Filter Citroen C2 2004 1.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 261
INJECTION
XSARA PICASSO
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Engines: RHY RHZ
Tools.
[1] Ø 10 mm
low pressure connector: 4215T.
[2] Ø 8 mmlow pressure connector: 4218 T.
[3]Pressure gauge for testing boost pressure: 4073 T Kit 4073 T
Connect the tool [1]between the booster pump and the fuel filter (white mark at "a" on the
fuel supply pipe).
Connect the tool [2]downstream of the diesel injectors, between the high pressure fuel
pump and the fuel filter (green mark at "b"on the fuel return pipe).
WARNING: Any check of pressure downstream of the fuel filter is PROHIBITED.
Checks on pressure:static.
Switch on ignition
For 3 seconds(normal functioning):
Fuel supply pressure shown by the pressure gauge [3] = 1.8 ± 0.4 Bar. Fuel return pressure shown by the pressure gauge [3] = 0.5 ± 0.4 Bar.
B1BP1TWD

Downloaded from www.Manualslib.com manuals search engine 262
INJECTION
XSARA PICASSO CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Engines: RHY RHZ (continued)
Checks on pressure: dynamic.Engine running, at idle (normal functioning):
Fuel supply pressure shown by the pressure gauge [3] = 2 ± 0.4 Bar. Fuel return pressure shown by the pressure gauge [3] = 0.7 ± 0.4 Bar.
Abnormal functioning
Impossible to start the engine:
Fuel supply pressure less than 0.8 Bar:
Check the low pressure regulator incorporated in the filter (locked open). Check the high pressure pump distribution valve (locked shut).
Check: diesel injector return flow.(Table below)
Uncouple the diesel injector return pipe.
Fuel supply pressure Fuel return pressure Checks
Between 3and 3.5 Bar 0,7 ± 0,2 BarCheck the condition of the diesel filter
More than
3.5 Bar
More than 3.5 Bar
Less than 0.7 Bar
More than 0.7 Bar
Check the low pressure regulator incorporated in
the filter (locked shut): replace.
Check the fuel return circuit
(pipe pinched or trapped…)
Between 0.8 and 1.5 BarLess than 0.7 BarCheck the fuel suppy circuit:
Booster pump (low pressure), piping.
Check:
Observe:
The flow should be drop by drop.
Diesel injector functioning correctly.
Excessive fuel return.
Diesel injector locked shut.

Downloaded from www.Manualslib.com manuals search engine 271
INJECTION
CHECKS: EXHAUST GASES RECYCLING CIRCUIT
Engines: 9HZ 9HY
B1HP1UPC
B1HP1UQC
XSARA PICASSO
Exhaust gas recycling (EGR) valve.
(1)
Exhaust gas recycling (EGR) electrovalve
NOTE:The engine ECU pilots the EGR valve.
Perform the check with the aid of a diagnostic tool.
Carry out the following operations with the diagnostic tool:
«INJECTION» menu.
Actuator tests.
EGE electrovalve.
Check that you can hear the click from the EGR regulation electrovalve.
Double butterfly housing (vehicle with particle filter).
(2)
Double butterfly housing.
Perform the check with the aid of a diagnostic tool.
Carry out the following operations with the diagnostic tool:
«INJECTION» menu.
Actuator tests.
Butterfly.
EGR exchanger butterfly.
Check that you can hear the click from the double butterfly housing.

Downloaded from www.Manualslib.com manuals search engine 273
INJECTION
PARTICLE FILTER SAFETY AND CLEANLINESS REQUIREMENTS
General.
ESSENTIAL: Given the very high pressures prevailing in the fuel high pressure circuit (1600 Bars), respect the following regulations.
It is forbidden to smoke in the immediate proximity of the high pressure circuit during a repair.
Avoid working close to flames or sparks.When the engine is running:
Do touch the fuel high pressure circuit.
Always keep out of range of possible projections of fuel, which could cause serious injuries.
Do not place your hand near to any leak on the fuel high pressure circuit. After the engine has stopped, wait 30 seconds before starting any operation.
NOTE:The waiting time is necessary to allow the fuel high pressure circuit to return to atmospheric pressure.
Safety rules.
IMPERATIVE:Wait at least an hour before starting any repair on the exhaust line.
Forced regeneration of the particle filter:
Check that there are no aerosols or inflammable products inside the vehicle’s boot.
Wear high temperature gloves.
Connect the vehicle to a gas extractor approved for this type of operation.
IMPERATIVE: In the absence of the required installations, carry out the forced regeneration of the particle filter outside the workshop,
in a concreted area well away from any inflammable materials. Place the vehicle in the high position.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 274
INJECTION
PARTICLE FILTER SAFETY AND CLEANLINESS REQUIREMENTS
Operations on the fuel additive circuit.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves that are resistant to hydrocarbons.
The work area must be ventilated.
In the event of any significant dispersion of additive:
Wear a breathing mask for filtering the particles.
Recover as much of the product as possible.
Place the product thus recovered in an appropriately labelled container. Wash the soiled area with copious amounts of water.
Dispose of materials and solid residues in an authorised recovery point.
IMPERATIVE:The filling kit should be recycled following a repair. All «Eolys» additive containers that have been opened should be
disposed of.
Cleanliness rules.
ESSENTIAL: The operator should wear clean overalls.
Before working on the injection circuit, it may be necessary to clean the unions of the following sensitive components(see corresponding operations).
Fuel filter.
Fuel high pressure pump.
Fuel high pressure regulator.
Fuel high pressure common injection rail. Fuel high pressure piping. Diesel injector carriers.
IMPERATIVE: After dismantling, immediately blank the unions of the sensitive components with plugs, to prevent any ingress of impurities.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 275
INJECTION
SPECIAL FEATURES: FORCED REGENERATION OF THE PARTICLE FILTER
Tools.
Diagnostic stations: LEXIA or PROXIA
Imperative: Respect the safety and cleanliness requirements.
Forced regeneration of the particle filter.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
ESSENTIAL: Connect the vehicle to a gas extractor approved for this type of operation.In the absence of the required installations,carry out the forced regeneration of the particle filter outside the workshop, in a concreted
area well away from any inflammable materials. Place the vehicle in the high position.
WARNING:
Check that the fuel level is sufficient (at least 20 litres).
Start the engine and allow it to warm up (60°C minimum).
Connect the diagnostic tool to the vehicle’s central socket.
Trigger the regeneration cycle, with the diagnostic tool.
Automatic running of the regeneration cycle of the particle filter:
Autocheck by the engine ECU. Stabilisation of engine speed at
4000 rpm, operating with post injection.
Change to idling speed (for 30 seconds).
Stabilisation of engine speed at 3000 rpm, checking of the efficiency of the regeneration of the particle filter.
Change to idling speed.
NOTE:Let the engine run at idling speed for the benefit of cooling.
Stop the engine.
IMPERATIVE: Wait for at least an hour before any operation on the exhaust line.
ALL TYPES

