kfu Citroen C4 2005 2.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 191
ENGINE
191
CHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Setting the timing (continued).
Rotate the engine by means of the crankshaft screw
(clockwise), to bring it to the pegging position.
Peg the flywheel, using tool [1].
Position the tools [2]and [3].
Remove the engine support assembly (9), the fixing
screw (8)and the lower cover (7).
Slacken the nut (11).
Fully detension the belt by moving the tensioner
roller (10).
Remove the timing belt.
IMPERATIVE: Check that the tensioner roller
turns freely
(no tight spot).
Refitting.
Position the
(new)timing belt, in the following
sequence:
- The inlet camshaft pulley, the exhaust camshaft
pulley, the guide roller, the crankshaft pulley, position
the tool [4], the coolant pump pulley, the dynamic
tensioner roller.
Remove the tools [1], [2], [3]and [4].
B1BP2MBC
B1BP2ZMC
B1CP0GLD
B1CP0GMD
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 191

Downloaded from www.Manualslib.com manuals search engine 192
ENGINECHECKING AND SETTING THE VALVE TIMING
Engine: KFU
Overtension on the belt.
Position «a»: Tensioner roller in detensionedposition.
Position «b»: Tensioner roller in normalposition.
Position «c»: Tensioner roller in overtensionposition.
Turn the tensioner roller (10), using an allen spanner at «e».
Place the index «d»in position «c», hold the belt to the maximum of the interval indicated.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
Rotate the crankshaft four turns
(normal direction of rotation).
IMPERATIVE: Never turn it backwards.
Check the timing setting by refitting the pegs [1], [2] and [3].
Remove the pegs [1], [2]and [3].
Adjusting the fitting tension of the timing belt.
Slacken the nut, holding the position of the tensioner roller, using an allen spanner at «e».
Bring the index «d»to its adjustment position at «b».
WARNING: The index «d» should not go past the notch «b». If it does, repeat the operation
to tension the timing belt.
Maintain the roller (10)in this position, using an allen spanner.
Tighten the tensioner roller fixing nut to 2,1 ± 0,2 m.daN.
IMPERATIVE: The tensioner roller should not turn during the tightening of its fixing. If it
does, repeat the operation to tension the timing belt.
Complete the refitting.
B1EP1DTC
B1EP1DUC
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 192

Downloaded from www.Manualslib.com manuals search engine ENGINE
279
C4CHECKING THE OIL PRESSURE
Petrol Diesel
Engine type KFU NFU RFJ RFN RFK 9HX 9HY 9HZ RHR
Temperature (°C) 90° 80°
Pressure (bars) 1,5 3 1,3 1,9
Rpm1000
Pressure (bars) 3 5,6 4
Rpm 2000 2000 2000
Pressure (bars) 5 6,3
Rpm 3000 3000
Pressure (bars) 43,5
Rpm 40004000
Tools (Toolkit 4103)
2279-T.Bis X X X X X X X X X
4103-T X X X X X X X X X
(-).0710.F1 X
(-).0710.B1 X
(-).1503.JXX X
4103-T.B X X
7001-T X X X X X
4202-T X X
NOTE: The oil pressure should be checked with the engine hot, after the oil level has been checked.
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 279

Downloaded from www.Manualslib.com manuals search engine 305
IGNITION
VehiclesEngine
BOSCH EYQUEM CHAMPION SAGEMElectrode gap Tightening
typesetting torque
1.4i 16V KFU VR8SE2,25 ± 0,2
1.6i 16V NFU3 ± 0,3
C4 2.0i 16V RFN RFN52HZ3A
2.0i RFJ REC9MCLX 2,7 ± 0,2
2.0i 16V RFK FR 7 ME
1.4i KFW FR 7 DE RFN 58 LZ RC 8 YLC 0,9 ± 0,05
XSARA 1.6i 16V NFU FR 7 ME RFN 58 HZ
2.0i 16V RFN FR 8 ME RFN 52 HZ REC 9 YCL 2,5 ± 0,2
1.6i90 hp
NFV RFN 58 LZ
XSARA100 hp FR 7 DE RC 8 YLC
PICASSO 1.8i 16V 6FZ
FR 8 ME RFN 52 HZ REC 9 YCL
2.0i 16V RFN
SPARKING PLUGS
Angl.-t2-page283-305-2005 9/01/06 10:18 Page 305

