belt Citroen C4 2005 2.G Owner's Guide

Downloaded from www.Manualslib.com manuals search engine 163
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFN
Without air conditioning
Removing.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel, the plastic pins and the splash-shield.
Detension the belt (3)by turning the tensioner roller (1)by means of the
screw (2)
(clockwise).
NOTE:Screw (2)has a left hand thread.
Compress the tensioner roller (1).
Remove the auxiliaries drive belt (3).
IMPERATIVE: Check that the rollers (4) and (5) turn freely
(without play
and without tight spots).
Refitting.
Compress the tensioner roller (1).
Fit the auxiliaries drive belt (3).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly
positioned in the grooves of the various pulleys.
Complete the refitting.
Tightening torques:
- Tensioner roller screw (4) : 2 ± 0,2 m.daN.
- Guide roller screw (5) : 3,5 ± 0,,3 m.daN.
- Wheel bolts: 9 ± 1 m.daN.
B1BP23PCB1BP23QCB1BP23RC
With air conditioning
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 163

Downloaded from www.Manualslib.com manuals search engine 164
ENGINE
B1BP39AC
B1BP23RC
AUXILIARY EQUIPMENT DRIVE BELT
Engine: RFK
Tools.
[1]Detensioning lever for auxiliaries drive belt tensioner roller:
Dynamic spanner extension: FACOM SJ.214
Adaptor for socket 9x12 : FACOM J.274
Polygon socket 9x12 : 016
Removing.
Raise and support the vehicle, wheels hanging.
Remove the front RH wheel, the plastic pins and the splash-shield.
Turn the tensioner roller(1)by the screw (2)
(anti-clockwise), using tool [1]to detension the belt (3).
NOTE: Screw (2)has a left hand thread.
Remove the auxiliaries drive belt (3).
Refitting.
IMPERATIVE: Check that the rollers (4) and (5) turn freely
(without play and without tight spots).
Refitting.
Compress the tensioner roller (1), using tool [1].
Fit the auxiliaries drive belt (3).
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in the grooves of
the various pulleys.
Complete the refitting.
Tightening torques:
- Tensioner roller screw (4)tighten to: 2 ± 0,2 m.daN.
- Guide roller screw (5)tighten to: 3,5 ± 0,3 m.daN.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 164

Downloaded from www.Manualslib.com manuals search engine 165
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT
Tools.
[1] Dynamic tensioner compression lever: (-).0188.Z
[2] Peg for dynamic tensioner roller: (-).0194.F
Removing.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engine versions.
Remove:
- the front RH wheel.
- the sound insulation under the engine.
- the splash-shield.
WARNING: Mark the direction of fitting of the accessories belt if it is to be re-used.
Compress the dynamic tensioner roller (1)by acting at «a»
(clockwise), using tool [1].
Peg at «b». using tool [2].
Keep the dynamic tensioner roller (1)compressed and remove the auxiliaries drive belt.
IMPERATIVE: Check that the rollers (1) and (2) can turn freely
(without play and without
tight spots).
B1BP2VZD
Engines: 8HX - 8HZ
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 165

Downloaded from www.Manualslib.com manuals search engine 166
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Refitting.
WARNING: If the accessories belt is being re-used, respect the direction of fitting of the belt.
Refit the accessories belt.
Compress the tensioner roller (1)by acting at «a»
(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Check that the belt is correctly positioned in the grooves of the different pulleys.
Complete the refitting in the opposite direction to removal.
Engines: 8HX - 8HZ
B1BP2VZD
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 166

Downloaded from www.Manualslib.com manuals search engine 167
ENGINE
B1EP18UD
B1BP3ACD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HX - 9HY - 9HZ
Tools.
[1]Dynamic tensioner roller lever (DV6 TED4engine): (-).0194-E3
[1a]Dynamic tensioner roller lever (DV6 ATED4engine): (-).0194-E1
[1b]Lever extension (DV6 ATED4engine): (-).0194-E2
[2] Dynamic tensioner roller locking peg: (-).0194-F
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engine versions.
Markings on the dynamic tensioner roller.
«a»position «maximum wear»of the auxiliaries drive belt.
«b»Nominal position.
Removing.
WARNING: Mark the direction of fitting of the auxiliaries drive belt in the case of re-use of
the belt.
Compress the dynamic tensioner roller (1)by acting at «c»
(clockwise), using tool [1].
Peg using tool [2]at «d».
Keep the dynamic tensioner roller (1)compressed and remove the auxiliaries drive belt.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 167

Downloaded from www.Manualslib.com manuals search engine 168
ENGINE
B1EP18UD
B1BP3ACD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HX - 9HY - 9HZ
Refitting.
WARNING: Belt to be re-used, mark the direction of fitting of the belt.
Refit the auxiliaries drive belt.
Compress the tensioner roller (1)by acting at «c»
(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in the grooves
of the various pulleys.
Refit:
- The front RH wheel.
- The sound-deadening under the engine.
- Reconnect the battery.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 168

Downloaded from www.Manualslib.com manuals search engine 169
ENGINE
B1BP2Z6D
B1BP2ZCD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HZ - 9HY
Tools.
[1]Dynamic tensioner compression lever: (-).0188.Z
[2]Peg for dynamic tensioner roller: (-).0194.F
Removing.
Remove the front RH wheel, the under-engine sounddeadening and the splash-shield.
V
ehicle with air conditioning.
WARNING: Mark the direction of fitting of the accessories drive belt, if it is to be re-used.
Compress the tensioner roller(1)by acting at «a»
(clockwise), using tool [1].
Peg at «b», using tool [2].
Remove the accessories drive belt.
IMPERATIVE: Check that the rollers (1) and (2) can turn freely
(without play and without tight
spots).
Refitting.
WARNING: Belt to be re-used, mark the direction of fitting of the belt.
Refit the accessories drive belt.
Compress the tensioner roller (1)by acting at «a»
(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure the belt is correctly positioned in the grooves of the various pulleys.
Complete the refitting in the opposite order to removal.
XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 169

Downloaded from www.Manualslib.com manuals search engine 170
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Without power-assisted steering
Tool.
[1]Belt tension measuring instrument: 4122-T
Removal.
Loosen the screws (2).
Tighten the screw (1)until it is against its stop.
Remove the belt.
Refitting.
Refit the belt.
Fit the tool [1] on the belt at "d".
Tighten the screw (1)to obtain: 106 ± 10 SEEMunits.
Tighten the screws (2)to 2 m.daN.
Remove the tool [1].
B1BP1SECB1BP1SDC
Engine: WJY
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 170

Downloaded from www.Manualslib.com manuals search engine 171
ENGINE
XSARAAUXILIARY EQUIPMENT DRIVE BELT
Without power-assisted steering, with air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
Loosen the screws (1).
Tighten the screw (2)until it is against its stop.
Remove the belt.
Refitting.
Refit the belt.
Fit the tool [1] at "e".
Tighten the screw (2)to obtain: 106 ± 10 SEEMunits.
Tighten the screws (1)to 2 m.daN.
Remove the tool [1].
B1BP1SGCB1BP1SFC
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 171

Downloaded from www.Manualslib.com manuals search engine 172
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, without air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
WARNING: If the belt is to be reused, measure the tension before removal.
Loosen:
- the screw (1).
- the nut (2).
NOTE:The tensioner arm (3)must be against the alternator.
Remove the belt.
B1BP1SHD
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 172