tyre pressure Citroen C4 2005 2.G Workshop Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2005, Model line: C4, Model: Citroen C4 2005 2.GPages: 462, PDF Size: 10.48 MB
Page 7 of 462
Downloaded from www.Manualslib.com manuals search engine GENERAL
1
IDENTIFICATION OF THE VEHICLE
E1AP0EWD
A- Manufacturer's name plate
A1 -Front RH chassis member = All versions except
CITROËN C4Coupé EW10J4S
(right hand drive).A2 -LH centre pillar = CITROËN C4 coupé EW10J4S(right hand drive).
B - Cold stamp
(cold stamp engraved on the bodywork).
C - AS/RP No. and RP paint code
(on the front pillar on driver's side).
D - Tyre pressures and tyre type
(on the front pillar on driver's side).
E - Serial number on bodywork.
F - Gearbox ident. reference - Factory serial no.
G - Engine legislation type - Factory serial no.
GENERAL
C4
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 1
Page 9 of 462
Downloaded from www.Manualslib.com manuals search engine GENERAL
3
IDENTIFICATION OF THE VEHICLE
E1AP08WD
A- Manufacturer's name plate (estate).
B -Chassis stamp, cold stamp.
C -Manufacturer's name plate (saloon).
D -Label:
(label affixed to the front pillar on driver's side)
- Tyre pressures.
- RP organisation no.
- Paint code.
E - Serial number (visible through the windscreen).
F -Engine legislation type - Factory serial no.
G - Gearbox ident. reference - Factory serial no.
XSARA
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 3
Page 11 of 462
Downloaded from www.Manualslib.com manuals search engine GENERALGENERAL
5
IDENTIFICATION OF THE VEHICLEXSARA PICASSO
E1AP088D
A- Chassis stamp
(cold stamp on bodywork).
B -Chassis no. reminder
(label located at bottom of windscreen right hand side).
C -Manufacturer's data plate
(located at bottom of RH central pillar).
D -Label:
(located on front LH door inner panel)
- Tyre pressures.
- Tyre identification.
- Spare wheel identification.
E -Label:
(located on fuse box cover)
- Factory code.
- A-S / RP N°.
- Paint code.
F -Gearbox identification ref.
G -Engine legislation type - Factory serial number.
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 5
Page 13 of 462
Downloaded from www.Manualslib.com manuals search engine 7
GENERAL
BERLINGO IDENTIFICATION OF THE VEHICLE
E1AP0AMD
A- Chassis stamp, cold stamp.
B - Manufacturer's vehicle plate.
C -Label
- RPO No.
- Paint colour code.
- Tyre pressures.
D -Gearbox ident. reference - Factory serial no.
E - Engine legislation type - Factory serial no.
Angl.-t2-page001-39-2005 9/01/06 10:07 Page 7
Page 367 of 462
Downloaded from www.Manualslib.com manuals search engine 361
AXLES
SUSPENSION
STEERING
AXLE GEOMETRY
Conditions for checking and adjusting
Vehicle heights at reference height
Rear height Front height
L2 L1
Tools : [1] Gauge for measuring the the wheel radius, 4 bolts: 4300-T.
Tyres inflated to correct pressures. Vehicle at reference height.
Steering rack locked at mid point
(see corresponding operation).
H1 = R1 - L1
H1 = Measurement between the measuring zone underneath the front
subframe and the ground.
R1 = Front wheel radius under load.
L1 =Distance between the wheel axis and the measuring zone underneath
the front subframe.H2 = R2 + L2
H2 = Measurement between the measuring zone underneath the rear sill
and the ground.
R2 =Rear wheel radius under load.
L2 =Distance between the wheel axis and the measuring zone underneath
the rear sill.
E1AP0F3D
C4
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 361
Page 394 of 462
Downloaded from www.Manualslib.com manuals search engine 388
AXLES
SUSPENSION
STEERING
H1 = R1 – L1 H1’ = R1 – L1’
H1 = From the front suspension arm linkage bolt axis to the ground.
R1 =Radius of the front wheel when laden.
L1 =From the centre of the wheel to the front suspension arm linkage
bolt axis.
H1' =From the front jacking point to the ground.
L1' =From the front jacking point to the radius of the front wheel when
laden.H2 = R2 - L2
H2 = From the rear axle silentblock face to the ground.
R2 =Radius of the rear wheel when laden.
L2 =From the centre of the wheel to the rear axle silentblock face.
AXLE GEOMETRY
Measurements at reference height
NOTE: To make the setting of reference height easier, it is acceptable to take the measurement from the flange of the jacking point.
WARNING: The values shown should only be used as guides. In case of doubt, check the settings at reference height
Rear heightFront height
B3CP05BCB3CP058DB3DP079C
XSARA PICASSO
Conditions for checking and adjusting: Tyres inflated to correct pressures. Vehicle at reference height. Steering rack locked at mid point(see corresponding operation).
Angl.-t2-page361-397-2005 9/01/06 10:22 Page 388