warning CITROEN C-ELYSÉE 2012 Owner's Guide

84
Driving
Manual operation
)Select position M for sequentialchanging
o
f the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the
instrument panel.

Invalid value during manual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position Por N
to place the gearbox in neutral.
In both cases, apply the parking brake to
immobilise the vehicle.

Operating fault
When the ignition is on, the
lighting of this warning lamp,
accompanied by an audible signal and amessage in the multifunction screen, indicates
a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the Pposition toanother position when the battery isflat.
To reduce fuel consumption when at
a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.

If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the message disappears.

90
Driving
In bad weather or in winter, ensure that the sensors are not covered with mud, ice or snow. When reverse gear isengaged, an audible signal (long beep)indicates that the sensors may be dirty.
Cer tain sound sources (motorcycle,lorry, pneumatic drill, etc.) may trigger the audible signals of the parking
sensor system.
In th
e event of a malfunction of
the system, when reverse gea
r
is engaged this warning lamp
is displayed in the instrument panel and/or a message appears in the screen, accompanied
by an audible signal (short beep).
Contact a CITROËN dealer or a qualified
wor
kshop.

Operating fault
The function will be deactivated automatically if a trailer is being towed or a bicycle carrier is fitted (vehicle fitted with a towbar or bicycle carrier recommended by CITROËN).

Deactivation / Activation of the
rear parking sensors
The function is deactivated or
activated via the vehicle con
figuration menu.
The status of the function is stored
when the ignition is switched off.
For more in
formation on access to the parkingsensors menu, refer to the "Personalisation -Configuration" par t of the "Instruments andcontrols" section.

100
Safety











Direction indicators
Selection of the left or right direction indicators
to signal a change of direction of the vehicle. )Left: lower the lighting stalk beyond thepoint of resistance.)Right: raise the lighting stalk beyond thepoint of resistance.
"Motorway" function
)Press briefly upwards or downwards,
without going beyond the point of resistance; the direction indicators will flash 3 times.








Hazard warning lamps
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on
the deceleration, the hazard warning lampscome on automatically.
The
y switch off automatically the first time youaccelerate. )
You can also switch them off by pressing
the button.
) Press this button, the direction indicatorsflash.
They can operate with the ignition off.









Horn
)Vehicle with driver's airbag: press the central part of the steering wheel.
or )Vehicle without driver's airbag: press theend of the lighting control stalk.
Audible warning system to alert other road
users to an imminent danger.

Use the horn moderately and only in the following circumstances:


- immediate danger,

- over taking a cyclist or pedestrian,

- approaching a location lackingvisibility.
A visual warnin
g by means of the directionindicators to alert other road users to a vehiclebreakdown, towing or accident.

101
7
Safety
Group of supplementary systems which helpyou to obtain optimum braking in completesafety in emergency situations:


- anti-lock brakin
g system (ABS),

- electronic brake force distribution (EBFD),

- emergency braking assistance (EBA).

















Braking assistance systems


Anti-lock braking system
and electronic brake force
distribution

Linked systems which improve the stability andmanoeuvrability of your vehicle when braking,
in par ticular on poor or slippery surfaces.

Activation

The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself felt by slight vibration of the brake pedal.
Operating fault
Emergency braking assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure more
quickly, thus reducing the stopping distance.
When braking in an emergency, press firmly without releasing the pressure.


When braking in an emergency, press very firmly without releasing thepressure.
When replacing wheels (tyres andrims), ensure that they conform to the manufacturer's recommendations. I
f this warning lamp comes on,
accompanied by an audible signaland a message in the screen, it indicates a malfunction of the anti-lock braking
system which could result in loss of control of
the vehicle when braking.
I
f this warning lamp comes on,
together with the STOP
and ABSwarning lamps, accompanied by anaudible signal and a message in the screen, it indicates a malfunction of the electronic brake
force distribution which could result in loss of control of the vehicle when braking.
You must stop as soon as it is safe to do so.In either case, contact a CITROËN dealer or aqualified workshop.
Activation
It is triggered by the speed at which the brake pedal is pressed.
The effect of this is a reduction in theresistance of the pedal and an increase in
braking efficiency.
Coasting with the engine off results in aloss of power assistance for braking.

