turn signal Citroen C3 2013 2.G Owner's Manual

1
Monitoring
33
Airbags

temporarily. This lamp comes on for a fewseconds when you turn on the
ignition, then goes off. This lamp should
go off when the engine is started.
If it does not go off, contact a CITROËN dealer or a qualified workshop.

fix
ed. One of the airbag or seat belt pretensioner systems has a fault. Have it checked by a CITROËN dealer or a qualified
workshop.
Seat belt not fastened / unfastened
fixed then flashingaccompanied by an
increasing audiblesignal.The driver and
/or the front passenger has not fastened or has unfastenedtheir seat belt.
Pull the strap then inser t the tongue in the buckle.
Door(s) open

fixed if the speed is
below 6 mph (10 km/h). A door or the boot is still open. Close the door or boot.

fixed and accompaniedby an audible signalif the speed is above6 mph (10 km/h).
Warning lampis onCauseAction / Observations

4
Access
67

Folding the key
)First press this button to fold the key.
If you do not press the button when foldingthe key, there is a risk of damage to themechanism.

Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip which has a special code. When the ignition is switched
on, this code must be recognised in order for
startin
g to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes after the ignition is switched off and prevents
starting of the engine by anyone who does not have the key.
In the event o
f a fault, you are
informed by illumination of this
warning lamp, an audible signal anda message in the screen.
Ignition switch


- Position 1: Stop

- Position 2: Ignition

- Position 3: Starting


Starting the vehicle
)
Inser t the key in the ignition switch.
The system recognises the star ting code.) Turn the key fully towards the dashboard toposition 3 (Starting).)
When the engine star ts, release the key.

Locating your vehicle
)
Press the closed padlock to locate your locked vehicle in acar park.
This is indicated b
y lighting of the cour tesylamps and flashing of the direction indicators for a few seconds. In this case,
your vehicle will not start; contact a CITROËN dealer as soon as possible.
Keep safely the label attached to the keys given
to you on acquisition of the vehicle.

Access
68
Remote control problem
Reinitialisation
)
Switch off the ignition. )
Turn the key to position 2 (Ignition on)
. )
Press the closed padlock immediately for a few seconds. )
Switch off the ignition and remove the key from the ignition switch.
The remote control is full
y operational again.


Changing the battery

Battery ref.: CR1620 / 3 volts.
If the batter
y is flat, you are informed by illumination of this warning lamp,
an audible signal and a message in
the multifunction screen.
)Unclip the casing using a coin at the notch. )Slide the flat battery out of its location.)Slide the new battery into its location
observing the original direction. )Clip the casing. )Reinitialise the remote control.


Switching the vehicle off


Key reminder

If the key is left in the ignition switch, an audible signal sounds when the driver's door is opened.

Do not attach any heavy objects to the key as this could weigh down on it when in the ignition switch and cause a fault. Followin
g disconnection of the vehicle battery,replacement of the remote control battery or
in the event of a remote control malfunction,you can no longer unlock, lock or locate your
v
ehicle. ) First of all, use the key in the lock to unlock or lock your vehicle.)
Then, reinitialise the remote control.
If the problem persists, contact a CITRO

Access
74
Emergency control

Locking the driver's door
)
Inser t the key in the lock, then turn it to the
right.
Unlocking the driver's door
)
Inser t the key in the lock, then turn it to theleft.


Locking the front and rear passenger doors
)Remove the black cap, located on the edge
of the door, using the key. )Insert the key in the socket, then turn it to
the stop.)Remove the key and refit the cap.



Unlocking the front and rear passenger doors
)Pull the interior door opening control.
In the event of failure of the centrallocking system, the battery must bedisconnected to lock the boot and so ensure that the vehicle is locked completely.
Check that the rear doors child lock is not on.
System allowing the doors to be locked andunlocked manually in the event of a fault with
the central locking system or a battery failure.
Activation
)Press button Afor more than two seconds.
A confirmation message appears on themultifunction screen, accompanied by an audible signal.
Deactivation
)Press button Aagain for more than
two seconds.
A confirmation message appears on themultifunction screen, accompanied by an audible signal.


Driving with the doors locked may make access more difficult for the emergency services in an emergency.

Visibility
82
Association with the automatic "Guide-me-home" lighting

Association with the automatic illumination of headlamps provides "guide-me-home" lighting
with the following additional options:


- selection of the lighting duration to 15, 30 or 60 seconds in the functions that can be set
in the vehicle configuration menu (except in
the case of the monochrome screen A, for
which the duration is set: 60 seconds),

- automatic activation of "guide-me-home"lighting when automatic illumination of headlamps is in operation.



Operating fault
In the event of a fault with the
sunshine sensor, the lighting
come on, this warning lamp is displayed in the
instrument panel and/or a message appears in
the screen, accompanied by an audible signal.
Contact a CITROËN dealer or a
qualified
workshop.
In fog or snow, the sunshine sensor may detect sufficient light. Therefore, thelighting will not come on automatically. Do not cover the sunshine sensor, coupled with the rain sensor andlocated in the centre of the windscreen behind the rear view mirror; the associated functions would no longer be controlled.

