lock CITROEN C-ZERO DAG 2017 Handbook (in English)

86
C-Zero_en_Chap05_securite_ed01-2016
Child lock
Mechanical system to prevent opening of the
rear doors using their interior controls.
The control is located on the edge of each rear
d o o r.
Child lock on
F Lower the control A to position 1.
Child lock off
F Raise the control A to position 2.
Safety

88
C-Zero_en_Chap06_conduite_ed01-2016
Starting - stopping the vehicle
- Position 1: LOCK The steering is locked.
-

P
osition 2: ACC
T

he ancillaries (radio, 12 V socket, etc.)
can be used.
-

P
osition 3: ON
I

gnition on.
-

P
osition 4: S TA R T
"

Ready" lamp on.
M

otor ready to drive the vehicle.
Ignition switch
F Check that the drive selector is in position P.
F

I
nsert the key in the ignition switch.
F

T
urn the key to position 4 (S TA R T ) .
StartingStopping
F Stop the vehicle.
F
K eep your foot on the brake pedal.
F

P
lace the drive selector in position P .
F

A
pply the parking brake.
F

T
urn the key to position 1 (LOCK) .
F

R
emove the key from the ignition switch.
F

H

old it in this position for a few
seconds until the " RE ADY " lamp
comes on accompanied by an
audible signal.
F

R

elease the key.
T

he key returns automatically to
position


3


(ON) . Do not attach any heavy objects to the
key as this could weigh down on it when
in the ignition switch and cause a fault.
If you use the ancillaries for a prolonged
period (with the key in the ACC
position), you risk discharging the 12 V
battery. Starting your vehicle will then
no longer be possible. Be aware.
Driving

97
Charging the main battery
Normal charging
During charging, if you
wear a pacemaker or other
electrical medical device, you F
A pply the parking brake and put the drive
selector in position P .
F

S
witch off all electrical consumers and turn
the ignition switch to the "LOCK" position.
In most European countries, CITROËN
has established a partnership with a
specialist company that can check and
bring your electrical installation up to
standard. For more information, contact
a CITROËN dealer. In the event of damage to or
deterioration of the charging cable or
control unit, do not use it. Contact a
CITROËN dealer if in doubt or for a
replacement.You must always use only a genuine
CITROËN charging cable.
Before connecting, check that the
electrical installation you want to use
meets standards* and is compatible
with the rating of your charging unit.
If in doubt, call upon a professional
installer.
There are sockets available that are
specially designed for charging electric
vehicles.
For sockets dedicated to charging an
electric vehicle, refer to the installation
instructions for the socket.
In all cases, it is recommended that
that you first have an initial check
and then regular checks
carried out
on your installation by a qualified
electrician.
* For example, in France the standard is NF C 15 -100. must not stay inside the vehicle or near
the vehicle, charging cable, charging
unit or charging point, even for a short
time.
It is also important that you take advice
from your doctor on the precautions to
take and observe.
There are two types of charging you can use:
normal or fast.
Normal charging should be favoured; it is done
from a domestic mains power point.
Fast charging is done at a compatible fast
charging station.
7
Practical information

104
Check the compatibility of the charging
station and its charging cable with your
vehicle.F

P
ress latch 4 to open the socket cover.
F

E
nsure that there is no foreign body on the
vehicle's charging socket.
Fast charging*
F Apply the parking brake and put the drive selector in position P .
F

S
witch off all electrical consumers and turn
the ignition switch to the "LOCK" position.
F

P
ull lever 3 , located alongside the driver's
seat, door side, to open the access flap for
the fast charging socket (left-hand side of
the vehicle). Do not touch the metal end of the fast
charging socket or of the charging
cable.
Risk of electrocution and/or faults.
F
C
onnect the charging cable of the charging
station to the vehicle following the
instructions on use of the station.
If you wear a pacemaker
or other electrical medical
device, you must not use fast
charging.
Avoid going near a fast charging point.
However, should this occur, leave the area as
quickly as possible.
If necessary, ask someone else to charge
your vehicle.
* Depending on equipment.
Practical information

115
C-Zero_en_Chap08_en-cas-de-panne_ed01-2016
Charging the battery using
a battery charger
F Start the other vehicle and wait a few m inutes.
F

T
urn the ignition key on your vehicle, until
the "Ready" lamp comes on.
F

D
isconnect the cables in the reverse order.
F

R
efit the battery protective cover and
tighten the fixing screw.
If the "Ready" lamp does not come on, proceed
as follows:
F

L
eave the cables connected.
F

R
eturn the ignition switch on your vehicle
to the " LOCK" position.
F

P
ut the main battery on charge, following
the procedure for normal charging.
F

W
hen the charging warning lamp in
the instrument panel comes on fixed,
disconnect the cables.
F

L
eave the battery on charge for at least
one hour.
F

T
urn the ignition key on your vehicle, until
the "Ready" lamp comes on.
If the problem persists, contact a
CITROËN
dealer or a qualified workshop. F
R emove the protective cover from the
battery.
Ensure that the electrolyte is not frozen.
Check the electrolyte level and top up
with distilled water if necessary.
For more information on Checking
levels , refer to the corresponding
section. F

