light Citroen C3 RHD 2013 2.G Owner's Guide

5
Visibility
91








Interior mood lighting
Switching on

At night, the illumination of the central
dashboard storage compar tment comes
on automatically when the sidelamps areswitched on.On cer tain versions, three lamps located in the
suppor t between the roof and the automatic
da
y/night interior mirror come on as well.
Switching off
The interior mood lighting switches off automatically when the sidelamps areswitched off.
It can be switched off manually using the instrument panel lighting rheostat button. ) With the lighting on, press several times on
the left hand button of the instrument panel
to pro
gressively reduce the dashboard lighting level. ) Press again to reduce the lighting level
to the minimum and switch off the interior
mood lighting.

This comes on automatically when the boot is opened and goes off automatically when the boot is closed.




Boot lamp

The dimmed passenger compar tment lighting improves visibility in the vehicle when the light
is poor.
The lighting time varies according tothe circumstances:

- when the ignition is off, approximately ten minutes,

- in energy economy mode,approximately thirty seconds,

- when the engine is running, no limit.

6
Fittings
93








Sun visor









Glove box
)
To open the glove box, raise the handle.
It houses the front passenger airbagdeactivation switch A .
It gives access to the dashboard fusebox (see
the "Practical information - § Changing a fuse"
section).








Centre armrest Comfor t and storage system for the driver andfront passenger.
)
For access to the closed storage box, lift
the lever to open the lid.) For access to the open storage box below
the armrest, lift the complete armrest
t
owards the rear.
These can be used for por table devices (mobile
phone, MP3 player...) which can be connected
to the USB por t / auxiliary socket or chargedfrom the 12 V socket in the centre console.

Version with Zenith windscreen

Refer to the "Familiarisation - Zenith
windscreen" section.
Version without Zenith windscreen

The sun visors are fitted with a cour tesy mirror,
with concealing flap for the driver and a ticket / card holder. Component which protects a
gainst sunlight
from the front or the side.


Storage

6
Fittings
97





Rear parcel shelf


To remove the shelf: )unhook the two cords, )raise the shelf slightly, then unclip it on each side.







Hooks
The hooks can be used to hold shopping bags.






Storage box
)
Raise the boot carpet by pulling the strap
upwards to gain access to the storage box.
This has areas for storing a temporary puncture
repair kit, a box of spare bulbs, a first aid kit,
two warn
ing triangles, ...
) refit the boot floor carpet by folding itslightly in the middle.

Safety
108











Direction indicators Selection of the left or right direction indicators
to signal a change of direction of the vehicle.
)Left: lower the lighting stalk beyond thepoint of resistance.)Right: raise the lighting stalk beyond thepoint of resistance.
"Motorway" function
)Press briefly upwards or downwards,
without going beyond the point of resistance; the direction indicators will flash 3 times.







Hazard warning lamps
)
Press this button, the direction indicatorsflash.
They can operate with the ignition off.
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on
the deceleration, the hazard warning lamps come on automatically.
They switch off automatically the first time you accelerate.)You can also switch them off by pressingthe button.
A visual warnin
g by means of the direction
indicators to alert other road users to a vehiclebreakdown, towing or accident.

Safety
110

Operating fault
You must stop as soon as it is safe to do so.

In either case, contact a CITROËN dealer or aqualified workshop. If this warnin
g lamp comes on,
accompanied by an audible signaland a message in the screen, it
indicates a malfunction of the anti-lock braking system which could
result in loss of control of the vehicle
when braking.
If this warnin
g lamp comes on,
together with the STOPand ABSwarning lamps, accompanied by an
audible signal and a message in the screen, it indicates a malfunction of
the electronic brake force distribution
which could result in loss of control of
the vehicle when braking.
Emergency braking assistance
System which, in an emergency, enables you
to obtain the optimum braking pressure morequickly, thus reducing the stopping distance.

Activation

It is triggered by the speed at which the brake pedal is pressed.
The effect of this is a reduction in theresistance of the pedal and an increase in
braking efficiency.
When replacing wheels (tyres and rims), ensure that they conform to the manufacturer's recommendations.

