tyre pressure Citroen C4 2012 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2012, Model line: C4, Model: Citroen C4 2012 2.GPages: 352, PDF Size: 9.82 MB
Page 20 of 352
18
FAMILIARISATION
Seat belts not fastened/
unfastened warning lamp
This warning lamp informs you if
the driver’s or front passenger’s
seat belt is not fastened (de-
pending on model), and if the
front passenger’s (depending
on model) or the second-row
passengers’ seat belts are unfastened.
The illuminated positions represent
those whose seat belts are not fas-
tened/unfastened.
Once the function has been activated,
when starting the engine, the system
automatically locks the doors once you
reach approximately 6 mph (10 km/h).
This function can be deactivated by
pressing button A
for more than two
seconds.
Tyre under-inflation detection
This function warns you if a tyre is de-
fl ated or punctured.
This system does not absolve the driver
of the need to regularly check the tyre
pressures.
The service warning lamp
comes on, and a vehicle outline
is displayed, accompanied by a
message and an audible signal.
Under-infl ation warning
The STOP
warning lamp comes
on, and a vehicle outline is dis-
played, accompanied by a mes-
sage and an audible signal.
Puncture
41
127
89
MONITORING
Automatic central locking
Instrument panel
with multifunction screen A or C
with the MyWay or NaviDrive
multifunction screen
1.
Instrument panel.
2.
Multifunction screen.
3.
Control buttons.
4.
Warning lamps display zone.
31
32
Manual central locking
You can use electrical central locking or
unlocking by pressing on button A
.
If one of the doors is open or is not
closed properly, central locking will not
work.
Page 32 of 352
30
FAMILIARISATION
Limit the causes of excess
consumption
Spread loads throughout the vehicle;
place the heaviest items in the bottom
of the boot, as close as possible to the
rear seats.
Limit the loads carried in the vehicle
and reduce wind resistance (roof bars,
roof rack, bicycle carrier, trailer...). Use
a roof box in preference.
Remove roof bars and roof racks after
use.
At the end of winter, remove snow tyres
and refi t your summer tyres.
Observe the recommendations
on maintenance
Check the tyre pressures regularly,
when cold, referring to the label in the
door aperture, driver's side.
Carry out this check in particular:
- before a long journey,
- at each change of season,
- after a long period out of use.
Don't forget the spare wheel and the
tyres on any trailer or caravan.
Have your vehicle serviced regularly (en-
gine oil, oil fi lter, air fi lter...) and observe
the schedule of operations recommended
by the manufacturer.
When refuelling, do not continue after
the 3 rd cut-off of the nozzle to avoid
any overfl ow.
At the wheel of your new vehicle,
it is only after the fi rst 1 800 miles
(3 000 kilometres) that you will see
the fuel consumption settle down to a
consistent average.
Switch off the headlamps and front
foglamps when the level of light does
not require their use.
Avoid running the engine before mov-
ing off, particularly in winter; your ve-
hicle will warm up much faster while
driving.
As a passenger, if you avoid connect-
ing your multimedia devices (fi lm, mu-
sic, video game...), you will contribute
towards limiting the consumption of
electrical energy, and so of fuel.
Disconnect your portable devices be-
fore leaving the vehicle.
Page 39 of 352
I
37
MONITORING
Warning lamps
When the engine is running or the vehicle is being driven, the illumination of one of the following warning lamps indicates
a fault which requires action on the part of the driver.
Any fault resulting in the illumination of a warning lamp must be investigated further by reading the associated message
in the multifunction screen.
If you encounter any problems, do not hesitate to contact a CITROËN dealer or a qualifi ed workshop.
Warning lamp
is on
Cause
Action/Observations
STOP
fi xed, associated
with another
warning lamp. It is associated with a
punctured tyre or the engine
coolant temperature. Stop as soon as it is safe to do so.
Park, switch off the ignition and call a
CITROËN dealer or a qualifi ed workshop.
Service
temporarily. A minor fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown in the screen, such as, for example:
- the closing of the doors, boot, rear
screen or bonnet,
- the remote control battery,
- the tyre pressures,
- saturation of the particle emission fi lter
(Diesel).
For any other faults, contact a CITROËN
dealer or a qualifi ed workshop.
fi xed. A major fault has occurred
for which there is no specifi c
warning lamp. Identify the fault by reading the message
shown in the screen and contact a
CITROËN dealer or a qualifi ed workshop.
