Control CITROEN C-ELYSÉE 2018 Handbook (in English)

18
Warning / indicator lampStateCause Action / Observations
Front foglamps Fixed. The front foglamps have been
switched on using the ring on the
lighting control stalk. Turn the ring on the lighting control stalk rear ward
once to switch off the front foglamps.
Left-hand
direction
indicator Flashing with audible
signal.
The lighting control stalk has been
moved down.
Right-hand
direction indicatorFlashing with audible
signal.The lighting control stalk has been
moved up.
Dipped beam
headlamps Fixed.
The lighting control stalk is in the
"Dipped beam headlamps" position.
Main beam
headlamps Fixed.
The lighting control stalk has been
pulled towards you. Pull the stalk to return to dipped beam headlamps.
Foot on the
clutch Fixed.
In STOP mode of Stop & Start, the
transition to START mode has been
rejected because the clutch pedal is
not fully pressed down. With a manual gearbox, you must declutch fully to
allow the change to engine START mode.
Foot on the
brake pedal Fixed.
With an automatic gearbox, you have
forgotten to press the brake pedal to
move out of position P.With the engine running, before releasing the parking
brake you must press the brake pedal to unlock the
automatic gear selector lever and move out of the P
position.
Instruments

21
AdBlue® fluid range
indicators
Once the AdBlue® tank is on reser ve or after
detection of a fault with the SCR emissions
control system, when the ignition is switched
on, an indicator displays an estimate of the
distance that can be covered, the range, before
engine starting is prevented.
In the event of a simultaneous system fault and
low AdBlue
® level, the shortest range figure is
the one displayed.
In the event of the risk of
non-starting related to a
lack of AdBlue
®
The engine starting inhibition system
required by regulations is activated
automatically once the AdBlue
® tank is
e m pt y.
Range greater than 1,500

miles (2,400 km)
When switching on the ignition, there is no
automatic display of the range in the instrument
panel.
Resetting the service indicator
After each service, the service indicator must
be reset to zero.
Following this operation, if you wish to
disconnect the battery, lock the vehicle
and wait at least five minutes for the zero
reset to be taken into account.
Retrieving the service
information
You can access the ser vice information at any
time.
F
P
ress the trip distance recorder reset
button. The ser vice information is displayed
for a few seconds, then disappears.
The procedure for resetting to zero is as
follows:
F

S

witch off the ignition.
F

P

ress and hold the trip distance recorder
reset button.
F

S

witch the ignition on; the distance recorder
display starts a countdown.
F

R

elease the button when =0

is displayed;
the spanner disappears.
1
Instruments

23
If it is a temporary fault, the alert
disappears during the next journey,
after auto diagnosis checks of the SCR
emissions control system.
During the permitted driving phase
(between 650
and 0 miles (1,100 km and
0


km))
While driving, the message is displayed every
30

seconds while the fault with the SCR
emissions control system persists.
The alert is repeated when switching on the
ignition. Starting prevented
You have exceeded the authorised driving
limit: the starting inhibition system does
not allow the engine to be started.
To be able to restart the engine, you must call
on a CITROËN dealer or a qualified workshop.In the event of a fault with
the SCR emissions control
system
An engine starting inhibition device is
activated automatically after you have
driven a further 650 miles (1,100 km)
following confirmation of a fault with the
SCR emissions control system. Have the
system checked by a CITROËN dealer or
a qualified workshop as soon as possible.
In the event of the detection of a fault
These warning lamps come on, accompanied
by an audible signal and the display of the
message "Emissions fault".
The alert is triggered while driving as soon
as the fault is detected for the first time, then
when switching on the ignition for subsequent
journeys, while the fault persists. If a fault with the SCR system is confirmed
(after 30
miles (50 km) covered with the
permanent display of the message signalling
a fault), these warning lamps come on and the
AdBlue warning lamp flashes, accompanied
by an audible signal and the temporary display
in the instrument cluster of NO START IN
and a distance, indicating the driving range
expressed in miles or kilometres before engine
starting is prevented – (e.g. "NO START IN
350
miles" means "Starting will be prevented in
350


miles").You should go to a CITROËN dealer or a
qualified workshop as soon as possible.
Other wise you will not be able to restart the
vehicle.
When switching on the ignition, these warning
lamps comes on and the AdBlue warning lamp
flashes, accompanied by an audible signal and
the temporary display of "NO START IN" and
0
miles or kilometres on the instrument panel –
("NO START IN 0
miles" means "Starting
prevented").
1
Instruments