102
Safety
Anti-slip regulation (ASR)
and electronic stability
programme (ESP)
The anti-slip regulation (also known as Traction Control) optimises traction to prevent skidding
of the wheels, by acting on the brakes of thedriving wheels and on the engine.
The electronic stability programme acts on the
brake o
f one or more wheels and on the engine to
keep the vehicle on the trajectory required by the
driver, within the limits of the laws of physics.
This is indicated b
y flashing of this
warning lamp in the instrument panel.



The ASR /ESP systems offer exceptional safety in normal driving, butthis should not encourage the driver to take extra risks or drive at high speed.
The correct functioning of these systems depends on obser vation of the manufacturer's recommendations regarding the wheels (tyres and rims),the braking components, the electronic components and the assembly and repair procedures used by theCITROËN dealer network.
After an impact, have these systems checked by a CITROËN dealer or a qualified workshop.



Operating fault

Illumination of the warning lamp,
accompanid b
y a message in the screen indicates a malfunction of
these systems.
Reactivation
These systems are reactivated automatically every time the ignition is switched of, or from
30 mph (50 km/h).) Press this button again to reactivate them
manually.
The lamp in the button goes off.
The symbol going off in the instrument panel
indicates the reactivation of the ASR and ESP
s
ystems.
Deactivation
In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft
ground, ...), it may be advisable to deactivate
the ASR and ESP systems, so that the wheelscan move freely and regain grip.














Trajectory control systems
Activation
These systems are activated automatically each time the vehicle is started.
They come into operation in the event of a grip
or trajectory problem.The displa
y of this symbol indicates
that the ASR and ESP systems are deactivated.
) Press this button button, located on
the dashboard (driver's side), until the corresponding symbol appears in the
instrument panel screen.
The lamp in the button comes on. Contact a CITROËN dealer or a qualified
workshop to have the ASR /ESP s
ystems checked.


Coasting with the engine off results in a loss of power assistance for the steering.

103
7
Safety
Seat belts


Front seat belts
Fastening
)
Pull the strap, then inser t the tongue in thebuckle. )
Check that the seat belt is fastened correctly by pulling the strap.

Unfastening
)
Press the red button on the buckle. )
Guide the seat belt as it is reeled in.
Th
e front seat belts are fitted with apretensioning and force limiting system.
This system improves safety in the frontseats in the event of a front or side impact.
Depending on the severity of the impact, thepretensioning system instantly tightens the seat
belts against the body of the occupants.
The pretensioning seat belts are active when
the ignition is on.
The force limiter reduces the pressure of the seat belt on the chest of the occupant, so
improving their protection.
When the ignition is switched on,
this warning lamp comes on in the
instrument panel, if the driver has notfastened their seat belt.

Seat belt not fastened / unfastened warning lamp

From approximately 12 mph (20 km/h)this warning lamp flashes for two minutes
accompanied by an audible signal of increasingvolume. Once these two minutes have elapsed,
this warning lamp remains on until the driver fastens their seat belt.
This warning lamp also comes on in the
instrument panel if the driver and/or front
passenger unfastens their seat belt while
driving.

105
7
Safety
The driver must ensure that passengers usethe seat belts correctly and that they are allrestrained securely before setting off.
Wherever you are seated in the vehicle, always fasten your seat belt, even for short journeys. Do not interchange the seat belt buckles asthey will not fulfil their role fully.
The seat belts are fitted with an inertia reel permitting automatic adjustment of the length of the strap to your size. The seat belt isstowed automatically when not in use.
Before and after use, ensure that the seatbelt is reeled in correctly.
The lower par t of the strap must bepositioned as low as possible on the pelvis.
The upper par t must be positioned in the hollow of the shoulder.
The inertia reels are fitted with an automatic locking device which comes into operation inthe event of a collision, emergency braking or if the vehicle rolls over. You can releasethe device by pulling firmly on the strap and releasing it so that it reels in slightly.
Recommendations for children
Use a suitable child seat if the passenger isless than 12 years old or shor ter than one
and a half metres. Never use the same seat belt to secure morethan one person. Never allow a child to travel on your lap.

