battery CITROEN C-ELYSÉE 2023 Owner's Manual

94
In the event of a breakdown
It is not necessary to disconnect the
battery.
â–º

Switch the ignition off.
â–º


Switch off all electrical consumers (audio
system, lighting, wipers, etc.).


â–º Switch off charger B before connecting
the cables to the battery, so as to avoid any
dangerous sparks.
â–º

Ensure that the charger cables are in good
condition.
â–º


Lift the plastic cover on the (+) terminal, if the
vehicle has one.
â–º


Connect the cables of charger B

as follows:
•

the positive (+) red cable to the (+) terminal
of battery

A.
•

the negative (-) black cable to earth point C


on the vehicle.
â–º

At the end of the charging operation, switch
off charger B

before disconnecting the cables
from battery A.
If this label is present, use only a 12 V
charger to avoid causing irreversible
damage to the electrical components.
24V
12V
+
Disconnecting/reconnecting the
battery
In order to maintain an adequate state of
charge for starting the engine, we recommend
disconnecting the battery if the vehicle is to be
unused for an extended period.
Before disconnecting the battery:
â–º

Close all openings (doors, tailgate, windows).
â–º


Switch off all electricity-consuming devices
(audio system, wipers, lamps, etc.).
â–º


Switch off the ignition and wait for 4
minutes.
After accessing the battery, it is only necessary
to disconnect the (+) terminal.
Quick-release terminal clamp
Disconnecting the (+) terminal


â–º Depending on equipment, lift the plastic cover
on the (+) terminal.
â–º

Raise lever

A
fully to release clamp
B
.
â–º

Remove clamp

B
by lifting it off.
Reconnecting the (+) terminal

â–º Raise lever A fully.
â–º Refit open clamp B on the (+) terminal.

95
In the event of a breakdown
8â–º Push clamp B fully down.
â–º Lower lever A to lock clamp B.
â–º

Depending on equipment, lower the plastic
cover on the

(+) terminal.
Do not force the lever when pressing on
it, as if the clamp is not positioned
correctly, locking will then not be possible.
Start the procedure again.
The Stop & Start system may not be operational during the trip following the
first engine start.
In this case, the system will only be available
again after a continuous period with the
vehicle immobilised, the duration of which
depends on the exterior temperature and the
state of charge of the battery (up to about 8
hours).
Following reconnection
After reconnecting the battery, turn on the
ignition and wait 1 minute before starting the
engine, to enable the electronic systems to
initialise.
If minor problems nevertheless persist following
this operation, contact a CITROËN dealer or a
qualified workshop.
Referring to the relevant section, reinitialise
certain equipment:
–

Remote control key
.
–

Electric windows.
–


Date and time.
–


Preset radio stations.
Towing the vehicle
General recommendations
Observe the legislation in force in the
country where you are driving.
Check that the towing vehicle is heavier than
the towed vehicle.
The driver must remain at the wheel of the
towed vehicle and must have a valid driving
licence.
When towing a vehicle with all four wheels on
the ground, always use an approved towbar;
ropes and straps are prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no longer braking and steering
assistance.
A professional recovery service must
be called in the following cases:
–

broken down on a motorway or main road;
–


not possible to put the gearbox into neutral,
unlock the steering, or release the parking
brake;
–


not possible to tow a vehicle with an
automatic gearbox, with the engine running;
–


towing with only two wheels on the ground;
–


four-wheel drive vehicle;
–


no approved towbar available.
Towing constraints
Type of vehicle
(engine/gearbox) Front wheels on the
ground Rear wheels on the
ground Flatbed
4 wheels on the ground
with towbar
Internal combustion/Manual

