service reset CITROEN C3 2023 Owners Manual

58
In the event of a breakdown
the booster (or to an earth point on the assisting
vehicle).
►
Connect the other end of the green or black
cable to the earth point


C
on the broken down
vehicle.
►

Start the engine on the assisting vehicle and
leave it running for a few minutes.
►


Operate the starter on the broken down
vehicle and let the engine run.
If the engine does not start immediately

, switch
off the ignition and wait a few moments before
trying again.
►

W
ait for it to return to idle.
►

Disconnect the jump leads in reverse order:
first remove (-) terminal then (+) terminal..
►


Refit the cover to the (+) terminal, if the
vehicle has one.
►


Allow the engine to run for at least
30

minutes, with the vehicle stationary, so that
the battery reaches an adequate state of charge.
Driving immediately without having
reached a sufficient level of charge may
affect some of the vehicle's functionalities.
Disconnecting/removing the
battery
In order to maintain an adequate state of charge
for starting the engine, it is recommended that
the battery be disconnected if the vehicle is
taken out of service for a long period.
Before disconnecting the battery: ►

Close all openings (doors, boot, windows).
►

Switch off all electrical consumers (audio
system, wipers, lighting, etc.).
►

Switch off the ignition and wait for 4
minutes.


Naturally Aspirated engine version

Turbo engine version
►
Disconnect the negative cable.
►

Disconnect the positive cable.
► Remove the mounting bracket if you need to
remove the battery .
Be careful not to cause accidental short
circuits between the positive and
negative battery terminals.
Do not allow smoking, sparks or flames
around fuel or the battery.
After reconnection
After reconnecting the battery, turn on the
ignition and wait 1 minute before starting the
engine, to enable the electronic systems to
initialise.
If minor problems nevertheless persist following
this operation, contact a CITROËN dealer.
Referring to the relevant section, initialise or
reset certain equipment:
–

Date and time.
–


Preset radio stations.
Towing the vehicle
General recommendations
Observe the legislation in force in the
country where you are driving.
Ensure that the weight of the towing vehicle is
higher than that of the towed vehicle.
The driver must remain at the wheel of the
towed vehicle and must have a valid driving
licence.

64
10" Touch Screen
Settings
Access the settings (system, phone, audio etc.).
Radio

Choosing the band
Press FM or AM on the bottom of the screen to
select the band.
Selecting a station
Make a short press to perform a manual
search for previous/next radio frequency.
Make a long press to perform an automatic
search for previous/next radio frequency.
Presetting a station
12 stations can be preset on the FM band and 6
on the AM band.
Manual
Make a long press on one of the preset number
to preset the current playing station.
Automatic
Press AST to search all frequencies within
the current band and automatically store valid
stations.
Phone

A phone must be paired to the system to be able to use the following
functionalities.
Pairing a phone
The services available depend on the network, the SIM card and the
compatibility of the Bluetooth
® devices used.
Consult the phone user guide, the service
provider and the OEM portal to check which
services are available.
https://citroen.in/citroen-connectivity
The Bluetooth
® function must be activated and
the phone in "Visible to all" mode.
To complete the pairing, whichever procedure
is used (from the phone or from the system),
ensure that the code is the same in the system
and in the phone.
If the pairing procedure fails, we
recommend deactivating and then
reactivating the Bluetooth
® function on the
phone and deleting any CITROËN name
present in the pairing list.
Procedure from the phone
The system discoverable mode will operate 90
seconds once the BT visibility option is selected
under Settings.
Select the name of the system in the list of
detected devices on the phone.
In the system, accept the connection request
from the phone and follow the instructions on the
phone and system screen.
Procedure from the system
Select Settings menu.
Select Phone.
Press Add device.
Press Scan for Devices .
The list of detected devices is displayed.
Select the name of the required phone in the list.
Depending on the type of phone, you
may by prompted to accept the transfer
of contacts.