light Citroen C3 RHD 2012 2.G User Guide

1
24
MONITORING
INSTRUMENT PANELS FOR PETROL - DIESEL, MANUAL, ELECTRONIC OR AUTOMATIC GEARBOXES
Panel grouping together the vehicle operation indication dials and warning lamps.
Depending on the version, the instrument panel may have permanent back-lighting.

Dials



1.
Rev counter.

Indicates the speed of rotation of the
engine (x 1 000 rpm).

2.
Vehicle speed.

Indicates the current speed of the
moving vehicle (mph or km/h).

3.
Fuel level.

Indicates the quantity of fuel remaining
in the tank.

4.
Screen.

5.
Display management button

Alternates display between range
and trip mileage recorder.
Servicing information.
Resets the selected function to zero
(trip distance recorder or service in-
dicator).

6.
Instrument panel lighting button.

Adjusts the brightness of the lighting
of the instruments and controls.
For more information, refer to the
section on the button or function
and its associated display.

A.
Speed limiter

(mph or km/h) or
Cruise control.


B.
Gear effi ciency indicator.


C.
Electronic
or
automatic gearbox
information.


D.
Range

(miles or km) or
Trip mileage recorder.


E.
Service indicator

(miles or km), then

Total mileage recorder

These two functions are displayed
successively when switching on the
ignition

F.
Engine oil level indicator

Appears a few seconds after switching
on the ignition, then disappears.


Screen

1
25
MONITORING
Indicator and warning lamps
Visual indicators informing the driver that a system is in operation (operation or
deactivation indicator lamps) or of the occurrence of a fault (warning lamp).

When the ignition is switched on
Certain warning lamps come on for a few seconds when the vehicle's ignition is
switched on.
When the engine is started, these same warning lamps should go off.
If they remain on, before moving off, refer to the information on the warning lamp
concerned.

Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the corresponding
system has come into operation.
The warning lamps may come
on continuously (fi xed) or fl ash.
Certain warning lamps may
come on in two different modes.
Only by relating the type of illumi-
nation to the operating status of
the vehicle can it be ascertained
whether the situation is normal
or whether a fault has occurred.

Associated warnings
The illumination of certain warning lamps may be accompanied by an audible
signal and a message in the multifunction screen.


Warning lamp



is on



Cause



Action/Observations






Left-hand
direction
indicato

r


fl ashing with
buzzer. The lighting stalk is pushed
down.




Right-hand
direction
indicator


fl ashing with
buzzer.

The lighting stalk is pushed up.






Sidelamps


fi xed. The lighting stalk is in the
"Sidelamps" position.



Hazard
warning lamps

fl ashing with
audible signal.

The hazard warning lamps
switch, located on the
dashboard, has been operated. The left-hand and right-hand direction indicators
and their associated indicator lamps fl ash
simultaneously.

1
MONITORING




Front
foglamps


fi xed. The front foglamps are
switched on. Turn the ring on the stalk rearwards twice to
switch off the front foglamps.




Rear
foglamps


fi xed. The rear foglamps are
switched on. Turn the ring on the stalk rearwards to switch off
the rear foglamps.




Diesel engine
pre-heating


fi xed. The ignition switch is at the
2nd position (ignition on). Wait until the warning lamp goes off before
starting.
The period of illumination of the warning lamp is
determined by the climatic conditions (up to about
thirty seconds in extreme climatic conditions).
If the engine does not start, switch the ignition off
and then on, wait until the warning lamp goes off
again, then start the engine.






Parking brake


fi xed.
The parking brake is
applied or not properly
released. Release the parking brake to switch off the
warning lamp, keeping your foot on the brake
pedal.
Observe the safety recommendations.
For further information on the parking brake, refer
to the "Driving" section.

Warning lamp



is on



Cause



Action/Observations






Dipped beam
headlamps


fi xed. The lighting stalk is in the
"Dipped beam headlamps"
position.




Main beam
headlamps


fi xed. The lighting stalk is pulled
towards you. Pull the stalk to return to dipped beam
headlamps.

