lock Citroen C3 2013 2.G Owner's Guide

4
Access
75











Boot
)After unlocking the vehicle using theremote control or the key, pull the handleand raise the tailgate.
)
Lower the tailgate using the interior grab
handle.
-when the engine is running, this
warning lamp comes on, accompanied
b
y a message on the multifunctionscreen for a few seconds,
Tailgate release
Unlocking
)
Fold back the rear benchseat to gainaccess to the lock from inside the boot.)
Insert a small screwdriver into hole Aof thelock to unlock the tailgate.

I
f the tailgate is not closed correctly:

Opening Closing
-when the vehicle is moving
(speed above6 mph (10 km/h)), this warning lamp comes
on, accompanied by an audible signal and
a messa
ge on the multifunction screen for a few seconds.
System for mechanical unlocking of the boot
in the event of a battery or central locking
malfunction.

Access
76


























Fuel tank
Low fuel level

When the fuel tank minimum level is
reached this warning lamp comes on on the instrument panel. When it first comes on there remains approximately5 litres
of fuel in the tank.
Filling
A label affixed to the inside of the flap remindsyou of the type of fuel to be used depending onyour engine.
Additions of fuel must be of at least 7 litres, in
order to be registered by the fuel gauge. To
fill the tank safely: )the engine must be switched off,)
open the fuel filler flap,
)
inser t the key in the cap, then turn it to the left,
)
remove the cap and hook it onto the clip located on the inside of the flap,)
fill the tank, but do not continue after the3rd cut- off of the pump; this could cause
malfunctions.
When
you have filled the tank: )
put the cap back in place, )
turn the key to the right, then remove itfrom the cap, )
close the flap.
You must refuel as soon as possible to avoid
running out of fuel.
If you run out of fuel (Diesel), refer also to the
"Checks" section. Fuel tank capacity: approximately
50 litres (petrol) or 46 litres (Diesel) or 37 litres (LPG); (Depending on version:
approximately 30 litres (petrol or Diesel)).
With Stop & Star t, never refuel with the system in STOP mode; you must switch off the ignition with the key.

The key cannot be removed from thelock until the cap is refitted. Opening the filler cap may create anoise caused by an inrush of air. This vacuum is entirely normal, resulting from the sealing of the fuel system.

5
Visibility
87
Version with Zenith windscreen
1.Rear side reading lamps
2.Rear cour tesy lamp
Central or rear courtesy lamps

Version without Zenith windscreen
A.Central courtesy lamp


Front side reading lamps
)
With the ignition on, the first press of thecorresponding switch switches on the
reading lamp concerned in permanent
lighting mode. ) Following a second press, it comes on:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when a door is opened,
- when the remote control locking button
is pressed, in order to locate your
v
ehicle. In this position, the courtes
y lamp
comes on gradually:
- when the vehicle is unlocked,
- when the ke
y is removed from the ignition,
- when a door is opened,
- when the remote control lockin
g button is
activated, in order to locate your vehicle.
It switches o
ff gradually:
- when the vehicle is locked,
- when the ignition is switched on,
-
30 seconds after the last door is closed.
Permanentl
y off.

Permanent lighting.
It switches o
ff gradually:


- when the vehicle is locked,

- when the i
gnition is switched on,

- 30 seconds after the last door is closed.
To switch o
ff the rear cour tesy lamp, place it in
the "permanently off" position.









Courtesy lamps Selection and control of the various passenger compartment lamps.

In permanent lighting mode, the lighting durationvaries, according to the circumstances:-with the ignition off, approximately ten minutes,-in energy economy mode, approximately thirty seconds,
-with the engine running, unlimited.

Child safety
100
As a safety precaution, do not leave:


- a child or children alone andunsuper vised in a vehicle,

- a child or an animal in a vehicle which is exposed to the sun, with the windowsclosed,

- the keys within reach of children insidethe vehicle.
To prevent accidental opening of the doors and rear windows, use the "Child lock".
Take care not to open the rear windows bymore than one third.
To protect young children from the rays of the sun, fit side blinds on the rear windows.
For optimum installation of the "forwards-facing" child seat, ensure that the back of thechild seat is in contact with the back of thevehicle's seat and remove the head restraint. Ensure that the head restraint is stored or attached securely to prevent it from beingthrown around the vehicle in the event of sharp braking. Refit it if an adult uses the seating position.Children under the age of 10 must not travelin the "for wards-facing" position on the front passenger seat, unless the rear seats are already occupied by other children, cannotbe used or are absent. Deactivate the passenger airbag when a "rearwards-facing" child seat is installed on the front seat. Other wise, the child would risk beingseriously injured or killed if the airbag were to inflate.


