warning Citroen C3 PICASSO RHD 2013 1.G Owner's Guide

Safety
116

Deactivation

In exceptional conditions (starting a vehicle
which is bogged down, stuck in snow, on soft ground...), it may be advisable to deactivate the
ASR and ESP systems, so that the wheels can
move freely and regain grip.) Press the "ESP OFF"
button, located in
the centre of the dashboard.
If this warning lamp comes on
in the instrument panel and the
indicator lamp on the button comes
on
, this indicates that the ASR and
ESP systems are deactivated.

Reactivation

These systems are reactivated automatically each time the ignition is switched back on or
from 30 mph (50 km/h).) Press the "ESP OFF"
button again to
react
ivate them manually.

Operating fault

If this warning lamp comes on,
accompanied by an audible signal
and a messa
ge in the multifunction
screen, this indicates a malfunction
of these s
ystems.














Trajectory control systems
The anti-slip regulation (also known as Traction Control) optimises traction to prevent skidding
of the wheels, by acting on the brakes of the
driving wheels and on the engine.
The electronic stabilit
y programme acts on the
brake of one or more wheels and on the engine to
keep the vehicle on the trajectory required by the
driver, within the limits of the laws of physics.
Anti-slip regulation (ASR)
and electronic stability
programme (ESP)

This is indicated by flashing
of this warning lamp in the
instrument panel.

Activation
These systems are activated automatically each time the vehicle is started.
They come into operation in the event of a grip
or trajectory problem.
The ESP/ASR systems offer exceptionalsafety in normal driving, but this should not encourage the driver to take extra risks or drive at high speed.
The correct operation of thesesystems depends on obser vation of the manufacturer's recommendations regarding wheels (tyres and rims), braking components, electroniccomponents and assembly and repair procedures.
After an impact, have these systems checked by a CITROËN dealer or a qualified workshop.
Have it checked b
y a CITROËN dealer or a qualified workshop.

8
Safety
117

Seat belt not fastened / unfastened warning lamp Fastenin
g
) Pull the strap, then inser t the tongue in thebuckle. )
Check that the seat belt is fastened correctly by pulling the strap.



Height adjustment
)
To lower the attachment point, squeeze the control A
and slide it downwards.)
To raise the attachment point, slide thecontrol A
upwards.
When the ignition is switched on, this warning lamp comes on, either on theinstrument panel or on the seat belt andpassenger's front airbag warning lamp
display, if the driver and/or the frontpassenger has not fastened their seat belt.
Unfastening
) Press the red button on the buckle. )
Guide the seat belt as it rolls up.


Seat belts


Front seat belts


The front seat belts are fitted with apretensioning and force limiting system.
This s
ystem improves safety in the frontseats in the event of a front or side impact.
Depending on the severity of the impact, thepretensioning system instantly tightens the seat
belts against the body of the occupants.
The pretensioning seat belts are active when
the ignition is on.
The
force limiter reduces the pressure of the seat belt on the chest of the occupant, so
improving their protection.
From approximately 12 mph (20 km/h) this warninglamp flashes for two minutes accompanied by an audible signal. Once these two minutes have
elapsed, this warning lamp remains on until the driver and/or the front passenger fastens their seat belt.

Safety
118
Seat belt not fastened / unfastened warning lamp display
1. Front and/or rear seat belts not fastened / unfastened warning lamp. 2.
Front left seat belt warning lamp. 3.Front right seat belt warning lamp. 4.
Rear right seat belt warning lamp. 5.
Rear centre seat belt warning lamp.
6.Rear left seat belt warning lamp.


Rear seat belts

The rear seats are each fitted with a three-point
iner tia reel seat belt with force limiter (with the exception of the rear centre seat).

Locking
When the rear side side belts are not being used, you can lock them in place. To do so:)
Raise the grip Ato its maximum height.



Fastening
)
Pull the strap, then inser t the tongue in the buckle. )
Check that the seat belt is fastened correctly by pulling the strap.


Unfastening
)
Press the red button on the buckle. )
Guide the seat belt as it rolls up.

The correspondin
g warning lamp 2 or 3
comes
on in red on the seat belt and passenger's front airbag warning lamp display if the seat belt isnot fastened or is unfastened.



Seat belt unfastened warninglamp

This warning lamp comes on,either on the instrument panel or
on the seat belt and passenger's
front airbag warning lamp display, when one or more rear passengers unfasten their seat belt.
From approximatel
y 12 mph (20 km/h),
this warning lamp flashes for two minutes
accompanied by an audible signal of increasingvolume. Once these two minutes have elapsed,
this warning lamp remains on until the one or more rear passengers fasten their seat belt.