1
27
MONITORING


Warning lamp



is on



Cause



Action/Observations





Stop & Start


fi xed. When the vehicle stops (red
lights, traffi c jams, ...) the
Stop & Start system has
put the engine into STOP
mode. The warning lamp goes off and the engine
restarts automatically in START mode, as soon
as you want to move off.

fl ashes for a
few seconds,
then goes off. STOP mode is temporarily
unavailable.
or
START mode is invoked
automatically. Refer to "Driving - § Stop & Start" for special
cases with STOP mode and START mode.



Passenger's
airbag
system
fi xed. The control switch, located
in the glove box, is in
the " ON
" position.
The passenger's front
airbag is activated.
In this case, do not install a
rear-facing child seat. Turn the control switch to the " OFF
" position
to deactivate the front passenger's airbag.
In this case you can install a rear-facing child
seat.



Engine
coolant
temperature


fi xed blue
. On starting the engine,
it indicates that the engine
is cold. After a few minutes driving, it swiches off to
indicate that the engine temperature is normal.
In order to protect your engine, avoid driving too
hard until the warning lamp has switched off.

1
39
MONITORING
The instrument panel remains illumi-
nated with only the vehicle speed and
cruise control or speed limiter informa-
tion, if in use.
If there is an alert or a change in a func-
tion or to a setting, the black panel mode
is interrupted.

Activation


)
With the lighting on, press the left
hand button of the instrument panel
several times to progressively re-
duce the dashboard lighting level.

)
Press the button again to reduce the
lighting to the minimum level and
switch off the interior mood lighting.

)
Press the button again to activate
the black panel.


Black panel

System allowing certain displays to be
switched off for night driving.

Activation
When the lighting is on:


)
press the button to change the
brightness of the instruments and
controls,

)
when the level of brightness required
is reached, release the button.


Deactivation
When the lighting is off, or in day mode
on vehicles fi tted with daytime running
lamps, pressing the button does not
have any effect.

System for manual adjustment of the
brightness of the instruments and con-
trols in relation to the exterior brightness.

2
44
MULTIFUNCTION SCREENS

Vehicle confi guration
Once the "Vehicle Confi guration" menu
has been selected, you can activate or
deactivate the following equipment:


- wiper linked with reverse gear (refer
to the "Visibility" section),

- guide-me-home lighting (refer to the
"Visibility" section),

- parking sensors (refer to the
"Driving" section).


Options
Once the "Options" menu has been
selected, you can start diagnostics
of the status of the equipment (active,
not active, faulty).
Display settings
Once the "Display settings" menu has
been selected, you can gain access to
the following settings:


- year,

- month,

- day,

- hour,

- minutes,

- 12 or 24 hour mode.


)
Once you have selected a setting,
press the " 
" or " 
" buttons to
change its value.

)
Press the " 
" or " 
" buttons to
switch respectively to the previous
or next setting.

)
Press the "OK"
button to save the
change and return to the normal
display or press the "ESC"
button
to cancel.

Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).

Units
Once the "Units" menu has been se-
lected, you can change the units of the
following parameters:


- temperature (°C or °F),

- fuel consumption (l/100 km, mpg or
km/l).
Once the fuel consumption units
have been set to mpg, the infor-
mation in the instrument panel
screen on speed and distance
will also be in mph and miles.
For safety reasons, confi guration
by the driver of the multifunction
screen must only be done when
stationary.

2
46
MULTIFUNCTION SCREENS

"Trip computer" menu

Once this menu has been selected, you
can consult information concerning the
status of the vehicle (warnings log, sta-
tus of functions, etc.)

Alert log
This summarises the active warning
messages, displaying them in succes-
sion on the multifunction screen.


"Personalisation-Configuration" menu


Defi ne the vehicle parameters
Once this menu has been selected, you
can activate or deactivate the following
equipment:


- wiper linked to reverse gear (refer to
the "Visibility" section),

- guide-me-home lighting and dura-
tion (see "Visibility" section),

- parking sensors (refer to the "Driving"
section).
)
In the "

Trip computer

"
menu, select
one of the following applications:




)
Press the "MENU"
button to gain
access to the general menu.

