plug Citroen C3 2004 1.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 30
GENERAL
CAPACITIES (in litres)
Draining mandhod.
The oil capacities are defined according to the following mandhods.
1/
Vehicle on level surface (in high position, if equipped with hydropneumatic suspension).
2/Engine warm (oil temperature 80°C).
3/ Draining of the oil sump + removal of the cartridge (duration of draining + dripping = 15 min).
4/Refit plug + cartridge.
5/ Engine filling.
6/Engine starting (allowing the cartridge to be filled).
7/ Engine stopped (stationary for 5 min).
ESSENTIAL: Systematically check the oil level using the oil dipstick.

Downloaded from www.Manualslib.com manuals search engine 69
ENGINE
SPECIAL FEATURES TIGHTENING TORQUES (m.daN )
EnginesHFX KFV NFU
Cylinder head
Coolant outlet housing
in plastic
0,8 ± 0,2
in aluminium0,8 ± 0,2
Camshaft bearing caps (TU1JPTU3JP)
Tightening
2 ±0,2
Angular tightening44 °± 4°
Camshaft bearing caps (TU5JP4)
Tightening
2 ± 0,2
Angular tightening50°±5°
Inlet manifold0,8 ± 0,2
Exhaust manifold1,8 ±0,4
Valve rockers adjusting screw1,75 ± 0,25
Sparking plugs3
Camshaft pulley screw (TU1JPTU3JP)3,7 ± 0,2
Camshaft pulley screw (TU5JP4)4,5 ± 0,5
C2

Downloaded from www.Manualslib.com manuals search engine 76
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Crankshaft
Engine types HFX KFV NFU
Accessories drive pulley0,8 ± 0,2
Pinion fixing on crankshaft10 ± 1 2,5 ± 0,2
Cylinder block
Sump0,8 ± 0,2
Timing belt tensioner roller2 ± 0,2 2,2 ± 0,2
Accessories belt tensioner roller2 ± 0,2 2,5 ± 0,2
Alternator support fixing1,7 ±0,3
Alternator fixing on support3,7 ± 0,3
Cylinder head
Coolant outlet housing0,8 ± 0,2
Camshaft bearing cap
Tightening
2 ± 0,2 2 ± 0,2
Angular tightening44°±4°50° ± 5°
0,8 ± 0,2
Exhaust manifold1,7 ± 0,3 2 ± 0,2
Valve rockers adjusting screw1,75 ±0,25
Sparking plugs2,75 ± 0,25
Camshaft pulley screw8 ± 0,8
C3

Downloaded from www.Manualslib.com manuals search engine 80
ENGINESPECIAL FEATURES TIGHTENING TORQUES (m.daN )
Cylinder head
Exhaust manifold1,8 ± 0,2
Sparking plugs2,2 ± 0,2
VVT pulley cap4 ± 0,4
VVT control electrovalve0,8 ± 0,2
VVT inlet camshaft pulley screw
Pretightening
2 ± 0,2
Tightening6,1 ± 0,6
Exhaust camshaft pulley screw4,5 ± 0,4
Flywheel / Clutch
Engine flywheel6,7 ±0,6 (coat the screws with LOCTITE FRENETANCH)
Clutch mechanism2 ± 0,2
Lubrication circuit
Oil pressure switch2 ± 0,2
Oil pump0,9 ± 0,1
Cooling circuit
Coolant pump1 ± 0,1
Coolant outlet housing0,8 ± 0,1
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
149
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
B1BP2MAC
Checking the timing (continued).
Engine:
NFU.
Place a jack under the engine, peg the engine.
Remove:
The engine support
(4)complete.
The timing casing
(3).
The sparking plugs
(eases engine rotation).
Turn the wheel to rotate the engine
(normal direction of rotation).
Position the pegs
[3a]and[3b].
Peg the flywheel, using tool
[1].
If the setting is not correct, recommence the operation.
Remove the tools
[1], [2], [3a]and [3b].
Complete the refitting.
B1BP2MBCB1EP18MC
C2 C3 C3 PLURIEL

