wheel CITROEN C1 2010 User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010, Model line: C1, Model: CITROEN C1 2010Pages: 97, PDF Size: 3.96 MB
Page 76 of 97
9
72
PRACTICAL INFORMATION
Parking the vehicle
As far as possible, immobilise
the vehicle on level, stable, non-
slippery ground.
Apply the parking brake, switch
o f f t h e i g n i t i o n a n d e n g a g e fi r s t
gear or reverse for the manual
gearbox, position N for the
"SensoDrive" gearbox. Tools
The following tools are installed in a
carrier, located in the centre of the
spare wheel:
1. Wheelbrace
2. Jack with handle
3. Removable towing eye
Access to the spare wheel and
the jack in the boot
Remove the carpet then the
plastic cover using the handle. Tyre pressures
These are indicated on the label po-
sitioned on the inner pillar of the left
d o o r , s e e " I d e n t i fi c a t i o n m a r k i n g s " .
CHANGING A WHEEL
If necessary, chock the wheel
diagonally opposite the wheel to
be changed.
It is imperative that you ensure
that the occupants get out of
the vehicle and wait in a safe
location.
Page 77 of 97
9
73
PRACTICAL INFORMATION R e fi t t i n g t h e w h e e l
1. Position the wheel.
2. Screw in the bolts fully by hand.
Removing the wheel
1. Remove the trim.
2. Slacken the wheel bolts using the
wheelbrace 1 .
3. Place the jack 2 in contact
with one of the four locations A
provided on the underbody, the
one closest to the wheel to be
changed.
4. Extend the jack 2 until its base is
in contact with the ground. Ensure
that the centreline of the jack base
is directly below the location A
used.
5. Lift the vehicle.
6. Remove the bolts and detach the
wheel.
3. Pre-tighten the bolts * using the
wheelbrace 1 .
* I f y o u r v e h i c l e i s fi t t e d w i t h a l l o y w h e e l s , w h e n t i g h t e n i n g t h e b o l t s i t i s normal
to notice that the washers do not come into contact with t he spare wheel. It is
s t i l l fi x e d s e c u r e l y .
Page 78 of 97
9
74
PRACTICAL INFORMATION
CHANGING A BULB
1. Sidelamps (W5 W)
Turn the bulb holder A one quarter
of a turn and remove it.
Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)
Turn the bulb holder B one quarter
of a turn and remove it.
Turn the bulb one quarter of a
turn.
Remove the bulb and change it.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s , c o n -
t a c t a C I T R O Ë N d e a l e r o r a q u a l i fi e d
workshop.
In certain climatic conditions
(low temperatures, humidity),
the presence of condensa-
tion on the internal face of
the headlamps is normal ; it disap-
pears a few minutes after the lighting
is switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
4. Fold the jack 2 and detach it.
5. Tighten the wheel bolts using the
wheelbrace 1 .
6. R e fi t t h e t r i m .
7. Store the tools and the wheel in
the boot.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
- have the tighteness of the bolts and the pressure of the spare
wheel checked as soon as
possible,
- have the punctured wheel r e p a i r e d a n d r e fi t i t o n t h e v e h i c l e
as soon as possible.
Contact a CITROËN dealer or a
q u a l i fi e d w o r k s h o p . Front lamps
1. Sidelamps
2. Direction indicators
3. Dipped/Main beam headlamps
Page 79 of 97
9
74
PRACTICAL INFORMATION
CHANGING A BULB
1. Sidelamps (W5 W)
Turn the bulb holder A one quarter
of a turn and remove it.
Remove the bulb and change it.
2. Direction indicators (PY 21 W amber)
Turn the bulb holder B one quarter
of a turn and remove it.
Turn the bulb one quarter of a
turn.
Remove the bulb and change it.
I f y o u e n c o u n t e r a n y d i f fi c u l t i e s , c o n -
t a c t a C I T R O Ë N d e a l e r o r a q u a l i fi e d
workshop.
In certain climatic conditions
(low temperatures, humidity),
the presence of condensa-
tion on the internal face of
the headlamps is normal ; it disap-
pears a few minutes after the lighting
is switched on.
