shaft Citroen C2 2004 1.G Owners Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2004, Model line: C2, Model: Citroen C2 2004 1.GPages: 523, PDF Size: 10.32 MB
Page 317 of 523
Downloaded from www.Manualslib.com manuals search engine 313
CLUTCH
GEARBOX
TRANSMISSION
MA/5 PILOTED MANUAL GEARBOX
Engines: KFV 8HX
(1)Circlip.(2) Secondary shaft.(3) Drive pinion (5th gear).(4)Bearing stop screw.(5) Gearbox casing.(6)Intermediate plate.(7) Gearbox casing fixing screw.(8)Clutch bearing guide screw.(9)Clutch housing.(10)Bearing guide.(11)Primary shaft.(12)Differential housing.(13)Speedometer screw.(14)Counter drive.(15) Planet pinions.(16)Satellite pinions.(17) Differential gearwheel.(18)Driven pinion (1st gear).(19)1st / 2nd gear synchroniser and reverse gear driven pinion.(20)Driven pinion (2nd gear).(21)Driven pinion (3rd gear).(22)3rd and 4th gear synchroniser.B2CP3SRP
C2
Page 323 of 523
Downloaded from www.Manualslib.com manuals search engine 319
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX
Engines: NFV 6FZ RFN RFS 8HV 8HY 9HZ 9HY WJY RHY RHZ
Description
(1)
Primary shaft.
(2)Clutch bearing guide.
(3)Gearbox casing.
(4)Clutch housing.
(5)Reverse idle.
(6)Drive gear (3rd gear).
(7)3rd / 4th gear synchroniser.
(8)Drive gear (4th gear).
(9)Drive gear (5th gear).
(10)5th gear synchroniser.
(11)Driven gear (5th gear).
(12)Driven gear (2nd / 4th gear).
(13) Driven gear (2nd gear).
(14)1st / 2nd gear synchroniser.
(15)Driven gear (1st gear).
(16)Secondary shaft.
(17)Differential gear.
(18)Satellite gears.
(19)Planet gears.
(20)Differential housing.
(21)Speedometer drive.
(22)Extension.
«d» Adjusting shims: 0.7 to 2.4 mm
(0.10 mm and increasing by 0.10 mm).
«c»Adjusting shims:1.4 to 1.6 mm
(0.10 mm and increasing by 0.10 mm).
B2CP3BQP
C3 XSARA XSARA PICASSO
Page 324 of 523
Downloaded from www.Manualslib.com manuals search engine 320
CLUTCH
GEARBOX
TRANSMISSION
BE4/5 GEARBOX
Engines: 6FZ RFN RFS WJY 8HV 8HY 8HZ 9HZ 9HY RHY RHZ
Tightening torques (m.daN).
(23)
Clutch bearing guide (3 screws): 1,25 ± 0,2
(24)
Clutch housing (13 screws): 1,3 ± 0,2
(25)
Primary shaft nut (1 screw):7,25 ± 0,5
(26)
Secondary shaft nut (1 screw): 6,5 ± 0,5
(27)
Yoke retaining screw (2 screws): 1,5 ± 0,2
(28)
Differential gearwheel screw (2 screws): 6,5 ± 0,5
Reverse gear switch (1 screw): 2,5 ± 0,3
(29)
Differential housing (4 screws): 5 ± 0,5
(30)
Breather pipe:1,7 ± 0,2
(31)
Rear housing cover screws (7 screws):1,25 ±0,2
(32)
Top up plug (1 screw):2,2 ±0,2
(33)
Differential housing screws (4 screws):1,25 ±0,2
(34)
Drain plug (1 screw):3,5 ±0,3
B2CP3BRD
C3 XSARA XSARA PICASSO
Page 337 of 523
Downloaded from www.Manualslib.com manuals search engine 333
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: AL4 AUTOMATIC GEARBOX
Engines: KFV NFU RFN RHZ
Precautions to be taken.
Repairs on mechanical components.
Never place the gearbox on the ground without protection.
In order to avoid breaking the input shaft ring, it is
imperativethat
the converter retaining bracket should be in place when handlingthe gearbox.
It is
imperativeto use the centring peg and the converter retaining
bracket to couple the gearbox on the engine.
After coupling the gearbox on the engine, remove the centring peg.
Modification of the oil usage counter value.
Exchanging the gearbox ECU:
Note down the gearbox counter value.
Transfer the value read into the the new gearbox ECU.
Exchanging the gearbox :
Initialise the oil usage counter to 0.
Draining the gearbox:
Initialise the oil usage counter(follow the diagnostic tool procedure).
C3 XSARA XSARA PICASSO
Page 358 of 523
Downloaded from www.Manualslib.com manuals search engine 354
CLUTCH
GEARBOX
TRANSMISSION
DRIVESHAFTS GEARBOX
Tightening torques (m.daN)
Driveshaft
bearing Engines
V ehiclesGearboxRH side LH side Tool kitGearbox oil seal mandrels
24,5 ± 0,5
32 ± 1,5
32,5 ± 2,57114 T.W
Seal extractor
RH / LH
( ) 0338 C
( ) 0338 J1
+ ( ) 0338 J3( ) 0338 H1
+ ( ) 0338 H2
( ) 0338 J1
+ ( ) 0338 J2( ) 0338 H1
+ ( ) 0338 H2( ) 0338 7114 T.X
7116 T Driveshaft
nut
HFX KFV KFU
8HX 8HW
NFU
KFW NFU
NFV RFS RFN 6FZ WJY
8HZ 9HZ 9HY RHY RHZ
8HV 8HY
NFU RFN RHZ
KFV MA/5
XSARA
XSARA PICASSOC2 C3 C3 Pluriel
XSARANO
2 ± 0,2
1,8 ± 0,1
2 ±0,2
1,8 ±0,1
1 ±0,1
C3
C3
XSARA PICASSO
XSARA
Tightening torque (m.daN) for wheel bolts: XSARA = 8,5 ± 0,8 XSARA PICASSO = 10 ± 1 C2 C3 C3 PLURIEL = 9 ± 1BE4/5
AL 4
C2 C3 C3 PLURIEL XSARA XSARA PICASSO
Page 389 of 523
Downloaded from www.Manualslib.com manuals search engine 385
AXLES
SUSPENSION
STEERING
XSARA
FR ONT AXLE
Tightening torques (m.daN).