102
Bluetooth® audio system
Bluetooth® audio system

As a safety measure and because it requires sustained attention by the driver,
the pairing of a Bluetooth mobile telephone
with the Bluetooth hands-free system of your
audio system must be done with the vehicle
stationary and the ignition on.
Your audio system is coded in such a way that it will only operate in your
vehicle.
All work on the system must be carried out
exclusively by a dealer or qualified workshop,
to avoid any risk of electrocution, fire or
mechanical faults.
To avoid discharging the battery, the audio system may switch off after a few
minutes if the engine is not running.
First steps
Volume adjustment.
On / Off.
TA (Traffic Announcement) function On /
Off.
Long press: access to type of information.
Select the source:
Radio, CD, AUX, USB, Streaming.
Accept an incoming call.
Manual step by step up / down frequency
search for radio stations.
Select previous
/ next MP3 track.
Select previous
/ next folder / genre / artist /
playlist of the USB device.
Scroll in a list.
Access to the main menu.
Automatic search for a lower / higher
radio frequency .
Select previous
/ next CD, USB, streaming track.
Scroll in a list.
Select a preset radio station.
Long press: memorise a radio station.
Cancel the current operation.
Go up one level (menu or folder).
Confirm or display contextual menu.
Display the list of stations received, the
CD
/ MP3 tracks or folders.
Long press: manage the classification of MP3
/
WMA files
update the list of stations received.
Adjust audio settings: sound ambience, treble, bass, loudness, distribution, left / right balance, front
/ rear balance, automatic
volume.
Select the screen display mode, between:
Full screen: Audio (or telephone if call in
progress)
/
Windowed screen: Audio (or telephone if call in
progress)
- Time or Trip computer.
Long press: black screen (DARK).
Select AM / FM wavebands.
Steering mounted controls
Radio: automatic search for lower
frequency.
CD /MP3 / USB: selection of the previous track.
CD / USB: press and hold: fast back.
Skip in the list.
Change the audio source.
Confirm a selection.
Call/end call on the telephone.
Press for more than 2 seconds: access
telephone main menu.
Radio: automatic search for a higher
frequency.
CD / MP3 / USB: select the next track.
CD / USB: press and hold: fast forward.
Skip in the list.
Increase volume.
Decrease volume.

111
Bluetooth® audio system
10– Check that the CD is inserted in the player the
right way up.
–

Check the condition of the CD: the CD cannot
be played if it is too badly damaged.
–


Check the content in the case of a recorded
CD: consult the advice in the "Audio" section.
–


The audio system’
s CD player does not read
DVDs.
–

Because of low quality
, certain burned CDs
will not be read by the audio system.
The CD sound is of poor quality.
1.The CD used is scratched or of poor quality.
Insert good quality CDs and store them in
suitable conditions.
2.The audio settings (bass, treble, ambience) are
unsuitable.
Return bass and treble settings to 0, without
selecting an ambience.
I am unable to connect my Bluetooth
telephone.
1.It is possible that Bluetooth is switched off on
the telephone or that the telephone has been
made not visible.
–

Check that your telephone has Bluetooth
switched on.
–


Check in the telephone settings that it is
"visible to all".
2.

The Bluetooth telephone is not compatible with
the system.
To check the compatibility of your telephone
(services), visit the Manufacturer's website in
your country.
The Bluetooth connection is cut.The battery of the peripheral may not be
sufficiently charged.
Charge the battery of the peripheral device.
The "USB peripheral error" or "Peripheral not
recognised" message appears on the screen.
The USB memory stick is not recognised. The
memory stick could be corrupt.
Reformat the memory stick (FAT 32).
A telephone connects automatically,
disconnecting another telephone.
Automatic connection overrides manual
connection.
Modify the telephone settings to remove
automatic connection.
The Apple
® player is not recognised when
connecting to the USB port.
The Apple
® player is of a generation that is not
compatible with a USB connection.
Connect the Apple
® player to the AUX Jack
socket using a suitable cable (not supplied).
The hard disk or peripheral is not recognised
when connecting to the USB socket.
Some hard disks and devices need a power
supply greater than is provided by the audio
system.
Connect the peripheral to the 230 V socket, the
12V socket or an external power supply.
Ensure that the device does not transmit
a voltage greater than 5 V (risk of
destruction of the system).
When streaming, the sound cuts
momentarily. Some telephones prioritise connection of the
"hands-free" profile.
Delete the "hands-free" connection profile to
improve streaming.
In "Random all" play, not all of the tracks are
played.
In "Random all" play, the system can only take
into account up to 999 tracks.
With the engine off, the audio system
switches off after a few minutes of use.
When the engine is switched off, the audio
system operating time depends on the battery
charge.
The switch-off is normal: the audio system
switches to economy mode and switches off to
prevent discharging the vehicle's battery.
Start the vehicle’s engine to increase the battery
charge.
The message "the audio system is
overheated" appears on the display.
In order to protect the installation if the
surrounding temperature is too high, the audio
system switches to an automatic thermal
protection mode leading to a reduction of the
volume or stopping of the playing of the CD.
Switch the audio system off for a few minutes to
allow the system to cool.