Never go underneath a vehi-
cle supported only by a jack
(use an axle stand).
4. Fold the jack 2 and detach it.
5. Tighten the wheel bolts using the
wheelbrace 1 .
6. R e fi t t h e t r i m .
7. Store the tools and the wheel in
the boot.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
After changing a wheel:
- have the tighteness of the bolts and the pressure of the spare
wheel checked as soon as
possible,
- have the punctured wheel r e p a i r e d a n d r e fi t i t o n t h e v e h i c l e
as soon as possible.
Contact a CITROËN dealer or a
q u a l i fi e d w o r k s h o p . Front lamps
1. Sidelamps
2. Direction indicators
3. Dipped/Main beam headlamps
Page 81 of 97
9
77
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE REPEATERS (WY 5 W AMBER)
Push the repeater forwards or
rearwards and detach it by pulling
towards you.
Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuseboxes are located under the
instrument panel trim and next to the
battery in the engine compartment.
Good
Removing and fitting a fuse
Before changing a fuse, the cause of
the incident must be found and recti-
fi e d .
Use the tweezer A located in the
fusebox under the bonnet.
Failed
Tweezer A Instrument panel fuseboxes
These are located on each side of
the instrument panel under the trim.
Turn the steering wheel to the left,
remove bolt B .
Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key),
remove bolt C .
Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Page 84 of 97
9
77
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE REPEATERS (WY 5 W AMBER)
Push the repeater forwards or
rearwards and detach it by pulling
towards you.
Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuseboxes are located under the
instrument panel trim and next to the
battery in the engine compartment.
Good
Removing and fitting a fuse
Before changing a fuse, the cause of
the incident must be found and recti-
fi e d .
Use the tweezer A located in the
fusebox under the bonnet.
Failed
Tweezer A Instrument panel fuseboxes
These are located on each side of
the instrument panel under the trim.
Turn the steering wheel to the left,
remove bolt B .
Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key),
remove bolt C .
Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Page 85 of 97
9
77
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE REPEATERS (WY 5 W AMBER)
Push the repeater forwards or
rearwards and detach it by pulling
towards you.
Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuseboxes are located under the
instrument panel trim and next to the
battery in the engine compartment.
Good
Removing and fitting a fuse
Before changing a fuse, the cause of
the incident must be found and recti-
fi e d .
Use the tweezer A located in the
fusebox under the bonnet.
Failed
Tweezer A Instrument panel fuseboxes
These are located on each side of
the instrument panel under the trim.
Turn the steering wheel to the left,
remove bolt B .
Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key),
remove bolt C .
Always replace a faulty fuse
with a fuse of the same rating
(same colour).
Page 92 of 97
9
84
PRACTICAL INFORMATION
TOWING THE VEHICLE
Your vehicle can only be towed at
the front.
Lifting (2 wheels only
on the road)
Never use the radiator crossmember.
Towing with fours wheels on the road
must be carried out at very low speed
over a very short distance (in accor-
dance with the legislation in force).
In all other cases, your vehicle must
be transported on a trailer.
Without lifting
(4 wheels on the road)
The removable towing eye is stored
in the spare wheel, under the boot
carpet.
Unclip the bottom of the cover,
Screw in the towing eye until it locks.
Place the gear lever in posi-
tion N for the "SensoDrive"
gearbox.
FITTING ROOF BARS
Please refer to national legis-
lation in order to comply with
the regulations concerning the
transportation of objects which
are longer than the vehicle.
Vehicles fitted with a manual
gearbox
I n t h e c a s e o f v e h i c l e s fi t t e d w i t h a
manual gearbox, the gear lever must
be in the neutral position.
Failure to observe this special con-
dition may result in damage to cer-
tain braking components and the
absence of braking assistance the
next time the engine is started.
W h e n fi t t i n g t r a n s v e r s e r o o f b a r s ,
use the accessories recommended
by CITROËN and follow the manu-
f a c t u r e r ' s fi t t i n g i n s t r u c t i o n s .
For more information, contact a
C I T R O Ë N d e a l e r o r a q u a l i fi e d w o r k -
shop.
