: 217, PDF Size: 6.48 MB
Page 112 of 217
VII
!
D R I V I N G
117
Operating faults
If the selected transmission mode dis-
p l a y fl a s h e s , t h e v e h i c l e s w i t c h e s a u t o -
matically to front "2WD" transmission
mode.
It is then no longer possible to select the
transmission mode using the control A . Do not subject the vehicle to exces-
sive conditions while driving.
As the engine torque is applied to
all four wheels, the condition of the
tyres has a considerable impact on
the performance of the vehicle.
Ensure that all four tyres are in good
condition.
Avoid driving the vehicle in sandy
or muddy areas or in other areas in
which the wheels could spin.
Spinning the wheels places the
transmission components under
pressure and could cause a serious
malfunction.
Do not drive the vehicle through
deep water.
Avoid driving over excessively un-
even terrain (risk of scraping under
the body or of grounding on crossing
a bridge).
Have your vehicle towed on a
fl a t b e d .
The vehicle must not be towed with
the front or rear wheels on the ground even if it is in front "2WD" (2 wheel
drive) mode.
If the message "SLOW DOWN" is dis-
played on the instrument panel, let the
transmission cool down then wait for the
display to clear before setting off again.
If "4WD" and "LOCK" are displayed
alternately and if "MAINTENANCE
REQUIRED" is displayed on the instru-
ment panel, the system has failed and
the safety system has been activated.
Contact a CITROËN dealer without delay.
Page 113 of 217
VII
D R I V I N G
118
Programming
Press button 1 .
Set the programmed speed by ac-
celerating to the required speed,
then press button 2 "COAST SET" .
CRUISE CONTROL
The controls of this system are grouped
together on the steering wheel.
1. "ON/OFF" button: activation/deacti-
vation of the cruise control mode.
2. "COAST SET" button: storing of a
driving speed and decreasing of the
cruising speed.
3. "ACC RES" button: increasing of
the cruising speed and recalling of
the stored speed.
4. "CANCEL" button: switching off of
the cruise control. When you press button
1 , the "CRUISE"
indicator comes on in the instrument
panel.
Steering mounted controls Display on the instrument panel
The cruise control cannot, in any cir-
cumstances, take the place of the
need to comply with speed limits or
of the vigilance and responsibility of
the driver.
System which automatically maintains
the vehicle speed at the value pro-
grammed by the driver, without any ac-
tion on the accelerator pedal.
The cruise control is
switched on
manually: the vehicle speed must be
25 mph (40 km/h) minimum and sec-
ond gear must be engaged in the case
of a manual gearbox.
The cruise control is switched off man-
ually, by an action on the brake or clutch
pedal or if the ASC system is triggered.
The programmed speed can be ex-
ceeded temporarily by pressing the
accelerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value.
Page 125 of 217
IX
!
P R A C T I C A L I N F O R M A T I O N
129
CHANGING A WHEEL
1. Wheelbrace.
Used to remove the wheel trim and t h e w h e e l fi x i n g b o l t s .
2. Jack.
Used to raise the vehicle.
3. Handle.
U s e d t o e x t e n d t h e j a c k .
4. R e m o v a b l e t o w i n g e y e .
R e f e r t o t h e " T o w i n g " p a r a g r a p h .
Other accessories
Wheel with trim
When removing the wheel , remove
t h e t r i m fi r s t u s i n g t h e h a n d l e 3 , p u l l i n g
at the notch.
W h e n r e fi t t i n g t h e w h e e l , r e fi t t h e t r i m
s t a r t i n g b y p l a c i n g i t s n o t c h F (indicated
o n t h e b a c k o f t h e t r i m ) o p p o s i t e t h e
valve G a n d p r e s s o n i t s o u t e r e d g e
w i t h t h e p a l m o f y o u r h a n d .
List of tools
W h e n c h a n g i n g a w h e e l , e n s u r e
t h a t t h e f o u r w h e e l s a r e o f i d e n t i -
c a l s p e c i fi c a t i o n a n d b r a n d .
W h e n s t o r i n g , t a k e c a r e t o s e c u r e
t h e t o o l b a g
D fi r m l y u s i n g t h e fi x i n g
band C .
Access to the tools
T h e t o o l s a r e s t o r e d i n t h e s t o r a g e c o m -
p a r t m e n t i n t h e b o o t r i g h t - h a n d t r i m .