(1)
Damper nut: 4,5 ± 0,4
(2)Cup screw : 2,5 ± 0,3
(3)Suspension leg(4)Anti roll bar link rod upper ball joint: 3,7 ± 0,3
(5)Suspension leg pivot (hollow pivot): 4,5 ± 0,5
(5) Suspension leg pivot (pivot «H»): 5,5 ± 0,5
(6)Anti roll bars(7)Anti roll bar link rod lower ball joint:3,7 ± 0,3
(8)Pivot lower ball joint:4 ± 0,4
(9)Driveshaft nut: 32,5 ± 2,5
(10) Wheel bolt:9 ±1
(11)Lower arm front mounting: 7,6 ± 0,7
(12) Lower arm rear mounting
and anti roll bar bearing: 6,8 ± 0,6
(13)Screw under rear mounting: 3,1 ± 0,3
(14) Ball joint fixing on lower arm:5 ±0,5Subframe to bodyshell fixing screw: 8,5 ± 0,8
B3CP040PB3CP041D
VehiclesRPO 8667#are all equipped
as standard with ventilated discs.
Page 397 of 523
Downloaded from www.Manualslib.com manuals search engine 393
AXLES
SUSPENSION
STEERING
XSARA
Steering wheel Manual steering
MANUAL STEERING SPECIFICATIONS
(a): LHD/RHD = White.
(L): Shaft length = 311 ± 1.5 mm.
(1) Steering wheel fitted with AIRBAG(according to equipment).
(4)Steering column adjustment lever.
Tightening torques (m.daN).
(2) AIRBAG to steering wheel fixing: 0.8 (3)Steering wheel fixing: 3.3 (5) Steering column to support fixing:2.3 (6)Steering cardan joint fixing:2.3
(b) = Locating bush.
The locating bush must be centred in the reference window before
tightening the cardan bolts
(6).
B3EP08PD
Page 400 of 523
Downloaded from www.Manualslib.com manuals search engine 396
AXLES
SUSPENSION
STEERING
XSARA POWER ASSISTED STEERING SPECIFICATIONS
Steering wheel Power assisted steering
(a): LHD = Blue.
: RHD = White.
(L): Shaft length = 311 ± 1.5 mm.
(1) Steering wheel fitted with AIRBAG(according to equipment).
(4)Steering column adjustment lever.
Tightening torques (m.daN).
(2) AIRBAGto steering wheel fixing: 0.8 (3)Steering wheel fixing: 3.3 (5)Steering column to support fixing: 2.3 (6)Steering cardan joint fixing: 2.3
(b) = Locating bush.
The locating bush must be centred in the reference
window before tightening the cardan bolts
(6).
B3EP08QD
Page 403 of 523
Downloaded from www.Manualslib.com manuals search engine 399
AXLES
SUSPENSION
STEERING
POWER ASSISTED STEERING SPECIFICATIONS
XSARA
Power assisted steering assembly
Tightening torques (m.daN).
High pressure tube (Rubber seal pump side)
Power assisted valve and pump union: 2.5
Return pipe.
Power assisted valve union: 2.5
(16)Upper front fixing (E3) : 2.5
(17) Upper rear fixing (E3) : 2.2
(18)Fixing (E3) : 2.2
Tightening sequence.
Tighten screws (16)and (18).
Lightly tighten screw
(17), then fully tighten.
Pressure switch on the pressure circuit.
Switch opens 30to 35 Bars.
Switch closes 25 Bars.
Tighten to :
2 m.daN. Power assisted steering system capacity =
1 litre.
Oil type:TOTAL FLUIDE ATX.
SAGINAW Pump adjustment = 100 Bars ± 5.
Pump shaft threading 3/8 16 threads per inch.
B3EP045D
Page 414 of 523
Downloaded from www.Manualslib.com manuals search engine 410
AXLES
SUSPENSION
STEERING
POWER ASSISTED STEERING SPECIFICATIONS
Tightening torques (m.daN).
Unions between pump unions and
power steering valve: 2 ± 0.3
(16)Fixing screw: 2.2 ± 0.3
(17)Fixing screw: 2.2 ± 0.3
(18)Fixing screw: 2.2 ± 0.3
NOTE:
Coat the threads with product «E3».
A pressure switch is implanted in the hydraulic piping between the
high pressure pump and the power steering valve. Opening pressure =
30 / 35 Bars.
Closing pressure = 25 Bars minimum.
Tightening torque = 2 ± 0.2.
Capacity of power steering circuit =
1 Litre.
Oil quality = TOTAL FLUIDE ATX.
Power steering pump: Supplier SAGINAW.
Pump adjustment = 100 ± 5 Bars.
Pump shaft threading 3/8 16 threads per inch.
B3EP118D
XSARA PICASSO