Downloaded from www.Manualslib.com manuals search engine 276
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / FILLING OF THE ADDITIVE RESERVOIR
Imperative: Respect the safety and cleanliness requirements.
Tools.
Filling kit comprising the following items:1Container of Eolys2Filters2Tubes1Empty container2Hooks1Adaptor
Filling.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves
that are resistant to hydrocarbons.
Place the vehicle on a lift.
Disconnect the battery negative terminal.
Unclip the the factory filler connector
(1).
Couple the container of additive to the tube (2)using the adaptor and the tube (with tap)from the
filling kit.
Screw the filler connector on the additive container
(3)at «b».
Place the additive container (3)on the component lift.
Open the tap located on the filler connector at «a».
Tilt the additive container (3)(to facilitate the end of filling).
Close the tap at «a».
Remove the filler connector and the tube (4).
Couple the tube (2).
Reconnect the battery negative terminal.
IMPERATIVE: The filling kit should be recycled after this operation. Any «Eolys» additive
containers that have been opened should not be kept.
XSARA PICASSO
B1HP1UVC
C4BP1EGC

Downloaded from www.Manualslib.com manuals search engine 277
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / CHECKING THE ADDITIVE PUMP
Engine: 9 HZ
IMPERATIVE: Respect the safety and cleanliness requirements.
Tools.
[1]
Manual pressure/vacuum pump: FACOM DA 16
[2]Additive container: ().1613.G Kit 1613
Checks.
IMPERATIVE: Respect the safety and cleanliness requirements specific to HDi engines.
IMPERATIVE: For all operations on the additive circuit, wear protective goggles and gloves that are
resistant to hydrocarbons.
Place the vehicle on a lift.
Raise the vehicle
To test the flow of the additive pump :
Uncouple the tube
(1).
Couple tool [2]on the outlet «a»of the additive reservoir.
Operate for 50 secondsthe actuator test «Additive pump»with the aid of LEXIA or PROXIA.
IMPERATIVE:The volume collected by the tool [2] should be 20 ± 5 ml.
NOTE:
Replace the additive pump if it is defective.
Couple the tube (1).
Operate the actuator test «Filling the tube: additive pump – additive injector», with the aid of LEXIAorPROXIA.
B1HP1UTC
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 278
INJECTION
SPECIAL FEATURES: PARTICLE FILTER / CHECKING THE ADDITIVE PUMP
Sealing of the additive injector.
Couple tool [1] to the tube (1).
Action the manual pump [1].
WARNING:The additive injector should open at a pressure of 100 ± 20 Bars.
Action the manual pump in vacuum
[1]at 800 m.bars.
WARNING:The downstream pressure should not fall rapidly.
NOTE:Replace the fuel tank if the injector is defective.
Couple the tube
(1).
Operate the actuator test «Filling the tube: additive pump – additive injector», with the aid ofLEXIAor PROXIA.
Check the additive level.
The checking of the additive level is done with reference to the gradations «a»marked on the additive
reservoir.
The top graduation indicates maximum filling
(3 Litres).
The difference between the two gradations equates to 0,25 Litres.
XSARA PICASSO
B1HP1UUC
B1KP019C

Downloaded from www.Manualslib.com manuals search engine 311
CLUTCH
GEARBOX
TRANSMISSION
RECOMMENDATIONS PRECAUTIONS: MA PILOTED MANUAL GEARBOX
Engines: HFX KFV NFU 8HX
Engaging of «N», without using a diagnostic tool (continued).
Preliminary operation:
Disconnect the battery negative terminal.
Remove the air filter.
Use a
22 mmspanner.
Use the spanner to lift the gear engagement lever the maximum possible until
the axis
«A»of the engagement lever is perpendicular to the axis «B»(mid
point of the gear engagement lever).
When this position is attained, position
«N»is engaged.
B2CP3L8D
C2