When braking in an emergency, press firmly without releasing the pressure.

















Braking assistance systems
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and manoeuvrability of your vehicle when braking,
in par ticular on poor or slippery surfaces.
Activation
The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself felt by slight vibration of the brake pedal.
When braking in an emergency, press very firmly without releasing the pressure. Group of supplementar
y systems which helpyou to obtain optimum braking in complete safety in emergency situations:
- anti-lock braking system (ABS),
- electronic brake force distribution (EBFD),
- emergency braking assistance (EBA).

8
Safety
113
The driver must ensure that passengers usethe seat belts correctly and that they are allrestrained securely before setting off. Wherever you are seated in the vehicle, always fasten your seat belt, even for shor t
journeys.
Do not interchange the seat belt buckles asthey will not fulfil their role fully.
The seat belts are fitted with an inertia reel permitting automatic adjustment of the lengthof the strap to your size. The seat belt isstowed automatically when not in use.
Before and after use, ensure that the seatbelt is reeled in correctly.
The lower part of the strap must bepositioned as low as possible on the pelvis.
The upper par t must be positioned in the hollow of the shoulder.
The inertia reels are fitted with an automatic locking device which comes into operation inthe event of a collision, emergency braking or if the vehicle rolls over. You can releasethe device by pulling firmly on the strap and releasing it so that it reels in slightly.
Recommendations for children
Use a suitable child seat if the passenger isless than 12 years old or shorter than one and a half metres.Never use the same seat belt to secure morethan one person. Never allow a child to travel on your lap.
In order to be effective, a seat belt must:- be tightened as close to the body aspossible, - be pulled in front of you with a smoothmovement, checking that it does not
twist, - be used to restrain only one person,- not bear any trace of cuts or fraying,- not be converted or modified to avoid affecting its performance.
In accordance with current safety regulations, for all repairs on your vehicle,go to a qualified workshop with the skills andequipment needed, which a CITROËN dealer is able to provide.Have your seat belts checked regularly bya CITROËN dealer or a qualified workshop,particularly if the straps show signs of damage.Clean the seat belt straps with soapy water or a textile cleaning product, sold byCITROËN dealers. After folding or moving a seat or rear benchseat, ensure that the seat belt is positionedand reeled in correctly.
In the event of an impact
Depending on the nature and seriousnessof the impact
, the pretensioning device may be deployed before and independently of theairbags. Deployment of the pretensionersis accompanied by a slight discharge of harmless smoke and a noise, due to theactivation of the pyrotechnic cartridge incorporated in the system. In all cases, the airbag warning lamp comes on.Following an impact, have the seat belts system checked, and if necessary replaced,by a CITROËN dealer or a qualified workshop.

Safety
114
Airbags


Impact detection zones
A.
Front impact zone.
B. Side impact zone.
Front airbags

Deployment

The airbags are deployed, except thepassenger's front airbag if it is deactivated,
in the event of a serious front impact applied
to all or par t of the front impact zone A , in
the longitudinal centreline of the vehicle on a horizontal plane and directed from the front to
the rear of the vehicle.
The front airbag inflates between the head-
thorax of the front occupant of the vehicleand the dashboard to cushion their forwardmovement. S
ystem designed to maximise the safety of the
occupants (with the exception of the rear centrepassenger) in the event of violent collisions.
The airbags supplement the action of the force-
limiting seat belts (with the exception of the centre rear passenger).
If a collision occurs, the electronic detectors record and analyse the front and side impacts
sustained in the impact detection zones:
- in the case of a serious impact, the airbagsare deployed instantly and contribute
towards better protection of the occupants
of the vehicle
(with the exception of the rear centre passenger); immediately after theimpact, the airbags deflate rapidly so that
they do not hinder visibility or the exit of the
occupants,
- in the case of a minor or rear impact
or in cer tain roll-over conditions, the
airbags will not be deployed; the seat belt alone contributes towards ensuring your protection in these situations.
The airbags do not operate when the ignition is switched off. This equipment will only deploy once. If a second impact occurs (during thesame or a subsequent accident), theairbag will not be deployed again.
Deployment of the airbag(s) is
accompanied by a slight emission of smoke and a noise, due to theactivation of the pyrotechnic cartridgeincorporated in the system.This smoke is not harmful, but sensitiveindividuals may experience slight irritation. The noise of the detonation may result in a slight loss of hearing for a shor t time.

