Air Citroen C4 2005 2.G Service Manual

Downloaded from www.Manualslib.com manuals search engine 176
ENGINEXSARA - XSARA PICASSO AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
Without air conditioning
B1BP1YKD
Tools.
[1] Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mmpeg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2
[4]Dynamic tensioner compression lever: (-).0188.Z
Removing.
Re-use of belt.
WARNING: Mark the direction the belt was fiited in case of re-use of the same belt.
Compress the tensioner roller (2)by action at «a»
(in anti-clockwise direction), tool [4].
Keep the tensioner roller (2)compressed and remove the belt.
No re-use of belt.
Compress the tensioner roller (2)by action at «a»
(in anti-clockwise direction), tool [4].
Peg using tool [2]at «b».
Keep the tensioner roller (2)compressed and remove the belt.
Loosen the screw (1).
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 176

Downloaded from www.Manualslib.com manuals search engine 177
ENGINE
XSARA - XSARA PICASSO AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
Without air conditioning (continued)
Refitting.
Re-used belt.
Compress the tensioner roller (2)by action at «a»
(in anti-clockwise direction), tool [4].
Refit the belt.
WARNING: Respect the belt-fitting direction.
Remove the tool [4].
New belt.
Refit the belt.
Turn the eccentric roller (3), tool [1]
(clockwise)to free the tool [2]from
its pegging at «b».
Hold the eccentric roller (3), tool [1]and tighten the screw (1)to 4.3 m.daN.
Remove the tool [2].
Rotate the crankshaft 4 timesin the direction of rotation.
Check that it is possible to peg at «b», tool [3].
If not possible to peg, restart the adjustment.
B1BP1YMD
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 177

Downloaded from www.Manualslib.com manuals search engine 178
ENGINEXSARA - XSARA PICASSO
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
With air conditioning
B1BP1YLD
Tools.
[1]Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mmpeg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2
[4]Dynamic tensioner compression lever: (-).0188.Z
Removal.
Re-use of belt.
WARNING: Mark the direction the belt was fitted in case of re-use of the same belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Hold the tensioner roller (7) compressed and remove the belt.
No re-use of belt.
Compress the tensioner roller (7)by moving it at «c»
(in anti-clockwise direction), tool [4].
Peg using tool [2], at «d».
Loosen the screw (6).
Bring the eccentric roller (5)towards the rear.
Tighten the screw (6)by hand.
Remove the belt.
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 178

Downloaded from www.Manualslib.com manuals search engine 179
ENGINE
XSARA - XSARA PICASSO
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
With air conditioning (continued)
Refitting.
Re-used belt.
Compress the tensioner roller (7)by action at «c»
(in anti-clockwise direction), tool [4].
Refit the belt.
WARNING: Respect the direction belt was fitted.
Remove the tool [4].
New belt.
Refit the belt.
Turn the eccentric roller (5), tool[1]
(clockwise)to free the tool [2]from its pegging
at «d».
Hold the eccentric roller (5), tool [1]and tighten the screw (6)to 4.3 m.daN.
Remove the tool [2].
Rotate the crankshaft 4 timesin the direction of rotation.
Check that it is possible to peg at «d», tool [3].
If not possible to peg, restart the adjustment.
B1BP1YND
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 179

Downloaded from www.Manualslib.com manuals search engine 180
ENGINE
B1BP2J5D
AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHV - 4HY
Tools.
[1]Dynamic tensioner compression lever: (-).0188.Z.
[2]Dynamic tensioner roller retaining peg Ø 4 mm : (-).0188.Q1
Removing.
Remove the splash-shield, under-engine sound-deadening, front RH wheel.
WARNING: Mark the direction of fitting of the auxiliaries drive belt in the case of
re-use of the belt.
Compress the dynamic tensioner roller (1)by acting at «b»
(anti-clockwise), using tool [1].
Peg using tool [2]at «a».
IMPERATIVE : Check that the roller (1) turns freely
(without play and without tight
spots).
Refitting.
Refit the auxiliaries drive belt.
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in
the grooves of the various pulleys.
Compress the dynamic tensioner roller (1)by acting at «b», using tool [1].
Remove tool [2] at «a».
Complete the refitting.
JUMPER
Without air conditioning
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 180

