Air Citroen C2 2004 1.G Manual PDF

Downloaded from www.Manualslib.com manuals search engine 416
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ABS REF
(a) Hydraulic circuit(b)Electrical circuit
(1)Master cylinder in tandem(2)Braking servo(3)Brake caliper (or drum at the rear)(4)Hub equipped with a bearing with an integral magnetic wheel(48 pairs of poles)(5)Wheel sensor(6)Brake fluid level sensor(7)Hydraulic block plus ECU(8)Stoplamp switch(9)Instrument panel(10)Diagnostic socket(11)Builtin systems interface (BSI)
B3GP02RP
C2

Downloaded from www.Manualslib.com manuals search engine 417
C2
BRAKE SPECIFICA TIONS
(7) Hydraulic blockBRAKESRef. Components Supplier Part no. Observations
ABS MK 70 Mounted on the front LH chassis
Hydraulic block 96 514 120 80 member.
ESP ABS MK.60 4 adjustment channels.
7 96 490 288 80
ABS MK.70
ECU ESP ABS 26way connector.
MK 60 Integral to the hydraulic block.
2way blue connector.
The sensors are inductivetype.
Front wheel sensor TEVES Mounted on the pivot
Nonadjustable airgap:
0.16 to 1.6 mm.
596 387 201 80Tightening torque:0.8 ±0.2 m.daN.
2way blue connector.
The sensors are inductivetype
Rear wheel sensor Mounted on the suspension arm.
Nonadjustable airgap
: 0,35 à 1,6 mm.
Tightening torque:0,8 ± 0,2 m.daN.
Hub equipped with a bearing with
4 Hub bearing SNR an integral magnetic wheel
(48 pairs of poles).B3FP7BVC

Downloaded from www.Manualslib.com manuals search engine 423
BRAKES
B3FP160C
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
With the bleeding apparatus.
Connect the bleeding apparatus [1]on the brake fluid reservoir (1).
Adjust the apparatus pressure to
2 Bars.
For each circuit:
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles. Close the bleed screw.
Remove the bleeding apparatus
[1].
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE:Two operators are necessary.
For each circuit:
Apply the brake pedal to place the circuit under pressure.
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw. Remove the tool
[1].
NOTE:Recommence the process a second time if that is necessary.
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
C2