T o g a i n a c c e s s t o t h e m :
o p e n t h e b o o t ,
t u r n b u t t o n A to the left,
remove the cover B ,
r e m o v e t h e fi x i n g b a n d C and take
o u t t h e t o o l b a g D c o n t a i n i n g t h e
tools,
t a k e t h e j a c k E i n y o u r h a n d a n d r e -
m o v e i t f r o m i t s fi x i n g p o s i t i o n .
Page 126 of 217
IX
P R A C T I C A L I N F O R M A T I O N
130
Fixing the "space-saver" spare
wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a l l o y
wheels, it is normal to notice that the
washers do not come into contact
w i t h t h e " s p a c e - s a v e r " s p a r e w h e e l
w h e n t i g h t e n i n g t h e b o l t s o n fi t t i n g .
T h e w h e e l i s r e t a i n e d b y t h e c o n i c a l
contact of each bolt.
Access to the spare wheel in the 7 seat configuration
The "space-
saver
" s p a r e w h e e l i s i n -
s t a l l e d o n t h e o u t s i d e , u n d e r t h e b o o t ,
s u p p o r t e d b y a m e t a l c a r r i e r .
T o g a i n a c c e s s t o t h e t o o l s , r e f e r t o t h e
" A c c e s s t o t h e t o o l s " p a r a g r a p h . Putting the wheel back in place
P u t t h e w h e e l b a c k i n p l a c e i n i t s
carrier.
Lift the carrier C a n d r e p o s i t i o n t h e
hook D .
O p e n t h e l o w e r t a i l g a t e ( r e f e r t o t h e
"Access" section).
R e m o v e t h e p l a s t i c c o v e r A u s i n g
the handle 3 .
U n s c r e w t h e s p a r e w h e e l c a r r i e r r e -
t a i n i n g b o l t B u s i n g t h e w h e e l b r a c e 1 .
C l o s e t h e l o w e r t a i l g a t e ( r e f e r t o t h e
"Access" section).
Lift the carrier C to detach the hook D
then allow it to lower.
T i g h t e n t h e s p a r e w h e e l c a r r i e r
r e t a i n i n g b o l t B f u l l y u s i n g t h e
wheelbrace 1 .
R e fi t t h e p l a s t i c c o v e r A , close the
l o w e r t a i l g a t e a n d s t o r e t h e t o o l s .
Removing the wheel
O p e n t h e t a i l g a t e a n d t h e l o w e r t a i l -
g a t e ( r e f e r t o t h e " A c c e s s " s e c t i o n ) .
T a k e o u t t h e h a n d l e 3 (refer to the
" A c c e s s t o t h e t o o l s " p a r a g r a p h ) .
Page 127 of 217
IX
P R A C T I C A L I N F O R M A T I O N
131
Access to the spare wheel in the 5 seat configuration
The pressed
steel
s p a r e w h e e l i s i n s t a l l e d o n t h e o u t s i d e , u n d e r t h e b o o t , s u p p o r t e d
b y a w i n c h a n d a p l a s t i c c a r r i e r .
T o g a i n a c c e s s t o t h e t o o l s , r e f e r t o t h e
" A c c e s s t o t h e t o o l s " p a r a g r a p h .
Fixing the pressed steel spare
wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a l l o y
wheels, it is normal to notice that the
washers do not come into contact
w i t h t h e p r e s s e d s t e e l s p a r e w h e e l
w h e n t i g h t e n i n g t h e b o l t s o n fi t t i n g .
T h e w h e e l i s r e t a i n e d b y t h e c o n i c a l
contact of each bolt.
Removing the wheel
O p e n t h e t a i l g a t e a n d t h e l o w e r t a i l -
g a t e ( r e f e r t o t h e " A c c e s s " s e c t i o n ) .
T a k e o u t t h e h a n d l e 3 (refer to the
" A c c e s s t o t h e t o o l s " p a r a g r a p h ) .
R e m o v e t h e p l a s t i c c o v e r A u s i n g
the handle 3 . Putting the wheel back in place
P u t t h e w h e e l b a c k i n p l a c e i n i t s
carrier.
Pass the hook C into the chain.
O p e n t h e l o w e r t a i l g a t e ( r e f e r t o t h e
"Access" section).
U n s c r e w t h e r e t a i n i n g b o l t B fully
u s i n g t h e w h e e l b r a c e 1 , t o u n w i n d
the winch cable.