Page 129 of 352
VIII
127
SAFETY
TYRE UNDER-INFLATION DETECTION
Sensors fi tted in each valve check
the tyre pressure during driving and
trigger a warning in the event of
malfunction (speed above 12 mph
(20 km/h)).
Under-infl ated tyre The tyre under-infl ation detection
system is an aid to driving which
does not replace the vigilance or
responsibility of the driver.
Puncture
The service warning lamp
comes on in the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction screen lo-
cating the wheel concerned.
Check the tyre pressures as soon as
possible. This check must be carried
out when the tyres are cold. The STOP
warning lamp
comes on in the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction screen lo-
cating the wheel concerned.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
tured or very defl ated tyre), and
have the tyre pressure checked as
soon as possible.
Sensor(s) not detected or faulty
The service warning lamp
comes on in the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction screen
locating the wheel or wheels which
are not detected or indicating a fault
in the system.
Have the faulty sensor(s) checked
by a CITROËN dealer or a qualifi ed
workshop. All repairs and changing of tyres
on a wheel fi tted with this system
must be carried out by a CITROËN
dealer or a qualifi ed workshop.
If, when changing a tyre, you in-
stall a wheel which is not detected
by your vehicle (example: fi tting
of snow tyres), you must have the
system reinitialised by a CITROËN
dealer or a qualifi ed workshop.
This system does not avoid the
need to have the tyre pressures
checked regularly (refer to the
"Technical data - Identifi cation
markings" section) to ensure that
the optimum dynamic performance
of the vehicle is maintained and
prevent premature wear of the
tyres, particularly in arduous driv-
ing conditions (heavy load, high
speed).
The tyre pressures must be
checked cold, at least once a
month. Remember to check the
pressure of the spare wheel.
The tyre under-infl ation detection
system may experience temporary
interference due to electro-magnetic
signals on a frequency close to that
used by the system.
This message is also displayed
when one of the wheels is away
from the vehicle (being repaired) or
when one or more wheels without a
sensor are fi tted.
The spare wheel is not fi tted with a
sensor.
Page 130 of 352
VIII
128
SAFETY
BRAKING ASSISTANCE
SYSTEMS
Group of supplementary systems
which help you to obtain optimum
braking in complete safety in emer-
gency situations:
- anti-lock braking system (ABS),
- electronic brake force distribu-
tion (EBFD),
- emergency braking assistance
(EBA).
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the
stability and manoeuvrability of your
vehicle when braking, in particular
on poor or slippery surfaces.
Activation
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
Normal operation of the ABS may
make itself felt by slight vibration of
the brake pedal.
Operating fault
When braking in an emergency,
press very fi rmly without releasing
the pressure. If this warning lamp comes
on, accompanied by an au-
dible signal and a message
in the screen, it indicates a
malfunction of the anti-lock braking
system which could result in loss of
control of the vehicle when braking.
If this warning lamp comes
on, together with the STOP
and ABS
warning lamps,
accompanied by an audible
signal and a message in the screen,
it indicates a malfunction of the elec-
tronic brake force distribution which
could result in loss of control of the
vehicle when braking.
You must stop as soon as it is
safe to do so.
In either case, contact a CITROËN
dealer or a qualifi ed workshop.
When replacing wheels (tyres and
rims), ensure that they conform to
the manufacturer's recommenda-
tions.
Emergency braking assistance
System which, in an emergency,
enables you to obtain the optimum
braking pressure more quickly, thus
reducing the stopping distance.
Activation
It is triggered by the speed at which
the brake pedal is pressed.
The effect of this is a reduction in
the resistance of the pedal and an
increase in braking effi ciency.
When braking in an emergency,
press fi rmly without releasing the
pressure.
Page 186 of 352
XI
184
PRACTICAL INFORMATION
)
Remove the compressor and
store the cartridge in the plastic
bag, supplied in the kit, to avoid
staining your vehicle with traces
of fl uid.
)
Drive immediately for approxi-
mately two miles (three kilome-
tres), at reduced speed (between
15 and 35 mph - 20 and 60 km/h),
to plug the puncture.
)
Stop to check the repair and the
pressure.
)
Connect the compressor pipe di-
rectly to the valve of the repaired
wheel.
)
Switch on the compressor by
moving the switch A
to position
"1"
until the tyre pressure reaches
2.0 bars. If this pressure has not been
reached after approximately three
minutes, the tyre cannot be re-
paired; contact a CITROËN dealer
or a qualifi ed workshop for assis-
tance.
