lock Citroen C4 2011.5 2.G User Guide

1
33
Monitoring
Screen 1Screen 2CauseSolution - ActionObservations
Fault with the "Keyless Entry andStarting" system. Contact a CITROËN dealer.
F
ault with the electronic anti-theftsystem. Switch off the ignition, then start theengine. If the problem persists, contact aCITROËN dealer.
The electronic key is not detected. Inser t the electronic key into the
housin
g located in the glove box. Remember to remove the electronickey from the housing after star ting
the vehicle.
The electronic ke
y has not been removed from the housing in the glove box. Remove the electronic ke
y from the
housing in the glove box.
The steering column is locked. Switch the ignition on and turn the
steering wheel slightly to unlock the
steering column.
The en
gine is off but the gear lever
is not in position P . P Place the gear lever in position P.P Only for vehicles fitted with a "CVT"gearbox.

34
Monitoring
Screen 1Screen 2CauseSolution - ActionObservations
The steering column has not lockedafter opening the driver's door. Lock the steering column by turning
the steering wheel slightly before leaving the vehicle.
Fault with the electrical system. Contact a CITROËN dealer or a qualified workshop.

1
35
Monitoring
Screen 1Screen 2CauseSolution - ActionObservations

Warning messages (ignition at "ON")
Fault with the electric power steering. Stop the vehicle, wait few moments
then start the engine again. If the message remains after
restarting, contact a CITROËN
dealer or a quali
fied workshop.
The batter
y for the "Keyless Entry and Starting" system is flat. Replace the battery (see "Changingthe batteries").
The electronic ke
y that you have onyour person is not recognised. Check that you have the correctelectronic key. If the message persists, contact a CITROËN dealer.
The electronic ke
y is still in the
vehicle and you have tried to lock
the doors or boot from the outside. Ensure that
you have the electronickey on your person before lockingthe vehicle.
One of the doors or the boot is not properly closed when locking the
vehicle from the outside. Close the door or the boot, then lock
the vehicle.
Fault with the "Ke
yless Entry andStarting" system. Contact a CITROËN dealer.

36
Monitoring
Screen 1Screen 2CauseSolution - ActionObservations
The brake fluid level is too low. Top up using a brake fluid listed by CITROËN. If the problem persists, contact
a CITROËN dealer or a qualified workshop.
Fault with the brakin
g system. You must stop as soon as it is safe
to do so. Have the system checked by a CITROËN dealer or a qualified workshop.
Fault with the anti-lock braking
s
ystem (ABS). Contact a CITROËN dealer or a qualified workshop. The vehicle retains conventional
braking without assistance but you
are advised to stop.
One of the doors or the boot is notproperly closed. Close the door or the boot. The opening in question is identified
in the screen.
The bonnet is not properly closed. Close the bonnet.
F
ault with the electronic anti-theft
system. Switch off the ignition then start the engine again. If the problem persists, contact aCITROËN dealer.
The driver's door is open and theignition is still on. Switch off the ignition before leavingthe vehicle.

1
41
Monitoring
Screen 1Screen 2SystemObservations





Information messages (ignition at "ON")

2WD two wheel drive system
Flashes for a few moments when the "2WD" (2 wheel drive) mode is selected usingthe transmission mode selector, for 4 wheel drive versions.
4WD four wheel drive system
Flashes for a few moments when the "4WD" (4 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
4WD LOCK four wheel drive system Flashes for a few moments when the "LOCK" (4 wheel drive) mode is selected usingthe transmission mode selector, for 4 wheel drive versions.
Active stability control (ASC)
Flashes when the stability control system (ASC) is operating.

54
Monitoring











AUDIO-CD system screen

Associated with the audio system, this provides
the following information:
- the time,
- audio system information (see "Audio and
Te l e m a t i c s ").



Setting the time


Selecting the adjustment mode

The digital clock can be set in automatic modeor in manual mode.
Select automatic modeor manual mode as follows: )Press button A"PWR" to switch on the audio system. )Access the setting mode by pressingbutton B
"TUNE" for approximately2 seconds.)Press button B"TUNE" several times to scroll through the various menus and select
the CT menu(clock time).

The order of the menus is the following:AF / CT / REG / TP-S / PT Y display language / SCV / PHONE / Functions setting mode OFF.
Manual mode
This mode permits manual setting of the timeusing the audio system buttons.
It can also be used when the "Automatic mode"
displays an inaccurate time, when the localRDS stations are broadcasting from a different
time zone. Automatic mod
e This mode permits automatic setting of thelocal time using the signal from RDS stations.
The symbol "CT"appears in the screen.