25
Audio system / Bluetooth With CITROËN Connect Radio
F Select the "Settings" menu.
F
Sel
ect "Date and time ".
F

Sel
ect the " Date" or "Time " tab.
F

C
hoose the display formats.
F

C
hange the date and/or time using the
numeric keypad.
F

C
onfirm with " OK".
The system does not automatically
manage the change between winter and
summer time (depending on country).
With CITROËN Connect Nav
Adjustment of the time and date is only
available if synchronisation with GPS is
deactivated.
F

Sel
ect the " Settings " menu.
F

P
ress the " OPTIONS " button to go to the
secondary page.
F

Sel
ect "Setting the time- date". F

Sel
ect the "
Date" or "Time " tab.
F
A
djust the date and/or time using the
numeric keypad.
F
C
onfirm with "
OK".
Additional adjustments
You can choose:
-
T o change the display format of the date
and time (12h/24h).
-

T
o change the time zone.
-

T
o activate or deactivate synchronisation
with the GPS (UTC).
The system does not automatically
manage the change between winter and
summer time (depending on country).
The change between winter and summer
time is done by changing the time zone.
Operate the audio system buttons in the
following order:
F

P

ress the ‘ MENU’ button.
F

U

sing the arrows, select the
" Personalisation- Configuration " menu
and confirm by pressing the control knob.
F

U

sing the arrows, select the " Screen
configuration " menu then confirm.
F

U

sing the arrows, select the " Set date and
time " menu then confirm.
F

S

elect the setting then confirm.
F

M

odify the setting then confirm again to
save the change.
F

A

djust the settings one by one, confirming
each time.
F

Sel

ect the " OK" tab in the screen and
confirm to exit the " Set date and time"
menu.
1
Instruments

26
Trip computer
Information displayed about the current journey
(range, fuel consumption, average speed, etc.).
Instrument Panel Screen
Monochrome screen C
Data displays
F Press the button at the end of the wiper stalk to display successively the different
trip computer data. The trip computer data
is as follows:
-


Range.
-

C
urrent fuel consumption.
-
D

istance travelled.
-
A

verage fuel consumption.
-
A

verage speed.
F

T
he next press then returns you to the
normal display.
Zero reset
F Hold the control down for more than two seconds to reset to zero the distance
travelled, the average fuel consumption and
the average speed.
Touch screen
Information is accessible from the
menu Driving / Vehicle .
Instruments

27
Display of information in the touch screen
Permanent display:
With CITROËN Connect Radio
F
Sel
ect the " Applications " menu, then " Tr i p
computer ".
With CITROËN Connect Nav
F

Sel
ect the " Applications " menu then the
" Vehicle apps " tab then "Trip computer ".
The trip computer information is displayed in
tabs.
F

P
ress one of the buttons to display the
desired tab.
Temporar y display in a specific window:
F

P
ress the end of the wiper control stalk
to access the information and display the
different tabs. The current information tab with:
-
Range.
-

C
urrent fuel consumption.
-

S
top & Start time counter.
The trip " 1" tab with:
-

A
verage speed for the first trip.
-
A

verage fuel consumption.
-
D

istance travelled.
The trip " 2" tab with:
-

A
verage speed for the second trip.
-
A

verage fuel consumption.
-
D

istance travelled.
Trip reset
F When the desired trip is displayed, press the reset button or on the end of the wiper
control stalk.
Tr i p s " 1" and " 2" are independent and are used
identically.
Tr i p " 1" allows daily calculations to be carried
out, for example, and trip " 2" allows monthly
calculations.
1
Instruments

29
Remote control key
System which permits central unlocking or
locking of the vehicle using the door lock or
from a distance.
It is also used to locate and start the vehicle, as
well as providing theft protection.
Unfolding / Folding the key
Complete unlocking
With the key
F Turn the key towards the front of the vehicle.
With the remote control
F Press this button to unlock the vehicle .
Unlocking is confirmed by rapid flashing
of the direction indicators for around two
seconds.
Selective unlocking
Complete unlocking is activated by default. It is possible to activate or deactivate
the selective unlocking with the touch
screen from the menu Driving /
Vehicle.
With the remote control
F To unlock the driver's door o n l y,
press this button once.
F

T
o unlock the other doors and
the boot , press this button again. Unlocking is confirmed by rapid flashing
of the direction indicators for around two
seconds.
Normal locking
With the key
F Turn the key in the driver's door lock,
towards the rear of the vehicle to lock it.
Check that the doors and boot are fully
closed.
With the remote control
F Press this button to lock the vehicle.
F

P

ress this button to unfold or fold the key.
The complete or selective boot
unlocking parameter is set via the
Personalisation-configuration

menu. F
P
ress this button for more than
one second to unlock the boot.
The boot opens slightly.
This action unlocks the vehicle first.
Unlocking and partial
opening of the boot
2
Access