C l o s e t h e l o w e r t a i l g a t e ( r e f e r t o t h e
"Access" section).
Detach the hook C from the chain.
U n w i n d t h e w i n c h c a b l e f u l l y t o m a k e
u n h o o k i n g o f t h e c h a i n e a s i e r .
T i g h t e n t h e w i n c h r e t a i n i n g b o l t B
f u l l y u s i n g t h e w h e e l b r a c e 1 .
R e fi t t h e p l a s t i c c o v e r A , close the
l o w e r t a i l g a t e a n d s t o r e t h e t o o l s .
Page 128 of 217
IX
P R A C T I C A L I N F O R M A T I O N
132
Parking the vehicle
Immobilise the vehicle where it does
n o t b l o c k t r a f fi c : i f p o s s i b l e , p a r k t h e
v e h i c l e o n l e v e l , s t a b l e a n d n o n -
s l i p p e r y g r o u n d .
A p p l y t h e p a r k i n g b r a k e , s w i t c h o f f
t h e i g n i t i o n a n d e n g a g e fi r s t g e a r t o
lock the wheels.
I f n e c e s s a r y , p l a c e a c h o c k u n d e r
t h e w h e e l d i a g o n a l l y o p p o s i t e t h e
w h e e l t o b e c h a n g e d .
N e v e r g o u n d e r n e a t h a v e h i c l e
r a i s e d u s i n g a j a c k ; u s e a s t a n d .
Removing a wheel List of operations
I f y o u r v e h i c l e i s e q u i p p e d w i t h s e c u -
r i t y w h e e l b o l t s ( e q u i p m e n t a v a i l a b l e
a s a n a c c e s s o r y ) fi t t h e s e c u r i t y s o c k -
et 5 on the wheelbrace 1 to slacken
t h e s e c u r i t y b o l t .
S l a c k e n t h e o t h e r b o l t s u s i n g t h e
wheelbrace 1 o n l y .
P l a c e t h e j a c k 2 in contact with one
of the two front A or rear B locations
p r o v i d e d o n t h e u n d e r b o d y , w h i c h -
ever is closest to the wheel to be
c h a n g e d .
E x t e n d t h e j a c k 2 u n t i l i t s b a s e p l a t e
i s i n c o n t a c t w i t h t h e g r o u n d . E n s u r e
t h a t t h e c e n t r e l i n e o f t h e j a c k b a s e
p l a t e i s d i r e c t l y b e l o w t h e l o c a t i o n A
or B u s e d .
R a i s e t h e v e h i c l e u n t i l t h e r e i s s u f fi -
c i e n t s p a c e b e t w e e n t h e w h e e l a n d
t h e g r o u n d t o a d m i t t h e s p a r e ( n o t
p u n c t u r e d ) w h e e l e a s i l y .
Remove the bolts and store them in
a c l e a n p l a c e .
Remove the wheel.
Page 129 of 217
IX
P R A C T I C A L I N F O R M A T I O N
133
After changing a wheel
W h e n u s i n g t h e " s p a c e - s a v e r " s p a r e
w h e e l , d o n o t e x c e e d a s p e e d o f
5 0 m p h ( 8 0 k m / h ) .
H a v e t h e t i g h t e n i n g o f t h e b o l t s a n d
t h e p r e s s u r e o f t h e s p a r e w h e e l
c h e c k e d b y a C I T R O Ë N d e a l e r w i t h -
o u t d e l a y .
H a v e t h e p u n c t u r e d w h e e l r e p a i r e d
a n d r e p l a c e i t o n t h e v e h i c l e a s s o o n
a s p o s s i b l e .
Fitting a wheel List of operations
L o w e r t h e v e h i c l e f u l l y .
F o l d t h e j a c k 2 and detach it.
T i g h t e n t h e s e c u r i t y b o l t u s i n g t h e
wheelbrace 1 fi t t e d w i t h t h e s e c u r i t y
socket 5 ( i f y o u r v e h i c l e i s e q u i p p e d
w i t h s e c u r i t y w h e e l b o l t s ) .
T i g h t e n t h e o t h e r b o l t s u s i n g t h e
wheelbrace 1 o n l y .
S t o r e t h e t o o l s ( r e f e r t o t h e p a r a g r a p h
"Access to the tools").