Automatic illumination of headlamps
Activation
)Turn ring to the "AUTO"
position. The automatic illumination of headlamps is accompanied by a message in the screen.

Deactivation
)Turn ring to a position other than "AUTO" . Deactivation is accompanied by a message in the screen.
The sidelamps and dipped beam headlamps
are switched on automatically, without any action on the par t of the driver, when a low level
of external light is detected or in certain cases
of activation of the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
off, the lamps are switched off automatically.

Driving
122
Moving off
)Apply the parking brake. )Select position Por N.)Star t the engine.
If this procedure is not followed, there is anaudible signal, accompanied by the display of an warning message.)With the engine running, press the brakepedal. )Release the parking brake. )Select position R, D
or M . )Gradually release the brake pedal.
The vehicle moves off immediately.

Automatic operation
)
Select position D
for automatic
changingof the four gears.
The gearbox then operates in auto-adaptive
mode, without any intervention on the par t
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
vehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal down
fully (kick down). The gearbox changes down
automatically or maintains the gear selecteduntil the maximum engine speed is reached.
On braking, the gearbox changes down
automatically to provide efficient engine braking.
If you release the accelerator sharply, the gearbox will not change to a higher gear for
safety reasons.

Sport and snow programmes

These two special programmes supplement the
automatic operation in very specific conditions of use.

Sport programme "S"
)Press button "S"
, after star ting the engine.
The gearbox automatically favours a dynamicstyle of driving.


Snow programme "7"
)Press button "7", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.

Return to automatic
o
peration
)At any time, press the button selectedagain to quit the programme engaged and
return to auto-adaptive mode.

S
appears in the instrument panel.
7
appears in the instrument panel.

Never select position N
while the vehicle is moving.Never select positions P
or Runless the vehicle is completely stationary.



If position N
is selected inadver tentlywhile driving, allow the engine toreturn to idle then select position Dto accelerate.


When the engine is running at idle, with the brakes released, if position R , D
or M
is selected, the vehicle moves evenwithout the accelerator being pressed. When the engine is running, never leave children in the vehicle without supervision.
When carrying out maintenance with the engine running, apply the parkingbrake and select position P.P

9
Driving
123

Manual operation
)Select position M
for sequential
changing
of the four gears. )Push the lever towards the + sign to change up a gear.)Pull the lever towards the -
sign to changedown a gear.
It is onl
y possible to change from one gear to
another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears
engaged appear in succession in theinstrument panel.
Invalid value during manual
operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).

Stopping the vehicle
Before switching off the engine, you can engageposition Por Nto place the gearbox in neutral. In both cases, apply the parking brake to immobilise the vehicle.


Operating fault
When the ignition is on, the lighting
of this warning lamp, accompaniedby an audible signal and a message in the
multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto R
and from N
to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.
To r e d u c e fuel consumption when at a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.



There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the Pposition to another position when the battery is flat.
If the lever is not in position P, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P
; the
message disappears.

If the en
gine speed is too low or too high, the gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving
very slowly, the gearbox selects gear M1automatically.
The spor t and snow programmes do not
operate in manual mode.

10
Checks
141
Additive level (Diesel with
particle emissions filter
)
According to your version of instrument panel,
the additive reser voir low level is indicated by:
To p p i ng up
The reser voir must be topped up without delay
by a CITROËN dealer or a qualified workshop.









Used products



- fixed illumination of the particleemissions filter warning lamp,
accompanied by an audible signal, or
- fix
ed illumination of the servicewarning lamp, accompanied byan audible signal and a message
that the par ticle emissions filter additive level is too low.

Do not discard used oil or fluids into sewers or onto the ground.
Take used oil to a CITROËN dealer or a qualified workshop (France) or to anauthorised waste disposal site.

Avoid prolonged contact of used oil or fluids with the skin.

Most of these fluids are harmful tohealth or indeed very corrosive.
Coolant level

The coolant level should be close
to the "MA X" mark but should never exceed it.
When the en
gine is warm, the temperature of
the coolant is regulated by the fan.

Changing the coolant
The coolant does not have to be changed.


Fluid specifi cation

The coolant must conform to themanufacturer's recommendations.
Top up the level when necessary.
The cooling fan may star t after switching off the engine: take care with ar ticles and clothing that might become caught by the fan blades.
In addition, as the cooling system is pressurised,
wait at least one hour after switching off theengine before carrying out any work.
To avoid any risk of scalding, unscrew the cap
by two turns to allow the pressure to drop. When
the pressure has dropped, remove the cap and
top up t
he level.
Screenwash fluid level
Fluid specifi cation
For optimum cleaning and to avoid freezing,
this
fluid must not be topped up or replaced with plain water.