turn signal Citroen C ZERO 2010.5 1.G Owner's Manual

.Familiarisation
15
Driving safely
P.
Parking.
Press the brake pedal to come out of this
position.R.Reverse.N. Neutral. D.Drive (forward).


Drive selector
54- Check that the drive selector is in position
P
. PP- Inser t the key in the ignition switch.
- Turn the key to position 4 (START).- Hold it in this position for a few seconds,until the " READY" lamp comes on,
accompanied by an audible signal.
- Release the key.
The switch returns automatically to
position
3 (ON) .
Starting the motor
52



- Stop the vehicle.

- Keep your foot on the brake pedal.

- Put the drive selector in position P
. P

- Apply the parking brake.

- Turn the key anti-clockwise to the LOCKposition.


Stopping the motor
52

Monitoring
20
Operation indicator lamps
If one of the following indicator lamps comes on in the instrument panel, this confirms that the corresponding system has come into operation.

Warning/indicator lampStateCauseAction/Observations



Left-hand direction indicatorFlashing with audible signal. The lighting stalk is pushed down.


Right-handdirection indicatorFlashing with audible signal. The lighting stalk is pushed up.


Hazard warning lampsFlashing with audible signal. The hazard warning lamps switch,located on the dashboard, has been
operated. The left-hand and ri
ght-hand direction indicators and
their associated indicator lamps flash simultaneously.


Sidelampsand/or dipped beamheadlamps
On fixed. The sidelamps and/or dipped beamheadlamps are on.



Front foglampsOn fixed. The front foglamps are switched on. Turn the ring on the stalk rear wards twice to switch off
the front foglamps.


Rear foglampOn fixed. The rear foglamp is switched on. Turn the ring on the stalk rear wards to switch off the
rear foglamp.


Main beam headlampsOn fixed. The lighting stalk is pulled towardsyou. Pull the stalk to return to dipped beam headlamps.

i
!
Driving
52










Starting - stopping the vehicle
- Position 1: LOCK
The steering is locked.
- Position 2: ACCThe ancillaries (radio, 12 V socket...)can be used.
- Position 3: ONIgnition on.
- Position 4: START"Ready" lamp on.
Motor ready to drive the vehicle.
Ignition switch
) Inser t the key in the ignition switch.
)
Turn the key to position 4 (START).


Starting
Stopping
)Immobilise the vehicle.
)Place the drive selector in position P.P)Turn the key to position 1 (LOCK).)Remove the key from the ignition switch.)Hold it in this position for a few seconds until the "READY" lamp comes on accompanied by an
audible signal.
) Release the key.
The key returns automaticallyto position 3 (ON).
Key in ignition
If the key has been left in the ignition, an
audible signal is heard on opening the driver's door.

Do not attach any heavy objects to the key as this could weigh down on it whenin the ignition switch and cause a fault.

If you use the ancillaries for a prolonged period (with the key in the ACCposition), you risk discharging theancillaries battery. Star ting your vehiclewill then no longer be possible.Be aware .

5
i !
Visibility
57





Front and rear foglamps
Foglamps selection ring.
The foglamps operate with the sidelamps and
dipped and main beam headlamps. Front and rear
foglamps. In good or rainy weather, both dayand night, the front foglamps and the rear foglamp is prohibited. In these situations, the power of its beam may
dazzle other drivers. Do not forget to switch off the front foglamps and the rear foglamp whenthey are no longer necessary.


Lighting on reminder
There is an audible signal when the driver's door is opened, to warnthe driver if the vehicle lighting is on, with the ignition off. Switching off the lighting stops theaudible signal.
)
To switch on the front foglamps, turn
the ring for wards once. ) To switch on the rear foglamp, turn the ring
forwards twice.) To switch off the rear foglamp, turn the ring rearwards twice.)
To switch off the front foglamps, turn
the ring rearwards once.
The ring returns to its initial position
automatically.
The rear foglamp is switched off automatically when you switch off the sidelamps, or
the dipped or main beam headlamps.

i
i
i
Visibility
58
Daytime running lamps
Special daytime lighting so that the vehicle can
be seen more easily. The daytime running lamps come on automatically when star ting the motor, if no
other lighting is on.
They cannot be deactivated. With the main li
ghting control ring in the AUTO
position, the sidelamps and dipped beam
headlamps come on automaticall
y, without anyaction by the driver, when a low level of ambientlight is detected.
When the light returns to a sufficient level or the
wipers are switched off, the lighting is switched
off automatically.
The sensor is located at the base of the
windscreen.
Automatic illumination of headlamps
Automatic lighting off
When the lighting stalk is in the "dipped or mainbeam headlamps" position, if the ignition switch
is in the "LOCK" or "ACC" position or if thekey has been removed, the lighting switches
off automatically when the driver's door isopened .
The driver is is aler ted by an audible signal. The initial setting is position "0".









Headlamp
adjustment

To avoid causing a nuisance to other road
users, the height of the halogen headlampsshould be adjusted according to the load in the
vehicle. 0. Driver only or driver + 1 front passenger.
1 or 2.
4 people (including the driver). 3.4 people (including the driver) + maximumauthorised load.4.
Driver + maximum authorised load.

Even though these lamps are located inthe same lamp unit as the front foglamp, the operate with a specific bulb.
Their use is covered by road vehiclelighting regulations.
In foggy weather or in snow, thesunshine sensor may detect sufficient light. The lighting will not come on automatically. Do not cover the sunshine sensor, theassociated functions will no longer becontrolled.

7
Safety
73
Seat belts


Front seat belts
Fastening
)
Pull the strap, then inser t the tongue inthe buckle A.)
Check that the seat belt is fastened correctly by pulling the strap.



Front seat belt not fastened/
unfastened warning lamp

If the driver does not fasten their seat
belt within one minute after switching on
the ignition, the warning lamp flashes
accompanied by an intermittent audible signal.
After about 90 seconds, the warning lamp, the
audible signal and the display stop, and then
return until the driver fastens their seat belt.
If the seat belt is unfastened while the vehicle is moving
, you are warned by the same alerts.

Th
e front seat belts are fitted with a
pretensioning and force limiting system.
This system improves safety in the frontseats in the event of a front or side impact.
Depending on the severity of the impact,
the pretensioning system instantly tightens
the seat belts against the body of the
occupants.

The pretensioning seat belts are active when
the ignition is on.
The force limiter reduces the pressure of
the seat belt on the chest of the occupant,so improving their protection.

Unfastening
)
Press the red button on the buckle A
.

When the ignition is switched on, this
warning lamp comes on accompanied
by an audible signal for a few secondsif the driver and/or passenger has notfastened their seat belt.