ignition CITROEN C CROSSER DAG 2009 User Guide

I N S T R U M E N T S a n d C O N T R O L S
I
31
SERVICE INDICATOR Resetting the service indicator
to zero
Your CITROËN dealer carries out this
operation after each service.
If you have carried out your vehicle’s
service yourself, the zero reset
procedure is the following:

 switch off the ignition,

 press the INFO button several times
in succession until the service indi-
cator is displayed.

 press and hold the INFO button for
a few seconds until the spanner
fl ashes .

 press the INFO button while the
spanner is fl ashing to change the
display “---” to “CLEAR” then the
time remaining before the next serv-
ice is due is displayed.
Service overdue
Operation
When the ignition is switched on, you
must press the INFO button several
times in succession until the service
indicator is displayed. The distance
recorder display line indicates the
number of miles (kilometres) remaining
and the time elapsed line indicates the
number of months remaining before the
next service is due.
After a certain distance and a
certain time, the displaying of “---”
is reinitialised and the display
indicates the time remaining before
the next service is due.
System which informs the driver when
the next service is due in accordance
with the manufacturer’s servicing
schedule.
The point at which the next service is
due is calculated from the last service
indicator zero reset.
It is determined by two parameters:
- the distance travelled (in miles
(km)),
- the time elapsed since the last serv- ice (in months).
The distance remaining to be travelled
may be weighted by the time factor,
depending on the user’s driving habits.
Example: the display indicates that
7300 miles (kilometres) remain before
the next service is due.
The symbol “---” remains displayed
until the fi rst service of a new vehicle
has been carried out.

Example: the display indicates that the
service is overdue. This service must
be carried out by a CITROËN dealer.
Each time the ignition is switched on,
the display
“SCHEDULED SERVICE”
is displayed for a few seconds to
indicate that the service must be carried
out without delay.

I N S T R U M E N T S a n d C O N T R O L S
I
32
System which provides current
information about the route travelled.
TRIP COMPUTER Average
consumption
(l/100km or km/l or
mpg)
This is the average
quantity of fuel consumed
since the last zero reset.
This fi gure may increase following a
change in the style of driving or the
relief resulting in a reduction in the
current consumption. Average speed
(km/h or mph)
This is the average
speed calculated since
the last zero reset. Resetting the information to
zero
Automatic
If the ignition remains in the “ACC”

(Accessories) position for at least
4 hours, the average consumption value
is reset to zero automatically.
If dashes “---” are displayed for long
periods in place of the digits while
driving, contact a CITROËN dealer. Current
consumption
(l/100km or km/l or
mpg)
This is the average
quantity of fuel
consumed during the
last few seconds of
driving.
Data displays
With the ignition on, press the
INFO
button on the fascia, to the left of the
instrument panel, several times in
succession to display the different
information:
- the average consumption,
- the average speed,
- the current consumption. When the required information is
displayed, press the
INFO button for
more than two seconds.
When the ignition is switched on, the
zero reset switches automatically from
manual mode to automatic mode.

I N S T R U M E N T S a n d C O N T R O L S
I
33

When the vehicle is
stationary , it allows
the user to change the
following parameters:
- the choice of the reini- tialisation of the aver-
age consumption and
average speed,
- the fuel consumption unit,
- the temperature display unit,
- the display language,
- activation/deactivation of the INFO
button sound,
- the break (rest) reminder display in- terval,
- restore the manufacturer’s param- eters.
FUNCTION PARAMETERS
System which provides access to
certain function parameters.
In order to change the settings,
it is essential that you stop
the vehicle and switch on the
ignition.
Apply the handbrake and place the
gear lever in neutral.

When the vehicle is moving ,
the functions setting display is not
displayed when you press the INFO
button.

With the ignition on , press the INFO
button on the fascia, to the left of the
instrument panel, several times in
succession until the “SETTING MENU”
screen is displayed. Operation

 press and hold the INFO button for
a few seconds to display the menus
screen. Press and hold the
INFO button
for a few seconds to return to the
previous screen.
When the menus screen is displayed,
if no operation is carried out within
15 seconds, the function parameters
screen is displayed.

 on the menus screen, press the

INFO button to select a function
from the list:

MENU 1/2 :
- 1 - 2 (choice of the reinitialisation of
the average consumption and aver-
age speed),
- UNIT (choice of the fuel consump-
tion units),
- choice of the temperature display
unit ,
- LANGUAGE (choice of the display
language),

