Position light Citroen C4 2008 1.G User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C4, Model: Citroen C4 2008 1.GPages: 257, PDF Size: 8.06 MB
Page 124 of 257
1 1 3
IX
D R I V I N G
To stop the function
- m o v e t h e c o n t r o l f r o m p o s i t i o n "LIM" to position 0.
- o r s t o p t h e e n g i n e .
The speed that you chose is memorised.
In the event of a malfunction, a message is displayed, accompanied by a sound signal and lighting of the S E R V I C E w a r n i n g l a m p .
C o n s u l t y o u r C I T R O Ë N d e a l e r .
A fl o o r m a t n o t r e c o m -mended by CITROËN risks sliding under the accelerator pedal, thus preventing you from pressing past the tight spot.
It will then be impossible to exit from the desired limitation, unless by acting on the steering wheel control.
The driver must still remain attentive and in complete control of the vehicle.
We advise the driver to keep their feet close to the pedals.
Note: if during speed limitation, the system cannot keep to the maximum speed (especially on a steep descent or if you accelerate too hard) the s p e e d fl a s h e s . A d a p t y o u r s p e e d a s necessary.
T h e f u n c t i o n w i l l r e - e n g a g e w h e n your speed has returned below the desired maximum.
Deactivation of the maximum speed
Press button 3.
The information "OFF" will appear on the instrument panel screen.
This action does not cancel the memorised maximum speed, which remains displayed in zone A of the instrument panel.
Temporary override of the maximum speed
You can exceed the memorised maximum speed at any time by pressing the accelerator pedal hard down past the tight spot.
During the time the limit speed is being exceeded, the displayed s p e e d fl a s h e s .
You have only to release the accelerator pedal to return below the maximum speed, thus keeping the function active.
Page 133 of 257
122
X
M A I N T E N A N C E
Protection cover
HDi 135 and 140 engines
Remove the protection cover by fi r s t u n c l i p p i n g p o i n t 1, then 3 and4 . D e t a c h p o i n t 2 by pulling towards you, then lift.
To reposition the protection cover, attach point 2 fi r s t . L o w e r t h e c o v e r , keeping it centred. Clip points 1 and4, pushing vertically and slightly rearwards. Clip point 3 pushing down vertically.
HDi engines are of a highly technical nature.
A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s which only your CITROËN Dealer can guarantee. A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s
Bleeding of water from the diesel f u e l fi l t e r
To be bled on a regular basis (at every oil change).
To evacuate the water, slacken the bleed screw or the water in diesel fuel sensor, which is located at the b a s e o f t h e fi l t e r , u n t i l w a t e r c e a s e s t o fl o w o u t .
Then retighten the bleed screw or the water in diesel fuel sensor.
DIESEL INJECTION EQUIPMENTWear of brake discs, brake pads and brake drums
The rate of wear of the brake pads depends on the use of your vehicle (urban use, frequent stops), and on your style of driving or the type of journey.
For information on checking the discs and drums for wear, contact a CITROËN dealer.
After washing the vehicle, brake progressively to dry out the brake linings.
Page 134 of 257
122
X
M A I N T E N A N C E
Protection cover
HDi 135 and 140 engines
Remove the protection cover by fi r s t u n c l i p p i n g p o i n t 1, then 3 and4 . D e t a c h p o i n t 2 by pulling towards you, then lift.
To reposition the protection cover, attach point 2 fi r s t . L o w e r t h e c o v e r , keeping it centred. Clip points 1 and4, pushing vertically and slightly rearwards. Clip point 3 pushing down vertically.
HDi engines are of a highly technical nature.
A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s which only your CITROËN Dealer can guarantee. A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s A l l m a i n t e n a n c e a n d r e p a i r s r e q u i r e s p e c i fi c q u a l i fi c a t i o n s
Bleeding of water from the diesel f u e l fi l t e r
To be bled on a regular basis (at every oil change).
To evacuate the water, slacken the bleed screw or the water in diesel fuel sensor, which is located at the b a s e o f t h e fi l t e r , u n t i l w a t e r c e a s e s t o fl o w o u t .
Then retighten the bleed screw or the water in diesel fuel sensor.
DIESEL INJECTION EQUIPMENTWear of brake discs, brake pads and brake drums
The rate of wear of the brake pads depends on the use of your vehicle (urban use, frequent stops), and on your style of driving or the type of journey.
For information on checking the discs and drums for wear, contact a CITROËN dealer.
After washing the vehicle, brake progressively to dry out the brake linings.