Filter Citroen C4 2005 2.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 188
ENGINECHECKING THE VALVE TIMING
Engine: KFU
Tools.
[1] Flywheel setting peg: 4507-TA. Toolkit 4507-T
[2] Camshaft setting peg: 4533-TA.C1
[3] Camshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Deconnect the battery.
Remove:
- The engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Turn the engine by means of the crankshaft screw.
IMPERATIVE: Never turn the engine backwards.
Suspend the engine.
Remove:
- The screws (3), the upper RH engine support (4)and the screws (5).
B1BP37JC
B1BP37KC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 188

Downloaded from www.Manualslib.com manuals search engine 190
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Tools.
[1]Flywheel setting peg: 4507-T.A
[2]Camshaft setting peg: 4533-T.AC1
[3] Camshaft setting peg: (-).0194.A
[4] Belt retaining pin: 4533-TA.D
IMPERATIVE: Respect the safety and cleanliness requirements.
Setting the timing.
Raise and support the vehicle, wheels hanging.
Disconnect the battery.
Remove the engine cover.
Raise and support the vehicle, wheels hanging.
Remove:
- The accessories drive belt (3)
(see corresponding operation).
- The crankshaft pulley, the engine cover.
- The upper timing cover (1).
- The oil filter (2).
Remove the sparking plugs to facilitate rotation of the engine.
Suspend the engine.
Remove the screws (4), the upper RH engine support (5)and the screws (6).
B1BP37QD
B1BP37RC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 190

Downloaded from www.Manualslib.com manuals search engine 197
ENGINE
CHECKING THE VALVE TIMING
Engine: NFU
Tools.
[1]Flywheel setting peg: 4507-T.A Toolkit 4507-T
[2a]Camshaft setting peg: 4533-TA.C1
[3b]Camshaft setting peg: 4533-TA.C2
IMPERATIVE: Respect the safety and cleanliness requirements.
Checking.
Disconnect the negative terminal of the battery.
Remove:
- The oil filter (1).
- Suspend the engine.
Remove:
- The engine support (2)and the upper timing cover (3).
B1BP2M7C
B1BP381C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 197

Downloaded from www.Manualslib.com manuals search engine 199
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engine: NFU
Tools.
[1]Flywheel setting peg: 4507-T.A Toolkit 4507-T
[2a]Camshaft setting peg: 4533-TA.C1
[2b]Camshaft setting peg: 4533-TA.C2
[3]Belt retaining pin: 4533-T.AD
[4]Dynamic tensioner roller pin: 4200-T.H
IMPERATIVE: Respect the safety and cleanliness requirements.
Removing.
Raise and support the vehicle, front wheels hanging
Disconnect the battery.
Remove:
- The auxiliaries drive belt (4)
(see corresponding operation).
- The crankshaft pulley (3).
- The oil filter.
Suspend the engine, using a workshop hoist.
Remove the timing cover, the engine support (1), the intermediate support and the timing cover (2).
B1BP382C
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 199

Downloaded from www.Manualslib.com manuals search engine 283
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2]Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Link tools [1]and [2] in series between the fuel high pressure pump and the fuel filter.
ESSENTIAL: Check that the tool [2] is clean.
Check the negative pressure according to the table below:
Vacuum Observations
10 ± 5 cmHgEngine driven by the starter motor
20 ± 5 cmHgEngine running under full load
60 ± 5 cmHgSupply circuit obstructed
(full tank strainer, piping, fuel filter)
B1BP2WHC
Engines: 8HX - 8HZ
XSARA
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 283

Downloaded from www.Manualslib.com manuals search engine 284
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2]Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIV: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Remove the air filter duct.
Link tool [1]in series, downstream of the injectors, between the fuel high pressure pump and the
fuel filter at «a»and «b».
WARNING: Any checking of pressure downstream of the fuel filter is prohibited.
Switch on the ignition.
Check the pressure :
Vacuum measured by the pressure gauge [2]:
Vacuum Observations
10 ± 0,5 cmHgEngine driven by the starter motor.
20 ± 0,5 cmHgEngine running under full load
60 ± 0,5 cmHgSupply circuit obstructed
(full tank strainer, piping, fuel filter)
B1CP0GFD
Engines: 9HX - 9HY - 9HZ
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 284

Downloaded from www.Manualslib.com manuals search engine 285
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mm low pressure connector: 4215-T
[2] Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Remove the air filter duct.
Link tool [1]in series, downstream of the injectors, between the fuel high pressure pump and the
fuel filter at «a»and «b».
WARNING: Any checking of pressure downstream of the fuel filter is prohibited.
Switch on the ignition.
ESSENTIAL: Check that the tool [2] is clean.
Check the negative pressure according to the table below:
Vacuum Observations
10 ± 05 cmhgEngine driven by the starter motor
20 ± 20 cmhgEngine running under full load
60 ± 05 cmhgSupply circuit obstructed
(full tank strainer, piping, fuel filter
B1BP2PHC
Engines: 9HZ - 9HY
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 285

Downloaded from www.Manualslib.com manuals search engine 286
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2]Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Link tools [1] and [2]in series between the fuel high pressure pump and the fuel filter.
ESSENTIAL: Check that the tool [2] is clean.
Normal vacuum values.
Engine driven by the starter motor: 10 ± 0,5 cmHg.
Engine running under full load: 20 ± 10 cmHg.
Abnormal vacuum values.
Supply circuit obstructed
(full tank strainer, piping, fuel filter): 60 ± 20 cmHg.
B1BP33RD
Engine: RHR
C4
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 286

Downloaded from www.Manualslib.com manuals search engine 287
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mmlow pressure connector: 4215-T
[2] Pressure gauge for testing boost pressure: 4073-T.A Toolkit 4073-T
Checks.
IMPERATIVE: Respect the safety and cleanliness specific to high pressure diesel injection
engines.
Link tools [1]and [2]in series between the fuel high pressure pump and the fuel filter.
ESSENTIAL: Check that the tool [2] is clean.
Vacuum Observations
10 ± 05 cmhgEngine driven by the starter motor
20 ± 20 cmhgEngine running under full load
60 ± 05 cmhgSupply circuit obstructed
(full tank strainer, piping, fuel filter)
B1BP2KUC
Engine: RHY
XSARA
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 287

Downloaded from www.Manualslib.com manuals search engine 288
INJECTION
CHECKS: LOW PRESSURE FUEL SUPPLY CIRCUIT
Tools.
[1] Ø 10 mm low pressure connector: 4215-T
[2] Ø 8 mmlow pressure connector: 4218-T
[3]Pressure gauge for testing boost pressure: 4073-T Kit 4073-T
Connect the tool [1]between the booster pump and the fuel filter
(white mark at "a" on the fuel
supply pipe).
Connect the tool [2]downstream of the diesel injectors, between the high pressure fuel pump and
the fuel filter
(green mark at "b" on the fuel return pipe).
WARNING: Any check of pressure downstream of the fuel filter is PROHIBITED.
Checks on pressure: static.
- Switch on ignition.
For 3 seconds
(normal functioning):
- Fuel supply pressure shown by the pressure gauge [3] = 1.8 ± 0.4 bar.
- Fuel return pressure shown by the pressure gauge [3] = 0.5 ± 0.4 bar.
B1BP1TWD
Engines: RHY - RHZ
XSARA PICASSO
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 288