8
Safety
119
2 nd row rear centre seat
belt


Removal and storing
)
Press the red button on the buckle B, then on the buckle A.)
Guide the strap as it rolls up and bring the
tongue B , then A
onto the magnet of the
attachment point on the roof.
Installation
) Pull the strap and inser t the tongue A
in the left-hand buckle.)
Inser t the tongue Bin the right-hand buckle. )
Check the fastening of each buckle by
pulling the strap. Th
e seat belt for the rear centre seat of the 2 nd row is incorporated at the rear left of the roof.


Seat belt unfastened warninglamp display
When the ignition is switched on, thecorresponding warning lamps 4 , 5and 6
come
on in red for approximately 30 seconds, if the seat belt is not fastened.
When the en
gine is running or the vehicle ismoving, the corresponding warning lamp 4 , 5or 6
comes on in red, accompanied by an audiblesignal and a message on the multifunction screen, if a rear passenger has unfastened their seat belt.

Safety
120
In order to be effective, a seat belt must:


- be tightened as close to the body as possible,

- be pulled in front of you with a smooth movement, checking that it does not
twist,

- be used to restrain only one person,

- not bear any trace of cuts or fraying,

- not be converted or modified to avoid affecting its performance.

In accordance with current safety regulations, for all repairs on your vehicle, go to a qualified workshop with the skills and equipment needed, which a CITROËN dealer is able to provide.
Have your seat belts checked regularly by a CITROËN dealer or a qualified workshop, particularly if the straps show signs of damage. Clean the seat belt straps with soapywater or a textile cleaning product, sold byCITROËN dealers.
After folding or moving a seat or rear bench seat, ensure that the seat belt is positioned and reeled in correctly.


Recommendations for children

Use a suitable child seat if the passenger is less than 12 years old or shor ter than oneand a half metres.
Never use the same seat belt to secure more than one person.
Never allow a child to travel on your lap.


In the event of an impact
Depending on the nature and seriousness of the impact
, the pretensioning device maybe deployed before and independently of the airbags. Deployment of the pretensionersis accompanied by a slight discharge of harmless smoke and a noise, due to the activation of the pyrotechnic cartridge incorporated in the system.

In all cases, the airbag warning lamp comeson.
Following an impact, have the seat beltssystem checked, and if necessary replaced, by a CITROËN dealer or a qualifiedworkshop.
The driver must ensure that passengers usethe seat belts correctly and that they are allrestrained securely before setting off.
Wherever you are seated in the vehicle, always fasten your seat belt, even for shor t
journeys.
Do not interchange the seat belt buckles as they will not fulfil their role fully.
The seat belts are fitted with an inertia reel permitting automatic adjustment of the lengthof the strap to your size. The seat belt isstowed automatically when not in use.
Before and after use, ensure that the seatbelt is reeled in correctly.
The lower part of the strap must be positioned as low as possible on the pelvis.
The upper par t must be positioned in the hollow of the shoulder.
The inertia reels are fitted with an automatic locking device which comes into operation inthe event of a collision, emergency braking or if the vehicle rolls over. You can release the device by pulling firmly on the strap and releasing it so that it reels in slightly.

Safety
122

Operating fault

If this warning lamp comes on in the
instrument panel, accompanied by
an audible warnin
g and a message
in the multifunction screen, contact
a CITROËN dealer or a qualified
workshop to have the system checked. The airbags may no longer be deployed
in the event of a serious impact.

Reactivation

When you remove the rear wards-facing child
seat, turn switch 1to the "ON"
position toreactivate the airbag and so assure the safety
of your front passenger in the event of an
impact.
With the ignition on, this warning lampcomes on in the instrument panel
or in the seat belt and passenger's front airbag warning lamp displayfor approximately one minute, if thepassenger's front airbag is activated. According to version, this warning lamp comes on either in the
instrument panel or on the seat belt
and passen
ger's front airbag warninglamp display when the ignition is on
and until the airbag is reactivated. If this warnin
g lamp flashes, contact
a CITROËN dealer or a qualified
workshop. The passenger's front
airbag may no longer be deployed in
the event of a serious impact.
Deactivation
Only the passenger's front airbag can be deactivated:)with the ignition off, inser t the key in thefpassenger airbag deactivation switch 1 , )turn it to the "OFF"position,)then, remove the key keeping the switch in
this position.
To assure the safety of your child, it isimperative that the passenger's front
airbag is deactivated when you install a "rearwards-facing" child seat on thefront passenger seat. Other wise, the child would risk beingseriously injured or killed if the airbag were deployed.

If at least one of the two airbag
warning lamps come on continuously, do not install a child seat on the front passenger seat.
Have it checked by a CITROËN dealer or a qualified workshop.