System which protects the driver and frontpassenger in the event of a serious front impact
in order to limit the risk of in
jury to the head and chest.
The driver's airbag is fitted in the centre of the steering wheel; the front passenger's airbag isfitted in the dashboard above the glove box.

Driving
126
Manual operation
)Select position M for sequentialchanging
of the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to changedown a gear.
It is onl
y possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the instrument panel.


Invalid value during manual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position Por N to place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle.

Operating fault
When the ignition is on, the lighting
o
f this warning lamp, accompanied by an audible signal and a message in the multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a CITROËN dealer or a qualified
workshop as soon as possible.
To r e d u c e fuel consumption when at a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.



There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,


- if you force the movement of the gear lever from the P
position to another position when the battery is flat.
If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the message disappears.

If the en
gine speed is too low or too high, the gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically.
The spor t and snow programmes do not
operate in manual mode.

9
Driving
127
The Stop & Star t system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.


Operation
-with a manual gearbox
, at speeds below
12 mph (20 km/h), when you put the gear lever into neutral, and you release theclutch pedal.
-
with a 5 or 6-speed electronic gearbox
, at speeds below 5 mph (8 km/h), when you press the brake pedal or put the gear lever
in position N .



Going into engine STOP mode
The "ECO"warning lamp comes
on in the instrument panel and the
engine goes into standby:
A tim
e counter calculates the sum
of the periods in STOP mode
during a journey. It rests itself
to zero every time the ignition isswitched on with the key.


Special cases: STOP mode notavailable
STOP mode is not invoked when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded 6 mph
(10 km/h) since the last engine star t using the key,

- the engine is needed to maintain acomfor table temperature in the passenger compartment,

- demisting is active,

- some special conditions (battery charge, engine temperature, braking assistance,
ambient temperature...
) where the engine isneeded to assure control of a system.
The "ECO"
warning lamp flashes for a few seconds then goes off.
This operation is perfectl
y normal.











Stop & Start
Never refuel with the engine in STOPmode; you must switch off the ignition with the key.
For your comfor t, during parking manoeuvres, STOP mode is not available for a few seconds after coming out of reverse gear.STOP mode does not affect the functionality of the vehicle, such as for example, braking, power steering...

Checks
146
Manual gearbox
The gearbox does not require anymaintenance (no oil change).
Refer to the MAINTENANCE AND
WARR ANT Y GUIDE for the details
of the level checking inter val for thiscomponent.
Automatic gearbox
The gearbox does not require anymaintenance (no oil change).
R
efer to the MAINTENANCE AND
WARR ANT Y GUIDE for details of
the level checking inter val for thiscomponent.
Parking brake
If excessive travel or a loss of effectiveness of this system isnoticed, the parking brake must bechecked, even between two ser vices.
Electronic gearbox
The gearbox does not require anymaintenance (no oil change).
Refer to the MAINTENANCE AND
WARR ANT Y GUIDE for details of thechecking inter val for this component.
















Brake pads

Brake disc wea
r
Brake wear depends on the style
of driving, par ticularly in the case
of vehicles used in town, over shor t
distances. It may be necessary to have
the condition of the brakes checked,
even between vehicle services.
For in
formation on checking brake
disc wear, contact a CITROËN dealer
or a quali
fied workshop.
















Only use products recommended by
CITROËN or products of equivalent quality and specification. In order to optimise the operationof units as impor tant as the braking system, CITROËN selects and offersvery specific products.

Unless there is a leak in the circuit, a drop in
the brake fluid level indicates that the brake
pads are worn.

Checking this system must be done by aCITROËN dealer or a qualified workshop.
After washing the vehicle, dampness,or in wintry conditions, ice, can form on the brake discs and pads: braking efficiency may be reduced. Make lightbrake applications to dry and defrost the brakes.