stop start CITROEN C1 2022 User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2022, Model line: C1, Model: CITROEN C1 2022Pages: 269, PDF Size: 7.63 MB
Page 72 of 269

70
C1_en_Chap04_conduite_ed01-2016
A few driving recommendations
Observe the driving regulations at all times and remain  vigilant  whatever  the  traffic  conditions.
Pay
 close  attention  to  the  traffic  and  keep  your Â
h
ands  on  the  wheel  so  that  you  are  ready  to Â
r
eact  at  any  time  to  any  eventuality.
On
 a  long  journey,  a  break  every  two  hours  is Â
s
trongly
 re
commended.
In
 difficult  weather,  drive  smoothly,  anticipate Â
t
he  need  to  brake  and  increase  the  distance Â
f
rom  other  vehicles. Never
 drive  with  the  parking  brake Â
a
pplied  -  Risk  of  overheating  and Â
d
amage  to  the  braking  system!
Do
 not  park  or  run  the  engine  when Â
s
tationary  in  areas  where  inflammable Â
s
ubstances  and  materials  (dry  grass, Â
d
ead  leaves...)  might  come  into Â
c
ontact with  the  hot  exhaust  system  - Â
R
isk  of  fire!
Never
 leave  a  vehicle  unsupervised Â
w
ith  the  engine  running.  If  you  have Â
t
o  leave  your  vehicle  with  the  engine Â
r
unning,  apply  the  parking  brake Â
a
nd  put  the  gearbox  into  neutral  or Â
p
osition
N,
 depending  on  the  type  of Â
g
earbox.
Driving on flooded
roads
We strongly advise against driving on flooded roads,  as  this  could  cause  serious  damage Â
t
o  the  engine  or  gearbox,  as  well  as  to  the Â
e
lectrical  systems  of  your  vehicle.
Important!If you are obliged to drive through water:
- Â
c
heck  that  the  depth  of  water  does  not Â
e
xceed  15  cm,  taking  account  of  waves Â
t
hat  might  be  generated  by  other  users,
-
Â
d
eactivate  the  Stop  &  Start  system,
-
Â
d
rive  as  slowly  as  possible  without Â
s
talling.  In  all  cases,  do  not  exceed  6  mph Â
(
10Â km/h),
-
Â
d
o  not  stop  and  do  not  switch  off  the Â
e
ngine.
On
 leaving  the  flooded  road,  as  soon  as Â
c
ircumstances  allow,  make  several  light  brake Â
a
pplications  to  dry  the  brake  discs  and  pads.
If
 in  doubt  on  the  state  of  your  vehicle,  contact Â
a
 CITROËN  dealer  or  a  qualified  workshop.
Driving
Page 74 of 269

72
C1_en_Chap04_conduite_ed01-2016
If you use the ancillaries for a prolonged period,  the  vehicle  will  automatically Â
s
witch to " OFF"
 mode  after  about Â
20
 m
inutes.
Be aware
Â
in  order  to  avoid  discharging Â
t
he  battery.
Starting - switching off the engineÂ
w ith  the  Keyless  Entry  and  Starting Â
system
Changing the mode of the
vehicle
With the electronic key inside the v
ehicle;  each  press  on  the  "S TA R T/
STOP " button, with no action on the
pedals,
 changes  the  vehicle's  mode:
F
Â
F
irst
Â
press  ("ACC "
 mode).
 T
he
Â
ancillaries  (radio,  12V  socket...)  can  be Â
u
sed.
F
Â
S
econd  press  ("ON "
 mode).
 I
gnition  on.
F
Â
T
hird
Â
press  ("OFF "
 mode).
Avoid
Â
attaching
Â
heavy
Â
objects
Â
to
Â
the
 k
ey,
Â
which
Â
would
Â
weigh
Â
down
Â
on
Â
its
Â
b
lade
Â
in
Â
the
Â
ignition
Â
switch
Â
and
Â
could
Â
c
ause
Â
a
Â
malfunction.
F
Â
I
mmobilise
Â
the
Â
vehicle.
Switching off
FÂ With
 a  manual  gearbox:  put  the  gear  lever  i
nto  neutral.
F
Â
W
ith  an  ETG  gearbox:  place  the  selector  at Â
p
osition N .
F
Â
T
urn  the  key  towards  you  to  position  2 (ACC).
F
Press in and turn the key to position 1 (LOCK) .F Remove  the  key  from  the  ignition  switch.
F  T urn  the  steering  until  the  steering  column Â
l
ocks.
Driving
Page 75 of 269

