remove seats Citroen C3 PICASSO DAG 2009.5 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2009.5, Model line: C3 PICASSO DAG, Model: Citroen C3 PICASSO DAG 2009.5 1.GPages: 200, PDF Size: 9.96 MB
Page 37 of 200
!
50
COMFORT
Press the control located under the
front end of the armrest to release it.
Move it to the low position.
Raise it notch by notch to reach the
desired position.
To place the armrest in the vertical posi-
tion, raise it and push it backwards be-
yond the point of resistance.
H e a d r e s t r a i n t h e i g h t a d j u s t m e n t
To raise the head restraint, pull it up-
wards.
To remove the head restraint, press
the lug A and pull the head restraint
upwards.
To put the head restraint back in
place, engage the head restraint
stems in the openings keeping them
in line with the seat back.
To lower the head restraint, press
the lug A and the head restraint at
the same time. T h e h e a d r e s t r a i n t i s fi t t e d w i t h a
frame with notches which prevents
it from lowering; this is a safety de-
vice in case of impact.
T h e a d j u s t m e n t i s c o r r e c t w h e n
t h e u p p e r e d g e o f t h e h e a d r e -
s t r a i n t i s l e v e l w i t h t h e t o p o f t h e
h e a d .
Never drive with the head restraints
removed; they must be in place and
adjusted correctly.
A d j u s t i n g t h e a r m r e s t
A d d i t i o n a l a d j u s t m e n t s
H e a t e d s e a t s c o n t r o l
Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating re-
quired:
0 : Off.
1 : Low.
2 : Medium.
3 : High.
With the engine running, the front seats
can be heated separately.
Page 40 of 200
i
i
i
52
COMFORT F u l l y - f o l d e d p o s i t i o n F l a p s b e h i n d t h e r e a r s e a t s
Move the corresponding front seat
forward if necessary.
Place the head restraints in the low
position.
Pull control A , to release the seat
back which folds easily onto the
seat cushion.
This manoeuvre automatically re- tracts the seat cushion.
T h e s e a t fi t s i n t o t h e fl o o r , p r o v i d i n g a
c o n t i n u o u s l e v e l fl o o r .
To put the seat back in position:
Pull the seat back backwards until it
locks in place.
Return the seat cushion to the de-
sired position. Flaps
B fi t t e d t o t h e b a c k o f t h e r e a r
s e a t c l o s e t h e b o o t fl o o r w h e n t h e r e a r
seats are in the forward position.
P u l l o n t h e u p p e r s e c t i o n o f t h e fl a p s t o
release them.
They then provide a continuous level
fl o o r .
A d j u s t i n g t h e h e a d r e s t r a i n t s
T h e 1 / 3 - 2 / 3 r e a r s e a t i s fi t t e d w i t h h e a d
restraints.
They have a high position (for comfort
and safety) and a low position (for rear
visibility).
They may be removed, as follows:
pull the head restraint upwards as
far as possible,
then, press on the lug A .
When you are carrying rear pas-
sengers, never drive with the head
restraints removed. They must be
secured in place in the high position. When putting back in position,
take care not to jam the seat
belts. E n s u r e t h a t t h e y a r e c o r r e c t l y fi x e d
to the seat back before any ma-
noeuvre.
E a c h fl a p i s fi x e d t o t h e r e a r o f
the seat by two removable plastic
clips.
T o d e t a c h t h e fl a p s f r o m t h e r e a r
o f t h e s e a t b a c k , p r e s s fi r m l y d o w n
on the upper part of the two plastic
clips to release them.
To avoid risk of breakage, they dis-
engage if subjected to excessive
force.