auxiliary battery Citroen C4 2005 2.G Workshop Manual

Downloaded from www.Manualslib.com manuals search engine 156
ENGINE
B1BP2LSC
B1BP2LTC
AUXILIARY EQUIPMENT DRIVE BELT
Engines: KFU - NFU
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument (SEEM) : 4122 -T
[3]Compression lever for dynamic tensioner: (-).0194.D
[4] Peg for dynamic tensioner roller of Ø 4 mm : (-) 0194.F
WARNING: (With or without air conditioning)
The auxiliaries drive belt cannot be re-used
with a manual tensioner roller.
The auxiliaries drive belt can be re-usedwith a dynamic tensioner roller.
Removing.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.
Remove the front RH wheel and the front RH splash-shield, using tool [1].
V
ehicle without air conditioning.Slacken bolts (2), screw (3)and the tensioning screw (1).
Push back the alternator towards the engine.
Remove the auxiliary equipment drive belt.
Refitting.
Refit the new auxiliary equipment drive belt.
Respect the following sequence: Crankshaft pinion, alternator pulley.
Position tool [2]on the belt.
Tighten the screw (1)to tension the belt to: 120 ± 4 SEEM units.
Tighten screw (3), bolts (2).
Remove tool [2].
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 156

Downloaded from www.Manualslib.com manuals search engine 168
ENGINE
B1EP18UD
B1BP3ACD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HX - 9HY - 9HZ
Refitting.
WARNING: Belt to be re-used, mark the direction of fitting of the belt.
Refit the auxiliaries drive belt.
Compress the tensioner roller (1)by acting at «c»
(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in the grooves
of the various pulleys.
Refit:
- The front RH wheel.
- The sound-deadening under the engine.
- Reconnect the battery.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 168

Downloaded from www.Manualslib.com manuals search engine 232
ENGINECHECKING AND SETTING THE VALVE TIMING
Engines: 8HX - 8HZ
B1BP2LXC
Tools.
[1] Pliers for removing plastic pegs: 7504-T
[2]Lever for detensioning the dynamic tensioner roller: (-).0194.E
[3]Engine flywheel setting peg: (-).0194.C
[4] Camshaft setting peg: (-).0194.B
[5]Crankshaft and high pressure pump setting peg: (-).0194.A
Preliminary operations.
Remove:
- The front RH wheel.
- The front RH splash-shield, using tool [1].
- The clips of the electrical harness on the upper timing cover.
- The accessories belt, using tool [2]
(see corresponding operation).
Checking the setting.
Disconnect the battery negative cable.
Remove the upper timing cover (1).
Rotate the engine using the screw (2)of the crankshaft pulley.
NOTE:The locking hole is located under the crankshaft bearing cap cover.
Undo the screw (2).
Detension the auxiliary drive belt dynamic tensioner roller, using tool [2].
XSARA
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 232