73
C1_en_Chap04_conduite_ed01-2016
Starting using the
electronic key
With the first press on the "S TA R T/
STOP "
 button,  this  indicator  lamp f
lashes  slowly  in  the  instrument  panel.Depending
 on  the  ambient  temperature, Â
e
ach  attempt  at  starting  can  take  up  to Â
a
round  30  seconds.  During  this  period, Â
d
o  not  press  the  "START/STOP " button
again,
 or  release  the  clutch  pedal  or Â
b
rake  pedal  (depending  on  the  type  of Â
g
earbox).
After
 this  period,  if  the  engine  has  not Â
s
tarted,  press  the  "START/STOP "
button
 again  for  another  attempt  at Â
s
tarting. If
 one  of  the  starting  conditions  is Â
n
ot  met,  the  "Keyless  Entry  and Â
S
tarting"  system  indicator  lamp  flashes Â
i
n  the  instrument  panel.  In  some Â
c
ircumstances,  it  is  necessary  to Â
t
urn  the  steering  wheel  slightly  while Â
p
ressing  the  "
START/STOP " button to
assist  unlocking  of  the  steering.
For vehicles fitted with a manual gearbox:
F
Â
W
ith
Â
the  electronic  key  inside  the  vehicle, Â
p
ut
Â
the  gear  lever  into  neutral  and  fully Â
d
epress  the  clutch  pedal. The
 presence  of  the  electronic  key  in  t
he  vehicle  is  essential  for  switching Â
o
n  the  ignition  and  starting  only.  Once Â
t
he  engine  has  started,  make  sure  that Â
t
he  electronic  key  remains  with  the Â
v
ehicle  until  the  end  of  the  journey: Â
o
ther wise  you  would  not  be  able  to  lock Â
t
he vehicle.
F
Â
P
ress  and  release  the  "S TA R T/
STOP "
 button.
This
 indicator  lamp  comes  on  in  the Â
in
strument
 pan
el. For vehicles fitted with an ETG gearbox:
F
Â
W
ith  the  electronic  key  inside  the  vehicle, Â
p
ut  the  gear  selector  at  N  and  press  the Â
b
rake
 ped
al.
This  indicator  lamp  comes  on  in  the Â
in
strument
 pan
el.
F Â
P
ress  and  release  the  "
S TA R T/
STOP " Â button.
4
Driving
Page 76 of 269

74
C1_en_Chap04_conduite_ed01-2016
There is an audible signal when the driver's door is  opened  and  the  vehicle  is  in  "ACC "
 mode.
If
 the  vehicle  is  not  immobilised,  the Â
e
ngine  will  not  stop.
Switching off using the
electronic key
FÂ Immobilise
 the  vehicle.
F  W ith  a  manual  gearbox:  put  the  gear  lever Â
i
nto  neutral.
F
Â
W
ith  an  ETG  gearbox:  place  the  gear Â
s
elector at N .
F
Â
W
ith  the  electronic  key  inside Â
t
he vehicle, press the " S TA R T/
STOP "
 button.
The
 engine  stops.
The
 steering  locks  when  a  door  is  opened  or  on Â
l
ocking  the  vehicle.
F
P
ress the "START/STOP " button
again
 to  change  to  "OFF "
 mode.
Emergency starting
When the electronic key is in the recognition  zone  and  your  vehicle Â
d
oes  not  start  after  pressing  the Â
"ST
ART/STOP "
 button,  this  warning Â
l
amp  flashes  in  the  instrument  panel.
F
Â
W
ith
Â
a  manual  gearbox:  put  the  gear  lever Â
i
nto
Â
neutral.
F
Â
W
ith
Â
an  ETG  gearbox:  place  the  selector Â
l
ever at N . F
Â
P
ut  the  corner  of  the  electronic  key,  where Â
t
he  indicator  lamp  is  located,  in  contact Â
w
ith the "
START/STOP " Â button.
 T
here  is  an  audible  signal  when  the Â
e
lectronic  key  is  recognised;  the  vehicle Â
c
hanges  to  "
ON " Â mode.
F Â
W
ith  a  manual  gearbox:  press  the  clutch Â
p
edal  fully  down.
F Â
W
ith  an  ETG  gearbox:  press  the  brake Â
ped
al.
F Â
C
heck  that  the  "Keyless  Entry  and  S
tarting"  indicator  lamp  comes  on  in  green  i
n  the  instrument  panel.
F
P
ress the "START/STOP "
 button.
 T
he  engine  starts.
If
 the  engine  does  not  start,  contact  a Â
C
ITROËN  dealer  or  a  qualified  workshop.
Driving
Page 77 of 269