Downloaded from www.Manualslib.com manuals search engine 158
ENGINE
Tools.
[1]
Flywheel peg: 4507T.A
[2]Camshaft pulley peg: 4507T.B Tool kit 4507T
[3]Square: 4507T.J
[4]Belt tension measuring instrument:4122T
[5]Valve rocker thrust plate :4533T.Z
Checking the timing.
Peg the flywheel, using tool [1].
Peg the camshaft pulley, using tool [2].
Setting the timing.
NOTE:
Remove the sparking plugs, to ease rotation of the crankshaft.
Rotate the engine by means of the crankshaft screw (1).
Peg the camshaft pinion.
Peg the flywheel
Slacken the nut
(2).
Fullt detension the belt by acting on the tensioner roller.
Remove the belt.
IMPERATIVE: Check that the tensioner roller turns freely (no tight spot).
CHECKING AND SETTING THE VALVE TIMING
Engines: KFW NFV

B1EP067CB1EP066CB1EP068C
XSARA XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine ENGINE
165
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Tools.
[1]
Flywheel peg :4507T
[2]Camshaft peg: 4533TA.C1
[3]Crankshaft setting peg: ().0194.A
Checks.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.Remove:
The oil filter. The engine cover.
The upper timing cover
(1).
The sparking plugs, to ease rotation of the engine.
Rotate the engine by means of the crankshaft screw
(never turn the engine backwards).
B1BP2ZJD
C3

Downloaded from www.Manualslib.com manuals search engine ENGINE
201
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1BP304D
Tools.
[1]
Flywheel setting peg: ().0194.C
[2]
Camshaft setting peg:().0194.B
[3]
Crankshaft setting peg: ().0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove: The front RH wheel.
The front RH splashshield.
The accessories drive belt
(see corresponding operation).
Uncouple: The fuel supply unions
(1).
The air/air heat exchanger inlet and outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connecter at
«a».
Remove and move aside the power steering fluid reservoir
(6).
Uncouple, plug and move aside the tube
(2).
Support the engine with a roller jack equipped with a block.
Remove the engine supports
(4)and (5).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 205
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ 9HY
B1BP304D
Tools.
[1]
Flywheel setting peg: ().0194.C
[2]
Camshaft setting peg:().0194.B
[3]
Crankshaft setting peg: ().0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove: The front RH wheel.
The front RH splashshield.
The accessories drive belt
(see corresponding operation).
Uncouple:
The fuel supply unions
(1).
The air/air heat exchanger inlet and outlet pipes
(3).
The exhaust line
(at the flexible pipe).
Disconnect the connecter at
«a».
Remove and move aside the power steering fluid reservoir
(6).
Uncouple, plug and move aside the tube
(2).
Support the engine with a roller jack equipped with a block.Remove the engine supports
(4)and (5).
XSARA PICASSO

Downloaded from www.Manualslib.com manuals search engine 212
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: WJY
B1BP2FTC
Setting the timing.
Removing.
Disconnect the battery.
Remove the front RH lower splashshield, using tool [1].
Remove the accessories drive belt (see corresponding operation).
Uncouple and plug the diesel fuel delivery and return hoses. Support the engine, using a workshop hoist.
Remove the RH engine support.
Engage 5th gear to permit rotation of the engine. Remove the upper cover
(1).
Remove the intermediate cover (2).
Remove the lower cover (3).
WARNING:Refit the screw (4)equipped with a washer (5 mm thick).
Rotate the front RH wheel to drive the engine in its normal direction of
rotation. Bring the camshaft drive and injection pump pinions to their setting points.
Position the peg
[2](from underneath the vehicle).
Continue turning the engine until the peg [2]engages in the flywheel.
B1BP30BC
XSARA