change time Citroen C3 PICASSO RHD 2012.5 1.G Owner's Manual

Familiarisation
18
Driving safely
Going into engine STOP mode



- gear lever in position A
or M, when you
release the brake pedal,

- or
gear lever in position N
and brake pedal
released, when you change to position Aor AM,
- or when you engage reverse.
Stop & Start

The "ECO"
warning lamp comes on
in the instrument panel and the engine
automatically goes into standby with the
6-speed electronic gearbox syste
m:
- at speeds below 5 mph (8 km/h), when you
press the brake pedal or when you put thegear lever in position N .



Going into engine START mode
The "ECO"
warning lamp goes off
and the engine restarts automatically
with a 6-speed electronic gearbox
syste
m:
In some circumstances
STOP mode may not
be available; the "ECO"
warning lamp flashesfor a few seconds, then goes off. In some circumstances
STA R T m o d e m ay be
invoked automatically; the "ECO"warning lamp flashes for a few seconds, then goes off.


Deactivation / Reactivation
You can deactivate the system at any time by
pressing the "ECO OFF" button; the warninglamp in the button comes on.


Before refuelling or doing anything under the bonnet, you must switch off
the ignition using the key.


The system is reactivated automatically at every new start using the key.
13
2133
133, 13 4

20















































Eco-driving
Optimise the use of your gearbox
With a manual gearbox, move off gently, change up without waiting and drive by changing up quite soon. If your vehicle has the system, the gear efficiency indicator invites you to change up; it is displayed in theinstrument panel, follow its instructions.
With an automatic or electronic gearbox, stay in Drive "D"or Auto "A"
, according to the type of gearbox, without pressing the accelerator pedalheavily or suddenly.

Drive smoothly
Maintain a safe distance between vehicles, use engine braking rather than the brake pedal, and press the accelerator progressively. Thesepractices contribute towards a reduction in fuel consumption and CO2emissions and also helps reduce the background traffic noise.


If your vehicle has cruise control, make use of the system at speedsabove 25 mph (40 km/h) when the traffic is flowing well.



Control the use of your electrical
equipment


Before moving off, if the passenger compar tment is too warm, ventilate it by opening the windows and air vents before using the air conditioning.
Above 30 mph (50 km/h), close the windows and leave the air ventsopen.
Remember to make use of equipment that can help keep the temperature in the passenger compar tment down (sunroof and windowblinds...).
Switch off the air conditioning, unless it has automatic digital regulation,as soon as the desired temperature is attained. Switch off the demisting and defrosting controls, if not automatic. Switch off the heated seat as soon as possible.


Switch off the headlamps and front foglamps when the level of lightdoes not require their use.


Avoid running the engine before moving off, particularly in winter; your vehicle will warm up much faster while driving.


As a passenger, if you avoid connecting your multimedia devices
(film, music, video game...), you will contribute towards limiting theconsumption of electrical energy, and so of fuel.
Disconnect your por table devices before leaving the vehicle.

Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2emissions.

Monitoring
34
Total distance recorder Lighting dimmer
The total and trip distances are displayed for
thirty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked. S
ystem which measures a distance travelled
during a day or other period since it was reset
to zero by the driver.
Activation
When the lighting is on:)press the button to change the brightness
of the instruments and controls,)when the level of brightness required isreached, release the button.

Deactivation

When the lighting is off, or in day mode on
vehicles fitted with daytime running lamps,
pressing the button does not have any effect.



Tr ip distance recorder
)
With the ignition on, press the button until
zeros appear.



To conform to legislation in the country you are crossing, change the units of distance (miles or km) via theconfiguration menu.
S
ystem which measures the total distance
travelled by the vehicle during its life. System for manual adjustment of the brightness of the instruments and controls in relation to theexterior brightness.

2
Multifunction screens
35













Monochrome screen A
Controls

Displa
ys in the screen

This displays the following information:


- time,

- date,

- ambient temperature
(this flashes if there isa risk of ice),

- state of the openings (doors, boot, ...),

- audio sources (radio, CD, ...),

- trip computer (refer to the end of the section).
Warning messages or information messagesmay appear temporarily. These can be cleared
by pressing the "Back"button.