In order to be effective, a seat belt must:


- be tightened as close to the body as possible,


- be pulled in front of you with a smooth movement, checking that it does nottwist,

- be used to restrain only one person,

- not bear any trace of cuts or fraying,

- not be converted or modified to avoid affecting its per formance.
In accordance with current safety regulations, for all repairs on your vehicle, go to a qualified workshop with the skills and equipment needed, which a CITROËN dealer is able to provide.
Have your seat belts checked regularly by a CITROËN dealer or a qualified workshop, particularly if the straps show signs of damage.
Clean the seat belt straps with soapywater or a textile cleaning product, sold by CITROËN dealers.
After folding or moving a seat or rear bench seat, ensure that the seat belt is positioned and reeled in correctly.
In the event of an impact
Depending on the nature and seriousness of the impact
, thepretensioning device may be deployedbefore and independently of the airbags.Deployment of the pretensioners isaccompanied by a slight discharge of harmless smoke and a noise, due to theactivation of the pyrotechnic cartridgeincorporated in the system.In all cases, the airbag warning lamp comes on.Following an impact, have the seat belts system checked, and if necessary replaced,by a CITROËN dealer or a qualified workshop.

107
7
Safety

Deactivation
This warning lamp comes on in theinstrument panel when the ignition is
on and until the airbag is reactivated.
To assure the safety of your child,the passenger's front airbag must be deactivated when you install a "rear facing" child seat on the front passenger seat.Other wise, the child would risk beingseriously injured or killed if the airbag were deployed.


If even one of the two airbag warning lamps comes on continuously, donot install a child seat on the frontpassenger seat.
Have it checked by a CITROËN dealer or qualified workshop.

Reactivation
Operating fault
If this warning lamp comes on in the
instrument panel, accompanied by an audible warning and a message in the
screen, contact a CITROËN dealer or a qualified
workshop to have the s
ystem checked. The airbags mayno longer be deployed in the event of a serious impact.
If this warning lamp flashes, contacta CITROËN dealer or a qualified
workshop. The passenger's front airbag may no longer be deployed in
the event of a serious impact.
Only the passenger's front airbag can be deactivated:)Inser t the key into the passenger airbag
deactivation switch,)turn it to the "OFF"position, )then, remove the key keeping the switch in
the new position.

When
you remove the child seat, with
the ignition on, turn the switch to the "ON"position to reactivate the airbag and so assure
the safety of your front passenger in the event
of an impact.

108
Safety
Lateral airbags
Deployment
The lateral airbags are deployed unilaterally in the event
of a serious side impact applied to all or par t of the side
impact zone B , perpendicular to the longitudinal centreline
of the vehicle on a horizontal plane and directed from the outside towards the inside of the vehicle.
The lateral airbag contributes towards the protection of thefront occupant of the vehicle, between the lower thoraxand the head.
System which protects the driver and frontpassenger in the event of a serious side impact
in order to limit the risk of injury to the chest,
between the hip and the shoulder.
Each lateral airba
g is fitted in the seat backrest
frame, door side.

Impact detection zones
A.
Front impact zone.
B. Side impact zone.

I
f this warning lamp comes on in the instrument panel, accompanied by an
audible signal and a message in the
screen, contact a CITROËN dealer
or a qualified workshop to have the
s
ystem checked. The airbags may nolonger be deployed in the event of a
serious impact.


Operating fault


In the event of a minor impact or bump on the side of the vehicle or if the vehicle rolls over, the airbag may not be deployed.
In the event of a rear or front collision, the airbag is not deployed.

129
9
Practical information
Removing a wheel

Parking the vehicle

Immobilise the vehicle where it does notblock traffic: the ground must be level, stable and not slippery. Apply the parking brake, switch off the
ignition and engage first gear *
to blockthe wheels. Check that the parking brake warninglamps in the instrument panel come on.
The occupants must get out of the vehicle and wait where they are safe.
Ensure that the jack is correctly positioned at one of the vehicle's jacking points.
Incorrect use of the jack could cause the vehicle to drop.
Never go underneath a vehicle raised using a jack; use an axle stand.


List of operations
)
Remove the bolt cover from each of
the bolts using the tool 3 (according to equipment).)
Slacken the bolts using the wheelbrace 1only.

Do not use:
- the jack for any other purpose thanlifting the vehicle,- a jack other than the one suppliedby the manufacturer.




*
position R
for an electronic
gearbox; Pfor an automatic gearbox.