Installing a booster seat

The chest par t of the seat belt must be
positioned on the child's shoulder without touching the neck.
Ensure that the lap part of the seat belt passes correctly over the child's thighs.
CITROËN recommends the use of a booster seat which has a back, fitted with a seat belt guide at shoulder level.
The incorrect installation of a child seat in a vehicle compromises the child's protection inthe event of an accident.Ensure that there is no seat belt or seat belt buckle under the child seat, as this could destabilise it. Remember to fasten the seat belts or the child seat harnesses keeping the slackrelative to the child's body to a minimum,even for short journeys.When installing a child seat using the seatbelt, ensure that the seat belt is tightened correctly on the child seat and that it securesthe child seat firmly on the seat of your vehicle. If your passenger seat is adjustable,move it for wards if necessary. At rear seating positions, always leave sufficient space between the front seat and: - a "rear wards facing" child seat, - the child's feet for a child seat fitted "forwards facing". To do this, move the front seat for wardsand, if necessary, move its backrest into the upright position.





Advice on child seats

Child safety
104








Manual child lock
Locking
)With the ignition key, turn the red control
one quarter of a turn:
- to the right on the le
ft-hand rear door,
- to the left on the right-hand rear door.


Unlocking
)With the ignition key, turn the red control
one quar ter of a turn:
- to the left on the left-hand rear door,
- to the ri
ght on the right-hand rear door.




Electric child lock

Activation
)
Press this button. The indicator lamp on the button comes on, accompanied by a message in the multifunction screen.
This indicator lamp remains on until the childlock is deactivated.


Deactivation
)Press the button again.
The indicator lamp on the button switches off,
accompanied by a message in the multifunction screen. This indicator lamp remains off until the childlock is activated.

This system is independent and in nocircumstances does it take the place of the central locking control. Check the status of the child lock eachtime you switch on the ignition.

Always remove the key from the ignition when leaving the vehicle, even for a short time. Remote control system to prevent opening o
f
the rear doors using their interior controls and use of the rear electric windows.
The control is located on the driver's door, with
th
e electric window controls. Mechanical system to prevent opening o
f the rear door using its interior control.
The control is located on the edge of each rear door.

8
Safety
107
Operating fault
You must stop as soon as it is safe to do so.
In either case, contact a CITROËN dealer or aqualified workshop. If this warnin
g lamp comes on,
accompanied b
y an audible signal
and a message in the screen, it
indicates a malfunction of the anti-lock braking system which couldresult in loss of control of the vehicle
when braking.
If this warnin
g lamp comes on,
together with the STOPand ABSwarning lamps, accompanied by an
audible signal and a message in the screen, it indicates a malfunction of
the electronic brake force distribution
which could result in loss of control of
the vehicle when braking.
Emergency braking assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure more quickly, thus reducing the stopping distance.

Activation

It is triggered by the speed at which the brake
pedal is pressed.
Th
e effect of this is a reduction in theresistance of the pedal and an increase in
braking efficiency.
When replacing wheels (tyres andrims), ensure that they conform to the manufacturer's recommendations.
When braking in an emergency, press firmly without releasing the pressure.
















Braking assistance systems


Anti-lock braking system
and electronic brake force
distribution

Linked systems which improve the stability andmanoeuvrability of your vehicle when braking,
in par ticular on poor or slippery surfaces.

Activation

The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself felt by slight vibration of the brake pedal.

When braking in an emergency, press very firmly without releasing thepressure. Group of supplementar
y systems which helpyou to obtain optimum braking in completesafety in emergency situations:


- anti-lock braking system (ABS),

- electronic brake force distribution (EBFD),

- emergency braking assistance (EBA).

Safety
110
The driver must ensure that passengers usethe seat belts correctly and that they are allrestrained securely before setting off. Wherever you are seated in the vehicle, always fasten your seat belt, even for shor t
journeys.
Do not interchange the seat belt buckles as they will not fulfil their role fully.
The seat belts are fitted with an inertia reel permitting automatic adjustment of the lengthof the strap to your size. The seat belt isstowed automatically when not in use.
Before and after use, ensure that the seatbelt is reeled in correctly.
The lower part of the strap must be positioned as low as possible on the pelvis.
The upper par t must be positioned in the hollow of the shoulder.
The inertia reels are fitted with an automatic locking device which comes into operation inthe event of a collision, emergency braking or if the vehicle rolls over. You can release the device by pulling firmly on the strap and releasing it so that it reels in slightly.


Recommendations for children

Use a suitable child seat if the passenger is less than 12 years old or shor ter than one and a half metres.
Never use the same seat belt to secure more than one person.
Never allow a child to travel on your lap.
In order to be effective, a seat belt must:- be tightened as close to the body aspossible, - be pulled in front of you with a smoothmovement, checking that it does not
twist, - be used to restrain only one person,- not bear any trace of cuts or fraying,- not be converted or modified to avoid affecting its performance.
In accordance with current safety regulations, for all repairs on your vehicle,go to a qualified workshop with the skills andequipment needed, which a CITROËN dealer is able to provide. Have your seat belts checked regularly bya CITROËN dealer or a qualified workshop,particularly if the straps show signs of damage.Clean the seat belt straps with soapy water or a textile cleaning product, sold byCITROËN dealers.
After folding or moving a seat or rear bench seat, ensure that the seat belt is positionedand reeled in correctly.