Main menu
)
Press the "MENU"
button for access to
the main menu
, then press the "  " or " " buttons to scroll through the variousmenus:
- radio-CD,
- vehicle configuration,
- options,
- displa
y settings,
- language,
- units.)
Press the "OK"button to select the menurequired.
From the audio equipment control panel, youcan: )
press the "MENU"
button for access to themain menu
, )
press the " 
" or " " buttons to scroll
through the items on the screen, ) press the "MODE"
button to change the
permanent application (trip computer, audiosource, ...),) press the "  " or " " buttons to change asetting value,)
press the "OK"button to confirm,or )
press the "Back"button to abandon the
operation in progress.



Radio-CD
With the audio equipment switched on, once
the "Radio-CD" menu has been selected youcan activate or deactivate the functions linkedwith use of the radio (RDS, REG) or the CD(introscan, shuffle, CD repeat).
For more information on the "Radio- CD"
application, refer to the "Audio s
ystem" section.

Multifunction screens
36

Display settings
Once the "Display settings" menu has been selected,you can gain access to the following settings:



- year,

- month,

- day,

- hour,

- minutes,

-
12 or 24 hour mode.


Setting the date and time
)Press the MENUbutton. )Select "Display adjust" using the "
" or ""
button.)Press OK
to confirm the selection.)Select the "Year" function using the " " or
"
" button.)Press OK
to confirm the selection.)Define the desired value, using the " " or
" " buttons. )Press OK
to confirm the selection.)Repeat the procedure for the "Month",
"Day", "Hours", and "Minutes" functions.
) Once you have selected a setting, press
the "  " or " 
" buttons to change its value.
)
Press the "  " or " " buttons to switch
respectively to the previous or next setting.) Press the "OK"
button to record the change and return to the normal display or
press the "Back"button to cancel.
Options
Once the "Options" menu has been selected, you can star t diagnostics of the status of the equipment (active, not active, faulty).
Vehicle confi guration
Once the "Vehicle Configuration" menu hasbeen selected, you can activate or deactivate
the following equipment:
- wiper linked with reverse gear (refer to the"Visibility" section),
- "guide-me-home" lighting (refer to the "Visibility" section).

2
Multifunction screens
39
Options
Once the "Options" menu has been selected, you can star t diagnostics of the status of the
equipment (active, not active, faulty).
Language
Once the "Language" menu has been
selected, you can change the language used
by the display (Français, Italiano, Nederlands,
Portugues, Portugues-Brasil, Deutsch, English,
Espanol).

Units
Once the "Units" menu has been selected, you can change the units of the followingparameters:


- temperature (°C or °F),

- fuel consumption (l/100 km, mpg or km/l).
The chosen language will also be usedin the eMyWay satellite navigationcolour screen.
For safety reasons, configuration of the multifunction screen by the driver mustonly be done when stationary.

Once the fuel consumption unit has been changed to l/100 km or km/l, the information relating to speed anddistance also changes to kilometres.

Vehicle confi guration
Once the "Vehicle configuration" menu has
been selected, you can activate or deactivate
the following systems:


- wiper linked with reverse gear (refer to the
"Visibility" section),

- "guide-me-home" lighting (refer to the
"Visibility" section),

- daytime lighting (refer to the "Visibility" section).

2
Multifunction screens
41
This displays the following information:


- time,

- date,

- ambient temperature (this flashes if there isa risk of ice),

- state of the openings (doors, boot, etc.),

- audio sources (radio, CD, USB port, etc.),

- trip computer (refer to the end of the section).
Warnin
g messages or information messagesmay appear temporarily. These can be clearedby pressing the "Back"button.
From the audio system control panel, you can: )
press the "MENU"
button to gain access to
the main menu,)
press the " 
" or " " buttons to scroll
through the items on the screen, ) press the "MODE"
button to change the
permanent application (trip computer, audiosource, ...),) press the " 
" or "
" buttons to change a
setting value,)
press the "OK"button to confirm,
or ) press the "Back"button to abandon the
operation in progress.



Main menu
)
Press the "MENU"
button to gain access to
the main menu:
- audio functions,
- the trip computer
(refer to the end of thesection),
- personalisation-configuration,
- telephone (hands-free kit). )
Press the "  " or "  " buttons to select themenu required, then confirm by pressing
the "OK"
button.