S
lacken the nut 1 and lift off the
retaining
ba

r.
8
In the event of a breakdown

117
C-Zero_en_Chap08_en-cas-de-panne_ed01-2016
This kit is installed in the storage box, under the
rear seat, right-hand side.
You must therefore remove the rear seat
cushion for access to the kit. Complete system consisting of a compressor
and a sealant cartridge which permits the
temporary repair of a tyre so that you can
drive to the nearest garage.
It is designed to repair most punctures which
could affect the tyre, located on the tyre tread
or shoulder.
Temporary puncture repair kit
Access to the kit
Removing the rear seat cushion
F Pull the controls A for wards to release the two rear seat cushion locks.
Removing the metal cover
F Remove the four "butter fly" screws.
F R emove the metal cover.
You now have access to the repair kit.
F

L

ift the front of the cushion and tip it
upwards to remove it.
8
In the event of a breakdown

118
C-Zero_en_Chap08_en-cas-de-panne_ed01-2016
1. 12 V compressor with integral pressure gauge, to measure and adjust the tyre
pressure.
Composition of the kit
2. Sealant cartridge for the temporary repair of a tyre.
3.
I

njection pipe.
4.
S

uction pipe, to remove the sealant product
if necessary.
5.
S

achet containing a replacement valve
core, a tool for removing/refitting the valve
core and a speed restriction sticker.
The speed restriction sticker must
be affixed to the vehicle's steering
wheel to
remind you that a wheel is in
temporary use.
Do not exceed a speed of 50 mph
(80
km/h) when driving with a tyre
repaired using this type of kit.
Refitting the rear seat cushion
F Put the metal cover back into place.
F R efit the four "butter fly" screws.
F

I
nsert the metal hooks into the seat
backrest.
F

F
old the seat cushion down and press to
secure the two locks.
F

C
heck that the seat cushion is locked
securely.
When refitting the cushion, take care
not to trap the seat belt buckles.
In the event of a breakdown

121
C-Zero_en_Chap08_en-cas-de-panne_ed01-2016
Spare wheel
Tools required
- A jack: for lifting the vehicle.
- A w heelbrace: for removing and refitting
the wheel bolts.
-

A h
andle: for operating the jack.
These tools are not supplied with your vehicle.Parking the vehicle
Immobilise the vehicle where it does not
block traffic: the ground must be level,
stable and not slippery.
Apply the parking brake, switch off the
ignition and put the drive selector in
position P to lock the wheels.
If necessary, place a chock under the
wheel diagonally opposite the wheel to
be changed.
You must ensure that the occupants get
out of the vehicle and wait where they
are safe.
Never go underneath a vehicle raised
using a jack; use an axle stand.
Wheel with wheel trim
When removing the wheel , first
remove the wheel trim using the
wheelbrace, by pulling at the valve hole.
When refitting the wheel , refit the
wheel trim starting by aligning the valve
hole with the valve, and then press on
the edge of the trim with the palm of
your hand.
8
In the event of a breakdown

130
C-Zero_en_Chap08_en-cas-de-panne_ed01-2016
Changing dipped beam headlamp
bulbs
F Turn the bulb holder to the left and pull it out.
F

R
emove the bulb by pressing on the tongue.
F

C
hange the bulb.
To refit, carry out these operations in reverse
o r d e r.
Changing front foglamp bulbs /
d aytime running lamp bulbs
F Put the front wheels onto full lock,
to facilitate access.
F

R
emove the clips securing the protective
covers on the bulb holders.
F

M
ove the cover aside. F
T urn the bulb holder (A for the front fog
lamp, B for the daytime running lamp) to
the left and pull it out.
F

P
ull the bulb out and change it.
To reassemble, carry out these operations in
reverse order.
In the event of a breakdown

134
C-Zero_en_Chap08_en-cas-de-panne_ed01-2016
Changing a fuse
The extraction tweezer is fitted to the back of
the fusebox cover in the dashboard (left-hand
side).
To gain access to it:
F
U
nclip the cover and remove it completely
by pulling it towards you.
F

R
emove the tweezer.
Access to tools
Before changing a fuse, the cause of the failure
must be identified and rectified.
F
C
heck that the ignition switch is in
the
"LOCK " position.
F

I
dentify the faulty fuse by checking the
condition of its filament.
Changing a fuse
Good Failed
F

U

se the special tweezer to extract the fuse
from its location.
F

A

lways replace the faulty fuse with a fuse
of the same rating.
F

C

heck that the number etched on the box,
the rating etched on the top and the tables
below all agree. CITROËN will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying the malfunctions
resulting from the installation of
accessories not supplied and not
recommended by CITROËN and
not installed in accordance with its
instructions, in particular when the
consumption of all of the additional
equipment connected exceeds
10
mil

liamperes.
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories in your
vehicle, contact a CITROËN dealer or a
qualified workshop.
In the event of a breakdown