MENU 2/2:
- a/b (choice of displaying a different
language on the instrument panel
display and the navigation display),
- activation / deactivation of the
INFO
button sound ,
- ALERT (changing of the “BREAK
ADVISED” break reminder display
interval),
- REINITIALISE (restore the manu-
facturer’s parameters). Choice of the reinitialisation of
the average consumption and
average speed
You can choose between two average
consumption and average speed
reinitialisation modes:
- automatic reinitialisation
( choice 1) ,
- manual reinitialisation (choice 2) .
On the menus screen:

 press the INFO button to select:

 press and hold the INFO button for
a few seconds to switch in succes-
sion from reinitialisation mode
1

(automatic) to reinitialisation mode

2 (manual) .
The mode selected is confi rmed.

I N S T R U M E N T S a n d C O N T R O L S
I
36
Restoring the manufacturer’s
parameters (REINITIALISE)
You can restore all of the manufacturer’s
settings for all of the functions.
On the menus screen:

 press the INFO button to select

“REINITIALISE”
(located on menu
2/2) .

 press and hold the INFO button for

at least 5 seconds .
An audible signal is heard and all of the
manufacturer’s settings are restored for
all of the functions. The manufacturer’s settings are: LIGHTING RHEOSTAT
With the lights on or off, press the button
to change the intensity of the lighting of
the instruments and controls in “day” or
“night” mode.
When the lighting reaches the maximum
setting, press again to change to the
minimum setting.
When the lighting reaches the required
intensity, release the button.
The setting is saved when the ignition
switch is turned to OFF. An audible signal is heard and the
intensity of the lighting increases
each time the button is pressed.
System for manual adjustment of the
brightness of the instruments and
controls in relation to the exterior
brightness.

Functions
Manufacturer’s
setting
Reinitialisation
of the average
consumption and
average speed
1 (automatic)
Fuel consumption
units
L/100 km
Temperature
display unit
°C
Display language ENGLISH
INFO button
sound
ON (activated)
Displaying of
the “BREAK
ADVISED”
message

OFF (deactivated)

I N S T R U M E N T S a n d C O N T R O L S
I
38
Set the time using the buttons as
indicated below:

 with the ignition on or in the ACC
(Accessories) position, press and
hold the CLOCK button until the
time display fl ashes.
 Press the appropriate button to set
the time:

Button H: setting of the hour
The hours digits scroll when you press
this button.

Button M: setting of the minutes
The minutes digits scroll when you
press this button.

Button :00: resetting of the minutes to
zero.
- from 1 to 29 min
: rounded down to
the previous hour,
- from 30 to 59 min: rounded up to
the next hour.
Manual mode
Automatic mode
In this mode, setting is automatic using
the signal from the RDS radio stations.
 After setting the time, press the

DISP button; the time display stops
fl ashing.
The digital clock does not display
seconds.
When the “minutes” display is set or
reset to zero, the clock starts at the
zero second of the minute selected.
The time setting is lost if the battery
is disconnected.

 Turn button B “TUNE” to the left or
to the right to select “CT ON” (auto-
matic mode) or “CT OFF” (manual
mode).

 After selecting the mode, you can
exit the “Functions setting mode”
menu by pressing button B “TUNE”
for approximately 2 seconds.
If no action is carried out within
10 seconds, the system will exit
the “functions setting mode” menu
automatically.

C O M F O R T
II
46
Air conditioning On / Off (5)

 Press button 5 to activate the air
conditioning.
The indicator light comes on.
Intake of exterior air /
Recirculation of interior
air (4)
This function insulates the passenger
compartment from exterior odours and
smoke.

 Press button 4 to select the air in-
take mode.
When the indicator light on button 4 is
off, the exterior air intake function is ac-
tivated.
When the indicator light on button 4 is
on, the intake of exterior air is deacti-
vated and the system is in air recircula-
tion mode.
Do not drive for long periods in interior
air recirculation mode, except in truly
exceptional atmospheric conditions. Personalisation of the Exterior air
intake / Interior air recirculation
function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to change
the air intake mode at any time.
Personalisation of the Air
Conditioning On / Off function
This function is controlled automati-
cally. However, you can deactivate its
automatic control if you wish to activate
or deactivate the air conditioning at any
time.
The settings are retained, even after
switching off the ignition.
Changing the status
Press the Air intake / Interior air recircu-
lation button for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator light fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator light fl ashes three times.
Automatic control active
If the air distribution adjustment dial and
the air fl ow adjustment dial are placed
in the “AUTO” position, the Air intake /
Interior air recirculation function is also
controlled automatically.
Automatic control inactive
Even if the air distribution adjustment
dial and the air fl ow adjustment dial are
placed in the “AUTO” position, the Air
intake / Interior air recirculation function
is no longer controlled automatically.
Changing the status
Press the Air Conditioning On / Off but-
ton for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator light fl ashes three times.
When the status changes from inactive
to active, two bleeps are heard and the
indicator light fl ashes three times.
Automatic control active
If the air distribution adjustment dial and
the air fl ow adjustment dial are placed
in the “AUTO” position, or if the temper-
ature control dial is set to the minimum
temperature, the air conditioning sys-
tem is controlled automatically.
Automatic control inactive
The air conditioning system is no longer
controlled automatically.