75
C1_en_Chap04_conduite_ed01-2016
Emergency switch-off
In the event of an emergency only, the engine can  be  switched  of  without  conditions.  To  do Â
t
his,  press  for  more  than  2  seconds,  or  make Â
a
 minimum  of  3  successive  presses  on  the Â
"ST
ART/STOP "
 button.
In
 this  case  the  steering  column  locks  as  soon Â
a
s  the  vehicle  stops.
Electronic key not
recognised
If the electronic key is no longer in the recognition  zone  when  driving  or  when  you Â
(
later)  request  switching  off  the  engine,  there  is Â
a
n  audible  signal  to  warn  you.
F
Â
P
ress  for  more  than  2  seconds, Â
o
r  make  a  minimum  of Â
3Â s
uccessive  presses  on  the Â
"ST
ART/STOP" button if you
want
 to  force  switching  off  of  the Â
e
ngine  (note that restarting
will not be possible without
the
key).
Electronic e ngineÂ
i
mmobiliser
This locks the engine management system as s
oon  as  the  ignition  has  been  switched  off  and Â
t
herefore  prevents  starting  of  the  vehicle  by Â
a
nyone  who  does  not  have  the  key.
The
 ignition  key  has  an  electronic  chip  which Â
h
as  a  special  code.  When  the  ignition  is Â
s
witched  on,  the  code  must  be  recognised  for Â
s
tarting  to  be  possible.
In
 the  event  of  a  malfunction,  your  vehicle  will Â
n
ot  start.
Contact
 a  CITROËN  dealer  or  a  qualified Â
w
orkshop. Do
 not  make  any  modifications  to  the Â
e
lectronic  immobiliser  system.
4
Driving
Page 82 of 269

80
C1_en_Chap04_conduite_ed01-2016
The vehicle can be stopped whatever the position  of  the  gear  selector  (N , E or R ).
However,
 there  is  an  audible  signal  on  opening Â
t
he  driver's  door  if  the  gear  selector  is  not  at Â
p
osition N .
Switching off
When the vehicle is stopped with the e
ngine  running,  always  put  the  gear Â
s
elector to neutral N .
There
 is  a  continuous  audible  signal Â
i
f  you  turn  the  ignition  switch  to  "OFF "
with
 the  vehicle  in  2
nd, 3rd, 4th or 5th ge a r.
In
Â
this
Â
case
Â
return
Â
the
Â
ignition
Â
switch Â
t
o " ON ",
Â
move
Â
the
Â
gear
Â
selector
Â
to Â
p
osition
N , then to position E , M or R,
then
Â
turn
Â
the
Â
ignition
Â
switch
Â
to
Â
" OFF ".
On
Â
a
Â
slope,
Â
use
Â
the
Â
brakes
Â
to
Â
i
mmobilise
Â
the
Â
vehicle
Â
and
Â
place
Â
the Â
g
ear
Â
selector
Â
in
Â
position
Â
N , E or R . With
 the  ignition  on,  illumination Â
o
f  this  warning  lamp  indicates  a Â
g
earbox  fault.
Contact  a  CITROËN  dealer  or  a Â
q
ualified
 w
orkshop.
Operating faults
In all cases, it is essential
that you
apply the parking brake to  immobilise Â
t
he  vehicle.
Before
 doing  anything  under  the Â
b
onnet,  check  that  the  gear  selector  is Â
i
n neutral N  and  the  parking  brake  is Â
a
pplied.
Limits of operation
On a gradient, or when hill start assist is activated, n ever hold the vehicle using the
accelerator :
 you  could  damage  the  clutch.
In
 these  situations  there  is  an  audible  signal.
F
Â
M
ove  the  gear  selector  to  position  N.
F
Â
W
ait  15  minutes  to  allow  the  clutch  to  cool Â
d
own  before  setting  off. -
Â
c
heck  that  the  ignition  switch  is  at  the Â
"
O
N
"
position,
- Â
p
lace  the  gear  selector  at  N
,  then  move  it Â
t
o E
, M or R .
If 1  is  flashing  in  the  instrument  panel:
-  p lace  the  gear  selector  at  E or M
, then
move  it  to  N.
If R
 is  flashing  in  the  instrument  panel:
-
Â
p
lace  the  gear  selector  at  R,
 then  move  it Â
t
o N.
If
N is  flashing  in  the  instrument  panel
 a
ccompanied  by  an  audible  signal  for  a  long  time:
Driving
Page 85 of 269