Downloaded from www.Manualslib.com manuals search engine 430
BRAKES
BRAKE SPECIFICATIONS
Braking circuit with ABS REF
(a) Hydraulic circuit
(b)Electrical circuit
(1)Master cylinder in tandem
(2) Braking servo
(3)Brake caliper (or drum at the rear)
(4) Hub equipped with a bearing with an integral magnetic wheel
(48 pairs of poles)
(5) Wheel sensor
(6) Brake fluid level sensor
(7) Hydraulic block plus ECU
(8)Stoplamp switch
(9)Instrument panel
(10)Diagnostic socket
(11)Builtin systems interface (BSI)
B3GP02RP
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 433
BRAKES
BRAKE SPECIFICATIONS
Evolution: rear wheel cylinder (applies from RPO 9667)
C3 C3 Pluriel
Evolution.
New wheel cylinders at the rear, with cutoff pressure 27 bars instead of 35 bars.
Assembly.
(1)
Rear wheel cylinder.
Repair.
IMPERATIVE:The mixing of the old and new components is STRICTLY FORBIDDEN.
WARNING:
Identify the type of assembly prior to starting a repair.
ESSENTIAL: Systematically replace the wheel cylinders on both sides on the same axle.
Replacement parts.
Replacement Parts will market only the components for the new assembly.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 438
BRAKES
B3FP160C
BLEEDING AND FILLING THE BRAKING SYSTEM (Continued)
With the bleeding apparatus.
Connect the bleeding apparatus [1]on the brake fluid reservoir (1).
Adjust the apparatus pressure to
2 Bars.
For each circuit:
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container.
Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw.
Remove the bleeding apparatus
[1].
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
Without the bleeding apparatus.
NOTE:Two operators are necessary.
For each circuit:
Apply the brake pedal to place the circuit under pressure.
Connect a transparent tube onto the bleed screw, submerge the other end of the tube in a clean container. Open the bleed screw, wait until the fluid is flowing out without air bubbles.
Close the bleed screw.
Remove the tool
[1].
NOTE:Recommence the process a second time if that is necessary.
Check the brake fluid level
(should be between «MINI»level and «MAXI»level).
Fill if necessary with the approved and recommended synthetic brake fluid.
C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 448
BRAKESBRAKE SPECIFICATIONS
Electrical circuit
ComponentsRef.
SupplierPart no.Observations
42wayconnector.
Integral to the hydraulic block..Changing only the ECU is prohibited.
2waygrey connector.
The sensors are inductivetype.Tightening torque:
0,8 ± 0,2 m.daN.
2waygrey connector.
The sensors are inductivetype.Mounted on the brake caliper support.
Nonadjustable airgap:
0,3 to 1,2 mm.
Tightening torque:0,8 ±0,2 m.daN.
2waygrey connector.
The sensors are inductivetype.
Mounted on the suspension arm.
Nonadjustable airgap:
0,3 to 1,2 mm.
Tightening torque:0,8 ±0,2 m.daN.
Incorporated in the COM 2000.
6wayblue connector.
Located on the central console.
6way connector.
Toothed wheel:
48 teeth.
Integral with the driveshaft stub housing for
the front wheels, joined to the hub bearing for
the rear wheels.
XSARA
5.7 ESP
0 265 006 389
0 265 006 202
0 265 006 203
0 265 006 441 BOSCH
VALEO
BOSCH
GKNElectronic
ECU
Front wheel sensor
Rear wheel sensor
(disc brakes)
Rear wheel sensor(Saloon: drum brakes)
Rear wheel sensor(Estate: drum brakes)
Steering angle sensor
Gyrometer/accelerometer sensor
Toothed wheel7
5
12
13
4

Downloaded from www.Manualslib.com manuals search engine 459
ELECTRICAL
SYSTEM
STARTER MOTORS
Abbreviations and definitions
ALL TYPES
Coding of climates is as follows:
CLIMATES:C Hot
: Starting possible as low as 18°C.
T Temperate: Starting possible as low as 18°C.
F Cold: Starting possible as low as 25°C.
GF Very cold: Starting possible as low as 30°C.
Meaning of abbreviations:
BV
: Gearbox.
M: Manual gearbox.
A: Automatic gearbox.
MAP: Piloted manual gearbox.
DA: Powerassisted steering.
REFRI: Air conditioning.

Downloaded from www.Manualslib.com manuals search engine ALTERNATORS
Abbreviations and definitions
ALL TYPES
Coding of climates is as follows:
CLIMATES:
C
: Hot (45°C/37°C).
T: Temperate (37°C/17°C).
F: Cold (17°C/25°C).
GF : Very cold (<25°C).
Meaning of abbreviations:
BV
: Gearbox.BVM: Manual gearbox.BVA: Automatic gearbox.BVMP: Piloted manual gearbox.NON REFRI: Without air conditioning.REFRI: With air conditioning.DA: Powerassisted steering.GEP: Electropump motor.DP: Double lug.3 Pts: 3Point.NC: Not marketed.TT: All Types.N: Level.SOP: Without Option.TOP: All Options.L.C.: Heated rear screen.DAG:Left hand drive.DAD:Right hand drive.
472
ELECTRICAL
SYSTEM

Downloaded from www.Manualslib.com manuals search engine 473
ELECTRICAL
SYSTEM
ALTERNATORS
Allocation of alternator classes
C2
Meaning of abbreviations, see page:472.
Without aircon With aircon
Without cold pack With cold pack Without cold pack With cold pack
RT3
RT3RT3
RT3RT3
RT3RT3
RT3
Engine Gearbox Climate Base N1 or
N3Base N1 or
N3Base N1 or
N3Base N1 or
N3
N2 N2 N2 N2
C
8
88
81.1iT
BVM F77
77
7GF
C
791.4i T77 8BVMPF8778GF88C791.6i 16V T77 8BVMF8778GF88C
1.4 HDiT15BVM F
GF