C O M F O R T
II
59
EXTERIOR MIRRORS
Electric folding / unfolding
- from inside, with the ignition switch in the “ON” or “ACC” position

 by pressing the control C .
- from inside, with the ignition switch in the “LOCK” position:

 by pressing the control C, within
30 seconds.
- from outside using the remote control:

 by pressing the “closed padlock”
button briefl y 3 times to fold
them,

 by pressing the “open padlock”
button briefl y 3 times to unfold
them.
Adjustment
The mirrors can be adjusted when the
ignition switch is in the “ON” or “ACC”
position.

 Move control
A to the right or to
the left to select the corresponding
mirror.

 Direct control
B in all four direc-
tions to adjust the mirror.
When adjustment is complete, return
control A to the central position. If you switch the engine off then re-
start it with the mirrors folded, they
will unfold automatically when the
vehicle reaches 20 mph (30 km/h).
If the mirrors have been folded man-
ually or electrically after starting the
engine, they are not unfolded auto-
matically.
In this case:

 Press the control C to unfold
them. If you have folded the mirrors
using the control
C , you must
use this control to unfold them,
otherwise the mirrors will not be
locked correctly.

The folding and unfolding of the exte-
rior mirrors can be confi gured via the
colour display “Equipment” menu or
deactivated by a CITROËN dealer.
The mirrors can also be folded manually.

C O M F O R T
II
64
Lower glove box
This is fi tted with a lock.
To unlock it, turn the key to the left.
To open it, pull the handle A .
To close it, push the lid up.
To lock it, turn the key to the right.
It is fi tted with a pen holder and a card
holder.
It is lit on opening when the lights stalk
is activated. Lighter
12 volt socket (120 W max)
When the ignition switch is in the “ON”
or “ACC” position, press the lighter.
After a moment you hear a click when
the lighter pops out.
When the lighter socket is used to con-
nect electrical equipment, ensure that
this equipment operates correctly with
a voltage of 12 volts and has an electri-
cal power of 120 W maximum.
The prolonged use of electri-
cal equipment without running
the engine may discharge the
battery. Armrest with storage compartments
12 volt socket (120 W max)
Upper storage compartment
Pull the right-hand lever to open the
storage compartment lid, which serves
as an armrest.
To close, fold down the lid until it locks.

C O M F O R T
II
65
Removable ashtray
Pull the cover to open the ashtray.
To empty, remove the ashtray by pulling
it upwards.
Lower storage compartment
Pull the left-hand lever to open the lid.
To close, fold down the lid until it locks.
12 volt socket (120 W max)
This operates when the ignition switch is
in the “LOCK”, “ACC” or “ON” position.
Open the cover to gain access to the
socket.
Check that the electrical equip-
ment operates with 12 volts
and that its maximum electri-
cal power is 120 W.
When you use the two sockets
at the same time, ensure that the two
items of equipment together operate
with 12V and that their combined
electrical power is 120W maximum.
The prolonged use of electrical
equipment without running the en-
gine may discharge the battery.

C O M F O R T
II
70
12 volt socket (120 W max)
This operates when the ignition switch
is in the “ON” or “ACC” position.
Lift the cover to gain access to the
socket. Check that the electrical equip-
ment operates with 12 volts
and that its maximum electri-
cal power is 120 W.
The prolonged use of electri-
cal equipment without running the
engine may discharge the battery. Stowing rings
There are four stowing rings in the boot
for securing luggage:
- two rings are located on the boot
fl oor,
- two rings are located on the rear side pillars.
* On 5-seat version only.
Raise the boot fl oor to gain access to
this compartment.
Right-hand side enclosed storage
compartment
This storage compartment contains the
tools for changing a wheel. Storage compartment in the fl oor *