83
C1_en_Chap04_conduite_ed01-2016
Stop & Start (VTi 68 S&S engine)
Operation
Going into engine STOP
mode
This indicator lamp comes on in the instrument  panel  and  the  engine Â
g
oes  into  standby  automatically:
-
Â
w
hen
 stationary,  in  neutral,  and  you Â
r
elease  the  clutch  pedal.
Never
 refuel  with  the  engine  in Â
S
TOP mode;  you  must  switch  off  the Â
i
gnition  with  the  button.
For
 smoother  operation,  during  p
arking  manoeuvres  STOP  mode  is  n
ot  available  for  a  few  seconds  after Â
c
oming  out  of  reverse  gear.
The
 Stop  &  Start  does  not  affect  the Â
v
ehicle's  systems,  such  as  for  example, Â
b
raking,  power  steering...
The
Â
Stop
Â
&
Â
Start system
Â
puts
Â
the
Â
engine
Â
t
emporarily
Â
into
Â
standby
Â
-
Â
STOP
Â
mode
Â
-
Â
during
Â
s
tops
Â
in
Â
the
Â
traffic
Â
(red
Â
lights,
Â
traffic
Â
jams,
Â
or
 o
ther...).
Â
The
Â
engine
Â
restarts
Â
automatically
Â
-
 S
TART
Â
mode
Â
-
Â
as
Â
soon
Â
as
Â
you
Â
want
Â
to
Â
move
Â
o
ff.
Â
The
Â
restart
Â
takes
Â
place
Â
instantly,
Â
quickly
Â
a
nd
Â
silently.
Per fect
Â
for
Â
urban
Â
use,
Â
the
Â
Stop
Â
&
Â
Start
Â
system
Â
r
educes
Â
fuel
Â
consumption
Â
and
Â
exhaust
Â
e
missions
Â
as
Â
well
Â
as
Â
the
Â
noise
Â
level
Â
when
Â
s
tationary.
Stop & Start time counters
A partial time counter counts the periods in S TOP  mode  during  a  journey.
It
 is  displayed  in  the  trip  computer  once  the Â
S
top  &  Start  is  operating.
Press one of the " DISP" buttons to return to the
previous
 d
isplay.
A
 global  time  counter  counts  the  periods  in Â
S
TOP  mode  since  the  last  reset.
When
 it  is  displayed,  press  one  of  the Â
"D
ISP "Â buttons
 to  reset  the  counter.
4
Driving
Page 86 of 269

84
C1_en_Chap04_conduite_ed01-2016
Going into engine START
mode
This indicator lamp goes off and the engine s tarts a utomatically:
-
Â
w
hen
 you  fully
Â
depress  the  clutch  pedal.
START
Â
mode  is  invoked  automatically  when:
-
Â
y
ou
Â
open  the  driver's  door,
-
Â
y
ou
Â
open  the  bonnet,
-
Â
y
ou
Â
unfasten  the  driver's  seat  belt,
-
Â
s
ome
 special  conditions  (battery  charge, Â
e
ngine  temperature,  braking  assistance, Â
d
escending  a  steep  gradient,  adjustment  of Â
t
he
Â
air  conditioning...)  where  the  engine  is Â
n
eeded  for  control  of  a  system.
Special cases: START invoked
automatically
In the event  o f  a  f ault  w ith  t he  s ystem,  t
his  warning  lamp  flashes  in  the Â
in
strument
 pan
el.
Operating fault
Have it checked by a CITROËN dealer or a qualified w orkshop.
Special cases: STOP mode not
available
STOP mode is not invoked principally when:
-  t he  driver's  door  is  open,
-
Â
t
he  driver's  seat  belt  is  not  fastened,
-
Â
t
he  engine  is  needed  to  maintain  a Â
c
omfortable  temperature  in  the  passenger Â
c
ompartment,
-
Â
d
emisting  is  active,
-
Â
s
ome  special  conditions  (battery  charge, Â
e
ngine  temperature,  braking  assistance, Â
v
ehicle  stopped  on  a  steep  gradient,  high Â
a
ltitude...)  where  the  engine  is  needed  to Â
a
ssure  control  of  a  system.
Driving
Page 87 of 269

