connecting rod Citroen C3 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 89
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
CYLINDER HEAD (mm)
Engine types KFW NFV NFU
Maximum permissible bow0,05
Gasket surface regrinding 0,20
TIGHTENING TORQUES (m.daN)
Crankshaft bearing Pretightening 2 ± 0,2 2 ± 0,2
screws Angular tighten 45° 50° ± 5°
Connecting rod screwsTightening3,8 ±0,4
Flywheel screw Tightening 6,5 ± 0,7
Crankshaft pinion screw Pretightening
Angular tighten10 ±1
Camshaft pulley screw Pretightening
Angular tighten 8 ± 0,8
Camshaft hubs 8 ± 0,8
Camshaft hub screwTightening1 ± 0,1
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 90
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
CYLINDER HEAD (mm)
Engine types 6FZ RFN RFS WJY RHY RHZ
Maximum permissible bow 0,05 0,03
Gasket surface regrinding 0,30 0,20 0,40
TIGHTENING TORQUES ( m.daN)
Pretightening (1) Ø 11 : 1 ± 0,1 2 ± 0,1 2,5 ± 0,3
(2) Ø 6 : 1 ± 0,1
Slackening Ø 11 (only)
Tightening Ø 11 to 1 ± 0,1 8,5 ± 0,8 7 ± 0,7
Crankshaft then to 2 ± 0,1
bearing screws Tightening Angular Ø 11 at 70° ± 5° 60° ± 6° 60° ± 6°
Tightening Ø 6 to 1 ± 0,1
Pretightening 1 ± 0,1 4 ± 0,4 2 ± 0,2
ConnectingSlackening 180° (1/2 turn)
rod screws Tightening 2,3 ± 0,2 2,3 ± 0,2 2± 0,2
Angular tightening46°±5°46° ±4,6° 70° ± 7° 70° ± 7°
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 308
RECOMMENDATIONS PRECAUTIONS: MA PILOTED MANUAL GEARBOX
Safety requirements.
ESSENTIAL:Given the special features of the MA type piloted
manual gearbox, observe the requirements detailed below.
IMPERATIVE: Always disconnect the battery negative terminal
before operating on the actuators.
NOTE:
After disconnecting the battery, never try to remove the clutch
actuator on the vehicle before having checked that it is in the closed
position
(rod pushed in).
IMPERATIVE:After Sales checks done with the engine running must be
performed with «Neutral»engaged and the handbrake on (unless there
is a clear mention otherwise in the repair procedures).
IMPERATIVE:The areas of movement of the clutch fork and of the gear
engagement lever must always be kept free during the actuatoroperating phases.
CLUTCH
GEARBOX
TRANSMISSION
IMPERATIVE:When initialising the clutch actuator and/or gearbox
actuator, do not allow any person to walk or stand in front of the vehicle.
WARNING:When the engine is running, it is forbidden to perform
repairs on the clutch and gearbox actuators on the vehicle (whether
manually or using a diagnostic tool).
WARNING:Each time the driver’s door is opened and each time the
igntion is switched on, the gearbox ECU prompts the initialising of the
clutch and gearbox actuators
(there is movement of the clutch fork and
of the gear lever).
WARNING:Whether the ignition is switched on or not, an action on the
gear selector causes the clutch fork and the gear engagement lever to
move on the gearbox.
Engines: HFX KFV NFU 8HX
C2