124
CITROËN Connect Radio
The connected device does not automatically
launch playback.
â–º
Start playback from the device.
T

rack names and playing times are not
displayed on the audio streaming screen.
The Bluetooth profile does not allow the transfer
of this information.
Telephone
I cannot connect my Bluetooth telephone.
The telephone's Bluetooth function may be
switched off or the device may not be visible.
â–º

Check that the telephone has Bluetooth
switched on.
â–º


Check in the telephone settings that it is
"visible to all".
The Bluetooth telephone is not compatible with
the system.
â–º


Check the compatibility of the telephone on
the Brand's website (services).
Android

Auto and/or CarPlay do not work.
Android Auto and CarPlay may not activate if the
USB cables are of poor quality.
â–º

Use genuine USB cables to ensure
compatibility

.
Android Auto and/or CarPlay do not work.
Android Auto and CarPlay are not available in all
countries.
â–º

Check the Google
Android Auto or Apple
website to see which countries are supported.
The volume of the telephone connected in
Bluetooth mode is inaudible. The volume depends on both the system and the
telephone.
â–º

Increase the volume of the audio system, to
maximum if required, and increase the volume of
the telephone if necessary
.
Ambient noise affects the quality of the
telephone call.
â–º
Reduce ambient noise (close windows, turn
down ventilation, slow down, etc.).
The contacts are not listed in alphabetical
order
.
Some telephones offer display options.
Depending on the settings chosen, contacts can
be transferred in a specific order.
â–º

Modify the telephone directory display
settings.
Settings
When the treble and bass settings are
changed, the ambience is deselected.
When the ambience is changed, the treble
and bass settings are reset.
Selecting an ambience imposes the treble and
bass settings, and vice versa.
â–º

Modify the treble and bass or ambience
settings to obtain the desired musical ambience.
When the balance settings are changed, the
distribution is deselected.
When the distribution setting is changed, the
balance settings are deselected.
Selecting a distribution setting imposes the
balance settings, and vice versa. â–º


Modify the balance setting or the distribution
setting to obtain the desired sound quality
.
There is a difference in sound quality
between audio sources.
To allow for optimal listening quality, the sound
settings can be tailored to different audio
sources, which can generate audible differences
when changing source.
â–º
Check that the sound settings are appropriate
to the sources listened to.
Adjust the sound
functions to the middle position.
When the engine is off, the system switches
off after several minutes of use.
When the engine is switched off, the system's
operating time depends on the state of charge of
the battery.
The switch-off is normal: the system
automatically goes into energy economy mode
and switches off to maintain an adequate charge
in the battery.
â–º

Start the vehicle’
s engine to increase the
charge of the battery.

148
CITROËN Connect Nav
Settings
When the treble and bass settings are
changed, the ambience is deselected.
When the ambience is changed, the treble
and bass settings are reset.
Selecting an ambience imposes the treble and
bass settings, and vice versa.
â–º
Modify the treble and bass or ambience
settings to obtain the desired musical ambience.
When the balance settings are changed, the
distribution is deselected.
When the distribution setting is changed, the
balance settings are deselected.
Selecting a distribution setting imposes the
balance settings, and vice versa.
â–º


Modify the balance setting or the distribution
setting to obtain the desired sound quality

.
There is a difference in sound quality
between audio sources.
To allow for optimal listening quality, the sound
settings can be tailored to different audio
sources, which can generate audible differences
when changing source.
â–º

Check that the sound settings are appropriate
to the sources listened to. W

e recommend
setting the sound functions (Bass:, Treble:,
Balance) to the middle position, setting the
musical ambience to "None", setting loudness
correction to "Active" in USB mode and "Inactive"
in Radio mode.
â–º

In all cases, after applying sound settings,
adjust the volume level on the portable device (to a high level) first.