8
Safety
123
Lateral airbags

Deployment

The lateral airbags are deployed unilaterally in
the event of a serious side impact applied to all
or par t of the side impact zone
B , perpendicular
to the longitudinal centreline of the vehicle on a horizontal plane and directed from the outside
towards the inside of the vehicle.
The lateral airbag inflates between the hip andshoulder of the front occupant of the vehicle
and the corresponding door trim panel.
Curtain airbags
System which protects the driver and passengers (with the exception of the rear centre passenger) in the event of a serious side impact in order to limit the risk of injury to the side of the head.
Each curtain airbag is built into the pillars and
the upper passenger compar tment area.

Operating fault
Deplo
yment

The cur tain airbag is deployed at the same
time as the corresponding lateral airbag in the event of a serious side impact applied to all or
part of the side impact zone B , perpendicular
to the longitudinal centreline of the vehicle on a
horizontal plane and directed from the outside
towards the inside of the vehicle.
The cur tain airbag inflates between the front or
rear occupant of the vehicle and the windows.
Impact detection zones
A. Front impact zone.B.
Side impact zone.

If this warning lamp comes on in the
instrument panel, accompanied by anaudible signal and a message in the
screen, contact a CITROËN dealer
or a qualified workshop to have the
system checked. The airbags may nolonger be deployed in the event of a
serious impact.
In the event of a minor impact or bump on the side of the vehicle or if the vehicle rolls over, the airbag may not be
deployed.
In the event of a rear or front collision, the airbag is not deployed.

System which protects the driver and frontpassenger in the event of a serious side impact
in order to limit the risk of in
jury to the chest,
between the hip and the shoulder.
Each lateral airba
g is fitted in the seat backrestframe, door side.

9
Driving
125





Parking brake


Applying
)Pull the parking brake lever fully up toimmobilise your vehicle.
When the vehicle is being driven, if this warning lampand the STOPwarning lamp come on, accompanied by an audible signal and a message on the
multifunction screen, this indicates that the parkingbrake is still on or has not been properly released.

Releasing
)Pull the parking brake lever gently, press
the release button then lower the lever fully.









6-speed manual
gearbox
Engaging 5th or 6th gear
) Move the lever fully to the right to engage 5th or 6th gear.



Engaging reverse gear
)
Raise the ring under the knob and move
the gear lever to the left then for wards.
When parking on a slope, direct your wheels against the pavement, apply the parking brake and engage a gear.

Only engage reverse gear when thevehicle is stationary with the engine at idle.

As a safety precaution and to facilitate starting of the engine:


- always select neutral,

- press the clutch pedal.

9
Driving
131





Hill start assist
(with the 6-speed
electronic gearbox
system)
System which holds your vehicle temporarily (approximately 2 seconds) when star ting on a slope, the time it takes to move your foot from
the brake pedal to the accelerator pedal.
This function is onl
y active when:


- the vehicle is completely stationary, with your foot on the brake pedal,

- certain conditions on a slope are met,

- with the driver’s door closed.
The hill start assist function cannot bedeactivated.On an ascendin
g slope, with the vehicle
stationar y, the vehicle is held momentarily
when
you release the brake pedal:- provided you are in automated mode(position A) or in manual mode (position AM )
on an electronic gearbox.On a descendin
g slope, with the vehicle
stationar y and reverse gear engaged, the
vehicle is held momentarily when you
release the brake pedal.

Operating fault

If a malfunction of the system occurs, these
warning lamps come on. Contact a CITROËN
dealer or a qualified workshop to have the system checked.
Do not leave the vehicle while it is being held in the hill star t assist phase. If you need to leave the vehicle withthe engine running, manually applythe parking brake then ensure that the parking brake warning lamp is on (not flashing) in the instrument panel.
Operation

Driving
132








Stop & Start The Stop & Star t system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restar ts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.
Operation
Going into engine STOP mode
The "ECO"warning lamp comes
on in the instrument panel and the
engine goes into standby:
- with the 6-speed electronic
gearbox
system, at speeds below 5 mph (8 km/h),
when you press the brake pedal or put thegear lever in position N.
A time counter calculates thesum of the periods in STOP
mode during a journey. It rests
itself to zero every time the
ignition is switched on with thekey.

Special cases: STOP mode not available
STOP mode is not invoked when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded 6 mph(10 km/h) since the last engine start usingthe key,

- the engine is needed to maintain acomfortable temperature in the passenger compartment,

- demisting is active,

- some special conditions (battery charge,
engine temperature, braking assistance,ambient temperature...) where the engine isneeded to assure control of a system.

The "ECO"warning lamp flashes for
a few seconds then goes off.
This operation is per fectly normal.
Never refuel with the engine in STOPmode; you must switch off the ignition with the key.
For your comfor t, during parkingmanoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...