30
Locking is confirmed by continuous lighting of
the direction indicators for approximately two
seconds.If one of the doors or the boot is still open,
the central locking does not work; the
vehicle locks, then immediately unlocks,
identifiable by the locks making a rebound
sound.
When the vehicle is locked, if it is
unlocked inadvertently, it will lock again
automatically after thirty seconds unless a
door or the boot is open.
Locating your vehicle
This function allows you to identify your vehicle
from a distance, particularly in poor light. Your
vehicle must be locked. F

P
ress the closed padlock button
on the remote control.
This will switch on the courtesy lights and the
direction indicators will flash for a few seconds.
Fault with the remote
control
In the event of a malfunction with the remote
control, you can no longer unlock, lock or
locate your vehicle.
F

F
irst of all, use the key in the door lock to
unlock or lock your vehicle.
F

T
hen reinitialise the remote control.
Reinitialisation
F Switch off the ignition and remove the key from the switch.
F

P
ress the closed padlock button for a few
seconds.
F

R
eturn the key to position 2 (ignition on ).
F

S
witch off the ignition and remove the key
from the switch.
The remote control is now fully operational
again.
Changing the battery
Battery type: CR2032 / 3 volts.
I f the battery is flat, you are informed
by lighting of this warning lamp in the
instrument panel, an audible signal
and a message in the screen. F

U
nclip the cover by inserting a small
screwdriver in the slot.
F
R
emove the cover.
F
R
emove the flat battery from its
compartment.
F
F
it the new battery into its compartment
observing the original fitting direction.
F
C
lip the cover onto the casing.
Access

31
Lost keys
Go to a CITROËN dealer with the vehicle's
registration document, your personal
identification documents and if possible the key
code label.
The CITROËN dealer will be able to look up the
key code and the transponder code required to
order a new key.Do not throw away the remote control
batteries, they contain metals which are
harmful to the environment.
Take them to an approved collection
point.
Anti-theft protection
Do not make any modifications to the electronic
engine immobiliser system; this could cause
malfunctions.
Remote control
The high frequency remote control is a sensitive
system; do not operate it while it is in your
pocket as there is a possibility that it may unlock
the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your
remote control out of range and out of sight of
your vehicle. You risk making it inoperative. It
will then be necessary to reinitialise it.
No remote control can operate when the key is
in the ignition switch, even when the ignition is
switched off, except for reinitialisation.
Locked vehicle
Driving with the doors locked may render
access by the emergency services to the
interior difficult in an emergency.
As a safety precaution, never leave children
alone in the vehicle, except for a very short
period.
In all cases, it is essential to remove the key
from the ignition switch when leaving the
vehicle. Second-hand vehicle
Have the pairing of all of the keys in your
possession checked by a CITROËN dealer, to
ensure that only your keys can be used to open
and start the vehicle.
2
Access

32
Alarm
System which protects and provides a deterrent
against theft and break-ins. It provides
perimeter protection and a self-protection
function.
Perimeter protection
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot, the bonnet, etc.Self-protection function
The system checks for the putting out of
ser vice of its components.
The alarm is triggered if the battery, the
central control or the siren wiring are put
out of ser vice or damaged.
For all work on the alarm system,
contact a CITROËN dealer or a qualified
workshop.
Locking the vehicle with
alarm
Activation
F Press the locking button on the remote control.
The alarm is activated: an indicator
lamp in the switch panel to the left of
the steering wheel flashes once per
second.
Deactivation
F Press the unlocking button on the remote control.
The alarm is deactivated: the
indicator lamp goes off.
Triggering of the alarm
F Turn the vehicle off and exit.
The perimeter protection is activated 5
seconds
after pressing the locking button on the remote
control.
If an access (door, boot, etc.) is not closed fully,
the vehicle will not be locked, but the alarm will
be activated. When the vehicle is unlocked using
the remote control, rapid flashing
of the indicator lamp informs you
that the alarm was triggered during
your absence. When the ignition
is switched on, this flashing stops
immediately.
This is indicated by sounding of the siren and
flashing of the direction indicators for thirty
seconds.
Locking the vehicle without
activating the alarm
F Lock the vehicle using the key.
Failure of the remote
control
To deactivate the monitoring functions:
F
U nlock the vehicle using the key.
F

O
pen the door; this sets off the alarm.
F

S
witch on the ignition; this stops the alarm.
Operating fault
When the ignition is switched on, continuous
illumination of the indicator lamp indicates a
fault with the system.
Have it checked by a CITROËN dealer or a
qualified workshop.
Access