Maximum weight authorised on
the bars, for a loading height not
exceeding 40 cm (except bicycle
carrier): 50 kg.
If the height exceeds 40 cm, adapt
the speed of the vehicle to the pro-
fi l e o f t h e r o a d t o a v o i d d a m a g i n g
the roof bars.
General
recommendations
Observe the legislation in
force in your country.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must stay at the wheel of
the towed vehicle.
Driving on motorways and fast roads
is prohibited when towing.
When towing a vehicle with all four
wheels on the ground, always use an
approved towing bar; rope and straps
are prohibited.
When towing a vehicle with the en-
gine off, there is no longer any power
assistance for braking or steering.
In the following cases, you must al-
ways call on a professional recovery
service:
- vehicle broken down on a motorway or fast road,
- when it is not possible to put the gearbox into neutral, unlock the
steering, or release the parking
brake,
- towing with only two wheels on the ground,
- where there is no approved towing bar available...
Page 93 of 97
9
85
PRACTICAL INFORMATION
ACCESSORIES
A wide range of accessories and
genuine parts is available from the
CITROËN dealer network.
These accessories and parts have
been tested and approved for reli-
ability and safety.
They are all adapted to your vehicle
a n d b e n e fi t f r o m C I T R O Ë N ' s r e c o m -
mendation and warranty. Installation of radio
communication transmitters
Before installing any after-market
radio communication transmitter,
you can contact a CITROËN dealer
f o r t h e s p e c i fi c a t i o n o f t r a n s m i t t e r s
w h i c h c a n b e fi t t e d ( f r e q u e n c y , m a x i -
m u m p o w e r , a e r i a l p o s i t i o n , s p e c i fi c
installation requirements), in line with
the Vehicle Electromagnetic Compat-
ibility Directive (2004/104/EC).
Depending on the legisla-
tion in force in the country, it
may be compulsory to have
a high visibility safety vest,
warning triangle and spare bulbs and
fuses available in the vehicle.
T h e fi t t i n g o f e l e c t r i c a l e q u i p m e n t o r a c -
cessories which are not recommended
by CITROËN may result in a failure of
your vehicle's electronic system and
excessive electrical consumption.
Please note this precaution. You
are advised to contact a CITROËN
representative to be shown the range
of recommended equipment and
accessories.
* France only.
"Comfort": front and rear parking
sensors, portable ashtray, glove box
lid, insulated module, centre armrest,
b a b y b a g , r e a d i n g l a m p , d o o r d e fl e c -
tors, sun blinds, ...
"Transport solutions": boot liner,
roof bars, bicycle carrier, ski carrier,
r i g i d a n d fl e x i b l e r o o f b o x e s , b o o t d i -
viders, canoe carrier, ...
You can obtain "Van" conversion
kits to convert a private vehicle to a
van * .
"Styling": wheel trims, 14 inch alloy
wheels, 15 inch alloy wheels, spoiler,
exterior "aluminium look" and "car-
b o n fi b r e l o o k " s t y l i n g k i t s , a l u m i n i u m
interior trim kit, "aluminium look" and
" c a r b o n fi b r e l o o k " d o o r m i r r o r s h e l l s ,
chromed exhaust tailpipe, leather
s t e e r i n g w h e e l , c h r o m e g r i l l e fi n i s h e r . . .
"Security and safety": anti-theft alarm,
wheel security bolts, snow chains and
non-slip covers, high visibility vest,
warning triangle, breathalyzer, child
s e a t s , fi r s t a i d k i t , fi r e e x t i n g u i s h e r , f o -
glamp kit, ...
"Protection": mats, seat covers,
m u d fl a p s , s i d e p r o t e c t i o n r u b b i n g
strips, door sill protectors, boot sill
protectors, vehicle cover, ...
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned and secured correctly,
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
"Multimedia": semi-integral navi-
gation system, portable satellite
navigation system, USB Box, audio
systems, speakers, rear parcel shelf
with speakers, Bluetooth hands-free
system, speed camera detectors,
DVD player, mapping update CD,
auxiliary cable for audio equipment,
CD storage, ...