)
Press the arrows, then the "OK"
but-
ton to select the "

Trip computer

"

menu.
Once this menu has been selected, you
can gain access to the following func-
tions:


- defi ne the vehicle parameters,

- display confi guration,

- choice of language.


Status of functions
This summarises the status (active or
inactive) of the vehicle's functions.

Enter distance to destination
This allows you to enter an approximate
distance until your fi nal destination.

2
47
MULTIFUNCTION SCREENS
Example: setting of the duration of the
guide-me-home lighting


)
Press the " 
" or " 
" buttons, then
the "OK"
button to select the menu
required.

)
Press the " 
" or " 
" buttons,
then the "OK"
button to select the
"Guide-me-home headlamps" line.

)
Press the " 
" or " 
" buttons to
set the value required (15, 30 or
60 seconds), then press the "OK"

button to confi rm.
)
Press the " 
" or " 
" buttons, then
the "OK"
button to select the "OK"

box and confi rm or press the "ESC"

button to cancel.


Choice of language
Once this menu has been selected,
you can change the language used by
the display (Deutsch, English, Espanol,
Français, Italiano, Nederlands,
Portugues, Portugues-Brasil, Türkçe * ).

"Telephone" Menu

For safety reasons, confi guration
by the driver of the multifunction
screen must only be done when
stationary.

Display confi guration
Once this menu has been selected, you
can gain access to the following set-
tings:


- brightness-video setting,

- date and time setting,

- selection of units.
Once the fuel consumption units
have been changed to mpg, the
information in the screen relating to
speed and distance also changes
to mph and miles respectively. With Audio system on, once this menu
is selected you can confi gure your
Bluetooth hands-free system (pairing),
view the various telephone directories
(list of calls, services...) and manage
your calls (call, hang up, second call,
secret mode...).
For more information on the "Telephone" function, refer to the Audio system part
of the "Audio and telematics" section.


*
According to country of destination.

2
MULTIFUNCTION SCREENS

*
According to country.
System language
This menu allows you to select the lan-
guage used by the display: Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Polski, Portugues, Türkçe * .

Date and time
This menu allows you to set the date and
time, the format of the date and the for-
mat of the time (refer to the "Audio and
Telematics" section or to the specifi c
user guide given to you with the other
owner's documents).

Display
This menu allows you to set the bright-
ness of the screen, the screen colour
scheme and the colour of the map (day/
night or auto mode).
Vehicle
This menu allows you to activate or
deactivate certain driving and comfort
equipment:


- wiper linked with reverse gear (refer
to the "Visibility" section),

- guide-me-home lighting and dura-
tion (refer to the "Visibility" section),

- parking sensors (refer to the "Driving"
section).


Units
This menu allows you to select the
units: temperature (°C or °F) and fuel
consumption (km/l, l/100 or mpg).

System
This menu allows you to restore the fac-
tory confi guration, display the software
version and activate scrolling text. For safety reasons, confi gura-
tion of the multifunction screen
by the driver must only be done
when stationary.

3
52
COMFORT
HEATING/VENTILATION MANUAL AIR CONDITIONING
















The heating/ventilation or air condition-
ing systems operates with the engine
running, as well as in STOP mode with
Stop & Start.

1. Temperature adjustment

2. Air fl ow adjustment

)
Turn the dial from blue
(cold) to red (hot) to adjust
the temperature to your re-
quirements.



)
Turn the dial from position 1

to position 5
to obtain a com-
fortable air fl ow.

)
If you place the air fl ow control
in position 0
(deactivation of
the system), the temperature
is no longer maintained at a
comfortable level. However,
a slight fl ow of air, due to the
movement of the vehicle, can
still be felt.



Manual control panel
Electric control
panel Manual control
panel
Electric control
panel