Steering pivot Citroen C3 2004 1.G User Guide

Downloaded from www.Manualslib.com manuals search engine 386
AXLES
SUSPENSION
STEERING
FRONT AXLE
Evolution: Suspension arm balljoint
XSARA
Application from RPO: 7968.
New components:
Suspension arm balljoint.
Pivot.
Old fitting
ØA = 16 mm.
New fittingØA = 18 mm.
Repair requirements.
ESSENTIAL:Swapping of old and new components is forbidden.
It is permitted to fit a new pivot/balljoint assembly on one side of an old
vehicle.
Replacement Parts.
The old components are still available from Replacement Parts.
B3CP054D

Downloaded from www.Manualslib.com manuals search engine 388
AXLES
SUSPENSION
STEERING
FRONT AXLE
XSARA
Pivot balljoint:
Manual steering, groove at «b».
Power steering, groove at
«b».
Tongue «a» towards the front.
B3CP049C
B3CP043D

Downloaded from www.Manualslib.com manuals search engine 394
AXLES
SUSPENSION
STEERING
XSARAMANUAL STEERING SPECIFICATIONS
Manual steering
Tightening torques (m.daN).
(7)
Pivot balljoint nut:4
(8)
Link rod lock nut: 4.5
(9)
Balljoint on steering rack:6
(10)
Fixing on cradle:5
(11)
Plunger flange screw: 1.2
B3EP042D

Downloaded from www.Manualslib.com manuals search engine 395
AXLES
SUSPENSION
STEERING
22/1 Steering ratio
MANUAL STEERING SPECIFICATIONSXSARA
Manual steering (continued)
Number of teeth
Pinion Steering rack
travel
(mm)
73,56 teeth
(RH helix)29(13)
Yellow thicknessmm4,3
Left hand driveSteering rackSteering stop
colour codeNumber
of steering
wheel turns
Length of the steering track rods (Preadjustment)= 371mm (Between balljoint centres)or391mm (Between the centre of the pivot balljoint and the contact face of the steering rack balljoint).

Downloaded from www.Manualslib.com manuals search engine 397
AXLES
SUSPENSION
STEERING
POWERASSISTED STEERING SPECIFICATIONS
Powerassisted steering
XSARA
Tightening torques (m.daN).
(7)
Pivot balljoint nut:4
(8)
Link rod lock nut: 4.5
(9)
Balljoint on steering rack:6
(10)
Fixing on subframe:5
(11)
Hydraulic pipe connection: 2.5
(12)
Valve to housing fixing: 1.2
(13)
Plunger flange screw: 1.2
(14)
Screw fixing the steering ram
to the housing: 5.5
(15)
Nut fixing the steering ram
to the yoke: 5.5
B3EP08RD

Downloaded from www.Manualslib.com manuals search engine 398
AXLES
SUSPENSION
STEERING
POWERASSISTED STEERING SPECIFICATIONS
XSARA
Powerassisted steering (Continued)
Number of teeth
Pignon Steering rack
travel
(mm)
71,7(
*)
(RH helix)
28
Protector colour Vehicles
BLACKAll Types (except 1.6i 16V 1.9 TD)7
Steering valve
Number of teeth (*) 3,3
LHDSteering rackNumber of
steering wheel
turns
Length of the steering link rods (Preadjustment)= 371mm (Between balljoint centres)or391mm (Between the centre of the pivot balljoint and the contact face of the steering rack balljoint).
1.6i 16V 1.9 TDORANGE8
18,8/1 Steering
ratio

Downloaded from www.Manualslib.com manuals search engine 402
AXLES
SUSPENSION
STEERING
A > B =Negative figure: – = TOEOUT
A < B = Positive figure:+ =TOEIN
WARNING
AXLE GEOMETRY
Checks at reference height (the reference height of the vehicle is set as per the table below).
NO CRD Vehicle (CRD = Difficult road conditions)
Front axle Rear axle
Vehicle Tracking Castor Pivot angle Camber Tracking Camber
Adjustable Yes No
All types0 ± 1 mm4,8 ± 1,3 mm
0°09’ at + 0°09’3° ± 18’ 10°43’ ± 30’ 0° ± 30’
0°43’ ± 0°12’ 1°13’ ± 18’
XSARA PICASSO
B3CP02UC

Downloaded from www.Manualslib.com manuals search engine 404
AXLES
SUSPENSION
STEERING
A > B =Negative figure: – = TOEOUT
A < B = Positive figure:+ =TOEIN
WARNING
AXLE GEOMETRY
Checks at reference height (the reference height of the vehicle is set as per the table below).
CRD Vehicle (CRD = Difficult road conditions)
Front axle Rear axle
Vehicle Tracking Castor Pivot angle Camber Tracking Camber
Adjustable Yes No
All types 1 ± 1 mm3,7 ± 1,3 mm
0°18’ at 0°0’2°56’ ± 18’ 10°25’ ± 30’ 0°07’ ± 30’
0°33’ ± 0°12’ 1°14’ ± 18’
XSARA PICASSO
B3CP02UC
Engines: NFV RFN RHY

Downloaded from www.Manualslib.com manuals search engine 405
AXLES
SUSPENSION
STEERING
FRONT AXLE
Tightening torques m.daN.
(1)Damper nut: 4.5 ± 0.4
(2)Cup screw: 2.5 ± 0.2
(3)Suspension leg(4)Antiroll bar link rod balljoint: 3.7 ± 0.3
(5)Suspension leg swivel: 4.5 ± 0.4
(6) Antiroll bar(7)Antiroll bar link rod balljoint: 3.7 ± 0.3
(8)Lower swivel balljoint: 4 ± 0.4.
(9) Hub nut (greased): 32.5 ± 2
(10)Wheel bolt (face and threads not greased):9 ±1
(11) Lower arm front pivot: 7.6 ± 0.7
(12)Lower arm rear pivot and
antiroll bar bearing:6.8 ±0.6
(13) Screw under rear pivot : 3.5 ± 0.3 Lower arm in forged steel : 3.7 ± 0,3 Lower arm in plate steel: 3.1 ± 0,3Screw fixing subframe on bodyshell:8.5 ±0,8Screw fixing balljoint on lower arm (plate steel):4.5 ± 0,4
Antiroll bar
Engine
All TypesDiameter
21colour reference
WHITE Suspension leg angle :
Tab «a»towards the front.B3CP056P
B3CP057D
B3CP043D
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 408
AXLES
SUSPENSION
STEERING
STEERING COLUMN SPECIFICATIONS
Tightening torques (m.daN).
(7)
Pivot balljoint nut: 4 ± 0.4
(8)
Steering rod adjusting lock nut: 4.5 ± 0.4
(9)
Balljoint on steering rack: 6 ± 0.6
(10)
Fixing steering on subframe: 8 ± 0.8
(11)
Hydraulic pipe connection: 2.4 ± 0.2
(12)
Power steering valve: 1.2 ± 0.2
(13)
Plunger flange screws: 1.2 ± 0.2
(14)
Steering ram screw on housing:9 ±1
(15)
Steering ram screw on yoke:9 ±1
NOTE:
When removing the steering, it is imperative to replace screws
(14)and (15)(new screws).
B3EP117D
XSARA PICASSO