Then adjust the volume level
on the audio system.
When the engine is off, the system switches
off after several minutes of use.
When the engine is switched off, the system's
operating time depends on the state of charge of
the battery.
The switch-off is normal: the system
automatically goes into energy economy mode
and switches off to maintain an adequate charge
in the battery.
â–º

Start the vehicle’
s engine to increase the
charge of the battery.
The date and time cannot be set.
Setting of the date and time is only available
if the synchronisation with the satellites is
deactivated.
â–º

Settings menu / Options /
Time-Date setting.
Select the "Time" tab and deactivate the "GPS
synchronisation" (UTC).

149
Vehicle data recording and privacy
13Vehicle data recording
and privacy
Electronic control units are installed in your
vehicle. These control units process data
received from the vehicle's sensors, for example,
or data they generate themselves or exchange
with each other. Some of these control units are
required for the correct operation of your vehicle,
some others assist you while driving (driving or
manoeuvring aids), while others provide comfort
or infotainment functions.
The following contains general information about
how data is processed within the vehicle.
You will find additional information about the
specific data which is downloaded, stored
and transmitted to third parties and what it is
used for in your vehicle under the keyword
"Data protection". This information is directly
associated with the references for the functions
in question contained in the corresponding
vehicle handbook, or in the general terms and
conditions of sale.
This information is also available online.
Vehicle operating data
The control units process the data used for the
operation of the vehicle.
This data includes, for example:
–
Information about the state of the vehicle
(e.g.

speed, travel time, lateral acceleration,
wheel rotation rate, fastened seat belts display). –

Environmental conditions (e.g.
temperature,
rain sensor, distance sensor).
As a general rule, this data is temporary, is
not stored for longer than one operating cycle
and is only used within the vehicle itself. The
control units often record this data (including the
vehicle's key). This function allows either the
temporary or permanent storage of information
about the state of the vehicle, stresses on
components, servicing requirements, as well as
events and technical errors.
Depending on the vehicle's equipment level, the
data stored is as follows:
–
Operating state of system components
(e.g.
filling level, tyre pressures, battery charge
status).
–
Faults and malfunctions in important system
components (e.g.
lamps, brakes).
–
System reactions in specific driving situations
(e.g.
deployment of an airbag, triggering of
stability control and braking systems).
–
Information about events which have
damaged the vehicle.
–

For electric and rechargeable hybrid vehicles,
the traction battery charge level and the
estimated driving range.
In particular circumstances (e.g.
if the vehicle
has detected a malfunction), it may be necessary
to record data which would otherwise simply not
be stored.
When taking your vehicle in for servicing
(e.g.
repairs, maintenance), the stored operating
data may be read along with the vehicle's identification number and used if necessary.
The personnel working for the servicing network
(e.g.
garages, manufacturers) or third parties
(e.g. roadside assistance agents) may read
the vehicle's data. This also applies to work
carried out under warranty and quality assurance
measures.
This data is generally read via the OBD
(On-Board Diagnostics) port fitted by law to
the vehicle. It is used to report on the technical
state of the vehicle or its components and
facilitates the diagnosis of malfunctions, in
compliance with warranty obligations and for
quality improvement. This data, in particular the
information relating to stress on components,
technical events, operator errors and other
malfunctions, is sent to the Manufacturer, if
necessary, along with the vehicle's identification
number. The Manufacturer's liability may also be
engaged. The Manufacturer may also use the
operating data taken from the vehicle for product
recalls. This data may also be used to check the
customer's warranty and any claims made under
warranty.
Any malfunctions stored in the vehicle may be
reset by an after-sales service company during
servicing or repair work, or at your request.

152
Alphabetical index
A
ABS 38
Accessories
37
AdBlue®

70
AdBlue® tank

72
Additive, Diesel

78–79
Adjusting headlamps

35
Adjusting head restraints

23
Adjusting seat

23–24
Adjusting the date

14, 123, 145
Adjusting the headlamp beam height

35
Adjusting the height and reach
of the steering wheel

25
Adjusting the time

14, 122, 145
Advice on care and maintenance

81
Advice on driving

6, 51–52
Airbags

41–43, 45
Airbags, curtain

42
Airbags, front

42–43, 45
Airbags, lateral

42–43
Air conditioning

26
Air conditioning, electronic
(with display screen)

28–29
Air conditioning, manual
(without display screen)

27
Air vents

26
Alarm

21–22
Anti-lock braking system (ABS)