1
55
Monitoring
If no action is carried out within 10 seconds, the system will exit the "Functions setting mode" menuautomatically.
)Turn button B
"TUNE" to the left or to theright to select "CT ON"
(automatic mode)or "CT OFF"(manual mode). )After selecting the mode, you can exit the "Functions setting mode" menu by pressingbutton B
"TUNE" for approximately2 seconds.
The digital clock does not display seconds.
When the "minutes" display is set or reset to zero, the clock starts at the zero second of the minute selected.
The time setting is lost if the battery is disconnected.

Manual adjustment
)
With the ignition on or in the ACC (Accessories) position, press and hold
the CLOCK
button until the time displayflashes.)
Press the appropriate button to set the
time:
ButtonH:to set the hours The hours digits scroll when you press this button.
Button M:
to set the minutes
The minutes digits scroll when you press this button.
Button 00:to reset the minutes to zero.


- from 1 to 29 min:
rounded down to theprevious hour,

- from 30 to 59 min:
rounded up to the nexthour.)
After setting the time, press the DISPbutton; the time display stops flashing.
Set the time using the buttons as indicated below:

1
57
Monitoring

System screen
Once in the "Settings" menu, select "System" to modify the time zone, the units, or the display
language (English, Dutch, Swedish, French,
Portuguese, Italian, German, Spanish or
Danish) and adjust other settings.

Equipment screen
Once in the "Settings" menu, select
"Equipment" to activate or deactivate certain
drivin
g and comfor t systems, or to adjust settings.

"Settings" menu
On the control panel, press the SETbutton toopen the menu.
Remotecontrol:- operation of the direction indicators whenlocking and unlocking the vehicle.
Keyless Entry and Star ting system:
- operation of the direction indicators whenlocking and unlocking the vehicle,
- operation of the Keyless Entry and Starting system (only for unlocking, only for star ting,
or both).
Wi
pers:
- intermittent operation of the windscreen
wipers,
- operation of the front screenwash
associated with the wipers,
- ad
just the frequency of rear wiper
operation,
- continuous operation of the rear wiper,
- wiper linked to reverse gear.
Interior
/ exterior lighting:- sensitivity of the sensor for automatic
illumination of headlamps,
- guide-me-home lighting (activation/deactivation),
- welcome lighting (activation/deactivation),
Electric windows
:


- operating period after switching off the
ignition.
Direction indicators:

- motorway function.
Central lockin
g :


- selective unlocking.

- automatic door unlocking,

- timin
g of the automatic re-locking of the
vehicle after unlocking,

- deadlocking (activation/deactivation).
Other
s:

- automatic folding of the door mirrors,

- automatic cut of power supply to accessories.

- alarm (adjustment of sensor sensitivity,
activation/deactivation).


- operatin
g period for courtesy lamps after closing a door,

- automatic headlamp dipping (activation/deactivation),

- timin
g before automatic cour tesy lampsgo off,

- automatic lighting linked to the wipers.

58
Monitoring
The digital clock is set automatically.yThis mode enables the system to set the local
time automatically using the signal from theRDS stations. )On the control panel, press button A(SET)
to access the "Settings"
menu.
)
On the touch screen, press button B
toaccess the "System"menu.
The system settings screen is displayed.

You must deactivate automaticadjustment (RDS Auto Correct) to change the time zone and summer time settings. On each screen, you can return to theprevious screen by pressing button D"Back".
)
Press button C
to access the "Time"
menu.
1.RDS Auto Correct: Activate / deactivate automatic adjustment. 2.GMT / GMT+1 / GMT+2
Select the time zone. 3.Summer Time: Summer time On / Off.)Press button Dto confirm and return to theprevious menu.
Once this menu has been selected, you can
access the following functions:

60
Access
System which permits central unlocking or locking of the vehicle using the door lock or remotely. It is also used for the guide-me-home lighting andstarting the engine, as well as providing protection against theft.

















Remote control key
Unfolding the key
)First press this button to unfold the key.

Unlocking the vehicle


Complete unlocking using the remote control
)Press the open padlock to unlock
the vehicle.



Unlocking using the key


Unlocking is confirmed by the interior lighting which comes on for around15 seconds and the direction indicators which flash twice .
According to version, the door mirrors
unfold at the same time.
)Turn the key to the front in the driver's door
lock to unlock it.