Downloaded from www.Manualslib.com manuals search engine 307
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engine type KFU NFU RFN RFK
Gearbox type MA5/L MA5/N BE4/5N BE4R/5S
SupplierSACHS VALEO VALEO VALEO
Mechanism/type200 MF 3850 200 CPX 3850 230 DNG 5100 230 DNG 5100
Hub discSAE 24/48-18Z 11 RX 11 R 14X 11 R 14X
Ø of lining. ext/int200/134 200/137 228.6/155 228.6/155
Quality of liningF810 DS 810 DS 810 DS 810 DS
ET3J4 TU5JP EW10J4 EW10J4S
Petrol
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 307

Downloaded from www.Manualslib.com manuals search engine 315
CLUTCH
GEARBOX
TRANSMISSION
CLUTCH SPECIFICATIONS
Engines: KFU - NFU - RFN - RFJ - RFK - 9HX - 9HY - 9HZ - RHR
NOTE:All the clutches are «push»type with hydraulic control.
NOTE:The DV6TED4and DW10BTED4engines are equipped with a double damping flywheel (DVA).
Description.
The declutch control has a declutch fork with a ball-joint on the axis.
(1)The ball-joint is screwed into the clutch casing
(2) Declutch fork
(3)Clutch casing
(4)Bearing
(5) Clutch plate
The clutch control slave cylinder(7)is fixed by two screws (6) into the exterior of the clutch casing.
B2BP047C
B2CP3FAC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 315

Downloaded from www.Manualslib.com manuals search engine 319
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(1)Gearbox fixings on engine: 4,5 ± 0,5
(2)Reverse gear switch: 2,5 ± 0,2
(3)Drain plug: 3,3 ± 0,3
(4)5th gear housing fixing: 2,2 ± 0,2
(5)Fixing of gearbox housing and clutch housing: 1,9 ± 0,2
B2CP3ZHD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 319

Downloaded from www.Manualslib.com manuals search engine 320
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(6)Clutch bearing guide screw: 1 ± 0,1
(7)Bearing retaining clip screw: 1,8 ± 0,2
Intermediate plate fixing: 5 ± 0,5
Hydraulic clutch slave cylinder fixing: 3 ± 0,3
B2CP3ZJD
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 320

Downloaded from www.Manualslib.com manuals search engine 321
CLUTCH
GEARBOX
TRANSMISSION
TIGHTENING TORQUES: MA/5 GEARBOX
Engines: KFU - NFU
Tightening torques (m.daN).
(8)Gearbox support shaft nut: 6,5 ± 0,6
(9) Screws fixing gearbox support on body: 1,9 ± 0,1
(10)Gearbox support plate nut: 2,5 ± 0,2
(11)Nut fixing gearbox support on body: 1,9 ± 0,1
(12)Nut securing rubber bush: 3 ± 0,3
B2CP3ZKC
C4
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 321

Downloaded from www.Manualslib.com manuals search engine 331
CLUTCH
GEARBOX
TRANSMISSION
MA/5 GEARBOX CONTROLS
Engines: KFU - NFU
B2CP3ZCD
Gear controls
C4
The gear selection and engagement cables have no adjustment.
NOTE:The two gear control cables cannot be separated.
(1)Gear engagement ball-joint: Ø 10 mm
(2)Gear engagement control cable
(3)Gear control lever
(4)Gear selection control cable
(5)Gear selection ball-joint: Ø 10 mm
Angl.-t2-page306-360-2005 9/01/06 10:20 Page 331