85
C1_en_Chap04_conduite_ed01-2016
At any time, press this button to deactivate the system.
Manual deactivation /
reactivation
If the system has been deactivated in S TOP mode,  the  engine  restarts  immediately.
The
 system  is  reactivated  automatically  at Â
e
very  new  engine  start  by  the  driver.
Press
 this  button  again.
The
 system  is  active  again;  this  is  confirmed  by  the
 i
ndicator  lamp  going  off  in  the  instrument  panel.
Deactivation
 is  confirmed  by  the Â
i
llumination  of  this  indicator  lamp  in Â
t
he  instrument  panel.
Before
Â
doing
Â
anything
Â
under
Â
the
Â
b
onnet,
Â
deactivate
Â
the
Â
Stop
Â
&
Â
Start
Â
s
ystem
Â
to
Â
avoid
Â
any
Â
risk
Â
of
Â
injury
Â
r
esulting
Â
from
Â
automatic
Â
operation
Â
of
Â
S
TART
Â
mode.
Maintenance
The Stop & Start system requires a 12 V b
attery  of  a  special  specification  and Â
t
echnology.
All
 work  on  this  type  of  battery  must  be Â
d
one  only  by  a  CITROËN  dealer  or  a Â
q
ualified
 w
orkshop.
For
 more  information  on  the  12  V Â
b
attery,  refer  to  the  corresponding Â
s
ection.
4
Driving
Page 110 of 269

108
C1_en_Chap06_securite_ed01-2016
Illumination of this warning lamp, accompanied  by  an  audible  signal, Â
i
ndicates  that  there  is  a  fault  with  the Â
e
lectronic  brake  force  distribution Â
(
EBFD),  which  could  cause  loss  of Â
c
ontrol  of  the  vehicle  when  braking.
Operation
Illumination of this warning lamp, accompanied  by  an  audible  signal, Â
i
ndicates  that  there  is  a  fault  with Â
t
he  ABS  system,  which  could  cause Â
l
oss of control of the vehicle when
braking.
Anti-lock braking system (ABS)
and electronic brake force
distribution (EBFD)When changing  w heels  ( tyres  a nd  r ims),  m
ake  sure  that  these  are  approved  for Â
y
our  vehicle.
Normal
 operation  of  the  ABS  may  make Â
i
tself  felt  by  slight  vibration  of  the  brake Â
ped
al.
In emergency braking, press
very firmly without releasing
the
pressure.
Yo u must
Â
stop
Â
as
Â
soon
Â
as
Â
it
Â
is
Â
safe
Â
to
Â
do
Â
so.
Contact
Â
a
Â
CITROËN
Â
dealer
Â
or
Â
a
Â
qualified
Â
w
orkshop
Â
as
Â
soon
Â
as
Â
possible.
Dynamic stability control (DSC)
and traction control (TRC)
Activation
These systems are activated automatically e ach  time  the  vehicle  is  started.
As
 soon  as  they  detect  a  problem  of  grip  or Â
t
rajectory,  these  systems  act  on  the  operation  if Â
t
he  engine  and  brakes.
Activation
 of  the  DSC  system  is
 s
ignalled  by  the  flashing  of  this
 i
ndicator  lamp  in  the  instrument  panel,
 a
ccompanied  by  an  audible  signal.
Activation
 of  the  TRC  system  is
 s
ignalled  by  the  flashing  of  this
 i
ndicator  lamp  in  the  instrument  panel.
Drive
Â
carefully
Â
at
Â
reduced
Â
speed,
Â
and
Â
contact
Â
a
Â
C
ITROËN
Â
dealer
Â
or
Â
a
Â
qualified
Â
workshop.
Safety