38
Antitheft / Immobiliser

18
Armrest, front

30–31
Ashtray, portable

30
Assistance, emergency braking 38
Audio streaming
(Bluetooth)

106–107, 118, 139
B
Battery 92
Battery, 12 V
73, 79, 92–94
Battery, charging

92–93
Battery, remote control

19
Blanking screen (snow shield)

74–75
BlueHDi

79, 83
Bluetooth (hands-free)

106, 120, 140–141
Bluetooth (telephone)

120–121, 140–142
Bodywork

81
Bonnet

76
Boot

20–21
Boot (opening)

17
Brake discs

80
Brake lamps

90
Brakes

80
Braking assistance system

38
Brightness

122
Bulbs (changing)

87–88, 90
C
Cable, audio 139
Cable, Jack
139
Capacity, fuel tank

69
Care of the bodywork 81
CD
104, 139
CD, MP3

104, 139
Central locking

18
Changing a bulb

87–88, 90
Changing a fuse

91
Changing a wheel

84
Changing a wiper blade

35–36
Changing the remote control battery

19
Changing to free-wheeling

80
Checking the levels

77–78
Checks

76–77, 79–80
Checks, routine

79–80
Child lock

46, 49–50
Children

40, 46–49
Children (safety)

50
Child seats

40, 43–46
Child seats, conventional

45
Child seats, ISOFIX

47–49
Cigar lighter

31
Cleaning (advice)

81–82
Clock

14
Closing the boot

20–21
Closing the doors

20
Connection, Apple CarPlay

119, 134
Connection,
Bluetooth

120–121, 136–137, 140–142
Connection, MirrorLink

119, 135
Connection, Wi-Fi network

137
Container, AdBlue®

71–72
Control, emergency boot release

21
Control, emergency door

19

155
Alphabetical index
Opening the bonnet 76
Opening the boot
17, 20–21
Opening the doors

17, 20
P
Pads, brake 80
Paint
81, 100
Paint colour code

100
Parking brake

54, 80
Parking sensors, audible and visual

66
Plates, identification

100
Player, Apple®

118, 140
Player, MP3 CD

104, 139
Player, USB

104, 117, 139
Port, USB

31, 104–105, 117–118, 139
Pressures, tyres

80, 101
Pre-tensioning (seat belts)

40
Priming pump

83
Priming the fuel system

83
Profiles

121, 144
Protecting children

42–49
Puncture

84
R
Radio 103, 115–116, 137–139
Radio, digital (Digital Audio
Broadcasting - DAB)

117, 138–139
Range, AdBlue®

79
RDS 116, 138
Reading lamps
32
Rear bench seat

24
Rear screen (demisting)

29–30
Recharging the battery

92–93
Recorder, trip distance

13
Reduction of electrical load (mode)

74
Regeneration of the particle filter

79
Reinitialising the remote control

20
Reinitialising the under-inflation
detection system

61
Reminder, key in ignition

54
Reminder, lighting on

33
Remote control

17–19, 52
Removing a wheel

85–86
Replacing bulbs

87–88, 90
Replacing fuses

91
Replacing the air filter

79
Replacing the oil filter

79
Replacing the passenger
compartment filter

79
Reservoir, screenwash

78
Resetting the trip recorder

13
Reversing camera

62, 67
Reversing lamps

90
Roof bars

75
Running out of fuel (Diesel)

83
S
Safety, children 42–45, 47–48
Saturation of the particle filter (Diesel) 79
Screen, cold climate
74
Screen menu map

119
Screen, multifunction (with audio system)

103
Screens, very cold conditions

75
Screenwash

35
Screenwash, front

35
SCR (Selective Catalytic Reduction)

70
Seat belts

39–40, 45
Seat belts, rear

40
Seats, front

23
Seats, rear

24, 44
Sensors (warnings)

62
Serial number, vehicle

100
Servicing

11, 79
Settings, system

122, 144
Shield, snow

74
Sidelamps

34, 88–90
Side repeater (turn signal)

90
Snow chains

61, 73
Snow screen

74
Socket, 12 V accessory

31
Socket, auxiliary

105, 117, 139
Socket, Jack

31, 105, 139
Sockets, audio

31, 105
Speed limiter

63–64
Speedometer

63
Stability control (ESC)

38
Starting a Diesel engine

69
Starting the vehicle

53–54, 57
Starting using another battery

93
Station, radio

103, 115–116, 137–138