Fitting snow tyres
I f y o u e q u i p y o u r v e h i c l e w i t h s n o w
t y r e s fi t t e d o n s t e e l w h e e l r i m s ,
s p e c i a l b o l t s a v a i l a b l e f r o m y o u r
C I T R O Ë N d e a l e r must b e u s e d .
P u t t h e w h e e l i n p l a c e o n t h e h u b .
S c r e w i n t h e b o l t s f u l l y b y h a n d .
P r e - t i g h t e n t h e s e c u r i t y b o l t u s -
i n g t h e w h e e l b r a c e 1 fi t t e d w i t h
t h e s e c u r i t y s o c k e t 5 ( i f y o u r v e h i -
c l e i s e q u i p p e d w i t h s e c u r i t y w h e e l
bolts).
P r e - t i g h t e n t h e o t h e r b o l t s u s i n g t h e
wheelbrace 1 o n l y .
Page 133 of 217
IX
P R A C T I C A L I N F O R M A T I O N
137
Changing integrated direction
indicator side repeaters Changing foglamp bulbs (5)
P u s h t h e r e p e a t e r A towards the
rear and detach it.
U n c l i p t h e r e p e a t e r .
D i s c o n n e c t t h e r e p e a t e r c o n n e c t o r
a n d c h a n g e t h e r e p e a t e r .
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n
reverse order.
T o o b t a i n r e p e a t e r s , c o n t a c t a C I T R O Ë N
dealer.
T u r n t h e w h e e l f u l l y o u t f o r e a s y
a c c e s s t o t h e fl a p A located in the
wheelarch.
U s i n g a s c r e w d r i v e r , r e m o v e t h e f o u r
c l i p s B located in the wheelarch.
Page 134 of 217
IX
P R A C T I C A L I N F O R M A T I O N
1 3 8
U s i n g a s c r e w d r i v e r , r e m o v e t h e
t h r e e c l i p s C located below the
b u m p e r .
L i f t t h e a c c e s s fl a p D located in the
wheelarch and slide it downwards.
Disconnect the connector E .
T u r n t h e b u l b F t o t h e l e f t a n d r e -
move it.
T o r e fi t , c a r r y o u t t h e s e o p e r a t i o n s i n
reverse order.
Page 147 of 217
IX
!
!
P R A C T I C A L I N F O R M A T I O N
151
TOWING
Access to the tools
Having your vehicle towed on a flatbed
B e l o w t h e f r o n t b u m p e r , i n s t a l l t h e
t o w i n g s y s t e m o n t h e t o w i n g e y e 1 .
T h e t o w i n g e y e a n d t h e t o o l s a r e s t o r e d
i n t h e s t o r a g e c o m p a r t m e n t i n t h e r i g h t -
hand boot trim.
T o g a i n a c c e s s t o t h e m :
o p e n t h e b o o t ,
t u r n b u t t o n A to the left,
remove the cover B ,
r e m o v e t h e fi x i n g b a n d C and take
o u t t h e t o o l b a g D c o n t a i n i n g t h e
tools,
t a k e t h e t o w i n g e y e a n d t h e t o o l s r e -
q u i r e d o u t o f t h e t o o l b a g . P l a c e t h e g e a r l e v e r i n n e u t r a l .
Always have the vehicle
t o w e d o n a fl a t b e d .
Never have the vehicle towed with
t h e f o u r w h e e l s o n t h e g r o u n d , t h i s
c o u l d d a m a g e t h e t r a n s m i s s i o n .
T h e v e h i c l e m u s t n o t b e t o w e d w i t h
t h e f r o n t o r r e a r w h e e l s o n t h e g r o u n d
even if it is in front "2WD" (2 wheel
drive) mode.
Towing another vehicle
O n t h e r e a r b u m p e r , r e m o v e t h e
c o v e r b y p u l l i n g a t t h e b o t t o m u s i n g
t h e j a c k h a n d l e 2 .
S c r e w i n t h e t o w i n g e y e f u l l y u s i n g
the wheelbrace 3 .
Install the towbar.
S w i t c h o n t h e h a z a r d w a r n i n g l a m p s
on the towed vehicle.
W h e n b e i n g t o w e d w i t h t h e e n -
g i n e o f f , t h e r e i s n o l o n g e r a n y
b r a k i n g o r s t e e r i n g a s s i s t a n c e .