In the event of an impact
Depending on the nature and seriousnessof the impact
, the pretensioning device may be deployed before and independently of the airbags. Deployment of the pretensionersis accompanied by a slight discharge of harmless smoke and a noise, due to theactivation of the pyrotechnic cartridge incorporated in the system.
In all cases, the airbag warning lamp comes on.
Following an impact, have the seat beltssystem checked, and if necessary replaced, by a CITROËN dealer or a qualified workshop.

9
Driving
123

Manual operation
)Select position M
for sequential
changing
of the four gears. )Push the lever towards the + sign to change up a gear.)Pull the lever towards the -
sign to changedown a gear.
It is onl
y possible to change from one gear to
another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears
engaged appear in succession in theinstrument panel.
Invalid value during manual
operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).

Stopping the vehicle
Before switching off the engine, you can engageposition Por Nto place the gearbox in neutral. In both cases, apply the parking brake to immobilise the vehicle.


Operating fault
When the ignition is on, the lighting
of this warning lamp, accompaniedby an audible signal and a message in the
multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto R
and from N
to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.
To r e d u c e fuel consumption when at a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.



There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the Pposition to another position when the battery is flat.
If the lever is not in position P, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P
; the
message disappears.

If the en
gine speed is too low or too high, the gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving
very slowly, the gearbox selects gear M1automatically.
The spor t and snow programmes do not
operate in manual mode.

Driving
132





Rear parking sensors


Activation
This detects any obstacle (person, vehicle,
tree, gate, etc.) behind the vehicle, except
obstacles located just below the bumper. The s
ystem is activated as soon as reversegear is engaged, accompanied by an audible
signal. The proximity information is given by:


- an audible signal, which becomes more
rapid as the vehicle approaches the
obstacle.

- a graphic (according to version) in the
multi
function screen, with blocks whichbecome increasingly closer to the vehicle.

On completion of the manoeuvre, when you exit
reverse gear, the system becomes inactive.
An object, such as a stake, a roadworks cone or any other similar object may be detected at the beginning of themanoeuvre, but may no longer be detected when the vehicle comes close to it.


The parking sensor system cannot, inany circumstances, take the place of the vigilance and responsibility of thedriver. S
ystem consisting of four proximity sensors,
located in the rear bumper.
Wh
en the distance between the rear of the
vehicle and the obstacle is less than thir ty centimetres, the audible signal becomes continuous and the "Danger" symbol appears
in the multifunction screen.

Checks
142
According to your version of instrument panel, the start of
saturation of the par ticle emissions filter is indicated by:

- fixed illumination of the par ticleemissions filter warning lamp,
accompanied by an audible signal, or

- temporary illumination of
the ser vice warning lamp,

As soon as the traffic conditions permit, regenerate
the filter by driving at a speed of at least 40 mph (60 km/h) until the warning lamp goes off.
If the warning lamp stays on, refer to the "Additivelevel" section.







Checks
12 V battery

The battery does not require anymaintenance.
However, check that the terminals
are clean and correctly tightened,
particularly in summer and winter.
The presence of this label, in particular with
the Stop & Star t s
ystem, indicates the use of a specific 12 V lead-acid battery with special
technology and specification. The involvement
of a CITROËN dealer or a qualified workshop isessential when replacing or disconnecting the battery. When carr
ying out work on the battery, refer
to the "12 V battery" section for details of theprecautions to be taken before disconnecting
the battery and following its reconnection. Unless other wise indicated, check these components in accordance with the MAINTENANCE AND WARR ANT Y GUIDE and accordin
g to your engine.
Other wise, have them checked by a CITROËN dealer or a qualified workshop.
On a new vehicle, the first operations of regeneration of the par ticle emissions filter may be accompanied by the smellof "burning", which is per fectly normal. Following prolonged operation of the vehicle at very low speed or at idle, you may, in exceptional circumstances,notice the emission of water vapour at the exhaust on acceleration. This does not affect the behaviour of the vehicle or the environment.
Particle emission filter (Diesel)
accompanied by an audible signal and amessage that there is a risk of blockage of
the particle emissions filter.
Air filter and passenger compartment filter
Refer to the MAINTENANCE AND
WARR ANT Y GUIDE for details of
the replacement intervals for thesecomponents.
Depending on the environment (e.g. dusty
atmosphere) and the use of the vehicle (e.g. city
driving), replace them twice as often if necessar y.y A clogged passenger compar tment filter may have
an adverse effect on the performance of the air conditioning system and generate undesirableodours.

Replace the oil filter each time the
engine oil is changed.
Refer to the MAINTENANCE AND
WARR ANT Y GUIDE for details of
the replacement interval for thiscomponent.
Oil filter