Downloaded from www.Manualslib.com manuals search engine 184
ENGINERECOMMENDATIONS: TIMING BELT
Recommendations.
IMPERATIVE: After any repair involving removal of the timing belt, systematically replace:
- The timing belt.
- The tensioner roller fixing nut.
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 184

Downloaded from www.Manualslib.com manuals search engine 240
ENGINECHECKING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Tools.
[1]Flywheel setting peg: (-).0194.C
[2] Camshaft setting peg: (-).0194.B
[3] Crankshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel
injection (HDi) engine versions.
Checking and setting the timing.
Raise and support the vehicle, wheels hanging.
Disconnect the battery.
Uncouple:
- The fuel supply unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
- The exhaust line at the catalytic converter flexible pipe.
- Disconnect the connecteur at «a».
Remove the accessories drive belt
(see corresponding operation).
Support the engine with a roller jack equipped with a block.
Remove the four screws (5), the three screws (4)and the engine supports (3).
B1BP38TD
B1BP38UD
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 240

Downloaded from www.Manualslib.com manuals search engine 243
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HX - 9HY - 9HZ
Tools.
[1] Flywheel setting peg: (-).0194.C
[2]Camshaft setting peg: (-).0194.B
[3]Crankshaft setting peg: (-).0194.A
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure Diesel
injection (HDi) engine versions.
Checking and setting the timing.
Raise and support the vehicle, wheels hanging.
Disconnect the battery.
Uncouple:
- The fuel supply unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
- The exhaust line at the flexible pipe.
- Disconnect the connecteur at «a».
Remove the accessories drive belt
(see corresponding operation).
Support the engine with a roller jack equipped with a block.
Remove the four screws (5), the three screws (4)and the engine supports (3).
B1BP38TD
B1BP38UD
C4
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 243

Downloaded from www.Manualslib.com manuals search engine 249
ENGINE
CHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
B1BP304D
Tools.
[1] Flywheel setting peg: (-).0194.C
[2]Camshaft setting peg: (-).0194.B
[3]Crankshaft setting peg: (-).0194.A
Checking and setting the timing.
Removing.
Raise and support the vehicle, wheels hanging.
Disconnect the positive and negative terminals of the battery.
Remove:
- The front RH wheel.
- The front RH splash-shield.
- The accessories drive belt
(see corresponding operation).
Uncouple:
- The fuel supply unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
- The exhaust line
(at the flexible pipe).
Disconnect the connecter at «a».
Remove and move aside the power steering fluid reservoir (6).
Uncouple, plug and move aside the tube (2).
Support the engine with a roller jack equipped with a block.
Remove the engine supports (4)and (5).
XSARA PICASSO
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 249

Downloaded from www.Manualslib.com manuals search engine 252
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 9HZ - 9HY
Refitting.
Refit tool [1]at «b».
Remove the screw (10).
Refit:
- The upper timing cover (12).
- The lower timing cover (11).
- The accessories drive pulley (9).
- The screw (10).
Tightening torque
Screw (10)Pre-tighten to : 3 ± 0,3 m.daN.
Angular tighten : 180° ± 5°.
Remove tool [1].
Refit:
- The engine support (8), tighten to 5,5 ± 0,4 m.daN.
- The engine support (4), tighten to 6,1 ± 0,6 m.daN.
- The engine support (5), tighten to 2,5 ± 0,2 m.daN.
- The electrical harness (7).
- The power steering fluid reservoir (6).
XSARA PICASSO
Couple:
- The tube (2).
- The exhaust line, tighten the clip to 2,5 ± 0,3 m.daN.
- The fuel unions (1).
- The air/air heat exchanger inlet and outlet pipes (3).
Connect the connector at «a».
Refit:
- The accessories drive belt
(see corresponding operation).
- The front RH splash-shield (see corresponding operation).
- The front RH wheel, tighten to 9 ± 1 m.daN.
- Reconnect the positive and negative terminals of the battery.
IMPERATIVE: Perform the operations that are necessary following
a reconnection of the battery
(see corresponding operation).
Angl.-t2-page240-282-2005 9/01/06 10:16 Page 252