Monochrome screen C
Controls
"Au d i o f u n c t i o n s"
menu

With the audio equipment switched on, once
this menu has been selected you can activate or deactivate the functions linked with useof the radio (RDS, REG, RadioText), the CD (introscan, shuffle, CD repeat) or the MP3
pla
yer (USB por t).
For more information on the "Audio functions"
application, refer to the Audio systems par t of
the "Audio and telematics" section.


Displays in the screen

2
Multifunction screens
43

Display confi guration
Once this menu has been selected, you can
gain access to the following settings:


- brightness-video setting,

- date and time setting,

- selection of the units.
Example: setting of the duration of the "guide-me-home" lighting
)Press the "  " or "  " buttons, then the "OK"button to select the menu required.
)Press the " 
" or " 
" buttons, then the "OK"button to select the "Guide-me-homeheadlamps" line.
)
Press the " " or " " buttons to set the
value required (15, 30 or 60 seconds),
then press the "OK"button to confirm.
) Press the "
" or "" buttons, then the"OK"
button to select the "OK"box andconfirm or press the "Return"
button to cancel.
Once the fuel consumption unit has been changed to l/100 km or km/l, the information relating to speed anddistance also changes to kilometres.
Settin
g the date and time) Select the "Date and time adjustment"
functions using the " " or "
" buttons. )
Press "OK
" to confirm the selection.)
Adjust the settings one by one using the " " or "
" button then confirm with the"OK" button. )
Then select "OK
" in the screen andconfirm.

2
Multifunction screens
47





Tr ip computer, a few definitions


When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
Range
(miles or km)The distance which can still be
travelled with the fuel remainingin the tank. Related to theaverage fuel consumption over
the last few miles (kilometres)travelled.


Current fuel consumption
(mpg or l/100 km or km/l)
Calculated over the last few seconds.


Average fuel consumption
(mpg or l/100 km or km/l)
Calculated since the last trip
computer reset.


Distance travelled
(miles or km)
Calculated since the last tripcomputer reset.
Average speed
(mph or km/h)Calculated since the last trip computer reset.
Distance remaining todestination
(miles or km)This is the distance remaining to be
travelled to the final destination. It
is either calculated instantly by the
navigation system, if guidance isactivated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.

Stop & Start time counter
(minutes / seconds or hours / minutes)
If your vehicle is fitted with Stop & Star t, a time counter calculates the
time spent in STOP mode during a journey.
It resets to zero ever
y time theignition is switched on with the key.

If dashes are displayed continuouslywhile driving in place of the digits, contact a CITROËN dealer or aqualified workshop.


This value may vary following a changein the style of driving or the relief,resulting in a significant change in thecurrent fuel consumption.
This function is only displayed from 20 mph (30 km/h).

Comfort
56








Scented air freshener System permitting the diffusion of a fragrance in the passenger compar tment in accordance with your requirements, by means of the adjustment dial and the various fragrance car tridges available.

Fitting the cartridge
)Remove the cartridge from the sealing case. )Install the car tridge (flower at top right).
)Press the dial and turn it a quarter of a turnclockwise.

Thi
s dial is located on the dashboard or in the
upper glove box.
It allows you to adjust the intensity of diffusion
of the fragrance.)Turn the dial to the right to permit diffusion
of the fragrance.)Turn the dial to the left to stop diffusion of
the
fragrance.

Fragrance cartridge


Removing the cartridge
)Press the dial and turn it a quarter of a turnanti-clockwise. )Remove the cartridge.)Refit its sealing case.

As a safety precaution, do not carry out any action on the car tridge whiledriving. Do not dismantle the car tridges.Do not attempt to refill the fragrancediffuser or the cartridges.
Avoid all contact with the skin and eyes.Keep out of reach of children and animals.
Do not discard the original cartridge as this ser ves as a plug when no fragrance car tridge is in use. In order to preser ve the ser vice life of thecartridge, turn the dial to the left when you no longer wish to diffuse the fragrance in the passenger compartment.

Leave the central vents open.
The intensity of diffusion of the fragrance may depend on the ventilationor air conditioning settings.
Adjustment dial
This car tridge can be removed easily.
You can change it at any time and store it in the
sealed case which keeps it closed once it has been opened.
You can obtain different fragrance car tridges
from a CITROËN dealer or a qualified
workshop.