Page 187 of 352
XI
185
PRACTICAL INFORMATION
)
Connect the compressor's elec-
tric plug to the vehicle's 12 V
socket again.
)
Start the vehicle again and leave
the engine running.
)
Adjust the pressure using the
compressor (to infl ate: switch A
in position "1"
; to defl ate:
switch A
in position "0"
and
press button B
), in accordance
with the vehicle's tyre pressure
label (located on the door aper-
ture on the driver's side), then re-
member to check that the leak is
plugged correctly (no further loss
of pressure after several miles).
)
Remove the compressor, then
store the whole kit.
)
Drive at reduced speed (50 mph
[80 km/h]).
)
Visit a CITROËN dealer or a
qualifi ed workshop as soon as
possible to have the tyre repaired
or replaced by a technician. Take care, the sealant
cartridge contains ethyl-
ene-glycol. This product is
harmful if swallowed and causes
irritation to the eyes. Keep it out of
reach of children.
The expiry date of the sealant is
indicated on the base of the car-
tridge.
The cartridge is designed for a sin-
gle use; even if only partly used, it
must be replaced.
After use, do not discard the car-
tridge into the environment, take it
to a CITROËN dealer or to an au-
thorised waste disposal site.
Do not forget to obtain a new
sealant cartridge, available from
a CITROËN dealer or a qualifi ed
workshop.
Under-inflation detection
If the vehicle is fi tted with tyre un-
der-infl ation detection, the tyre
under-infl ation warning lamp will
remain on after the wheel has been
repaired until the system is reini-
tialised by a CITROËN dealer or a
qualifi ed workshop.
Page 191 of 352
XI
189
PRACTICAL INFORMATION
Temporary use spare wheel
If your vehicle is equipped with a
spare wheel for temporary use only,
when fi tting this it is normal to ob-
serve that the wheel bolts do not
come to bear directly on the wheel
rim.
The spare wheel is secured by the
conical tapering of the wheel bolt’s
shaft.
When refi tting the original wheel, en-
sure that the wheel bolts and wash-
ers are clean and in good condition.
Fitting a wheel
)
Position the wheel with the aid of
the centring guide 3
.
)
Do up the 3 bolts by hand, then
remove the centring guide 3
.
Position the 4 th bolt.
)
Pre-tighten the wheel bolts, us-
ing the wheelbrace 4
.
)
Retract the jack 5
and disengage it.
)
Tighten the wheel bolts, using
the wheelbrace 4
.
)
Ensure that the tyre pressure is
correct.
Under-infl ation detection
Wheels with under-infl ation detection
have tyre pressure sensors. Have repairs
to them carried out by a CITROËN dealer
or a qualifi ed workshop. The spare wheel
does not have a sensor.
Security bolts (alloy wheels)
Each wheel may be equipped with
one security bolt (depending on the
country of sale).
To remove it:
)
remove its protective cover us-
ing of the tool for removing the
chrome covers 2
.
)
use the security bolt socket 6
with the wheelbrace 4
.
Spare wheel dimensions
If your spare wheel has dimensions
different from those of the standard
vehicle wheels (identifi ed by a la-
bel), it is imperative to use the spare
wheel only temporarily, to drive
with caution, not to exceed 50 mph
(80 km/h) and to have the tyre re-
paired and the standard wheel refi t-
ted as soon as possible.
Tyre pressures
These are indicated on the label
on the front left-hand door pillar
(see "Technical Data - Identifi cation
markings").
The wheel bolts are specifi c
to each type of wheel.
If new wheels are fi tted, check with
your CITROËN dealer or a qualifi ed
workshop that the wheel bolts are
compatible with the new wheels.
Make a note of the code number on
the head of the security bolt sock-
et. This will enable you to obtain a
replacement security bolt socket
from your dealer.
Page 211 of 352
XI
209
PRACTICAL INFORMATION
Towbar suitable for the attachment
of a trailer with additional lighting
and signalling.
Your vehicle is primarily designed
for transporting people and luggage,
but it may also be used for towing a
trailer.
We recommend the use of genuine
CITROËN towbars and their har-
nesses that have been tested and
approved from the design stage
of your vehicle, and that the fi t-
ting of the towbar is entrusted to
a CITROËN dealer or a qualifi ed
workshop.
If the towbar is not fi tted by a
CITROËN dealer, it is imperative
that it is fi tted in accordance with the
vehicle manufacturer's instructions.
Driving advice
Distribution of loads
)
Distribute the load in the trailer
so that the heaviest items are as
close as possible to the axle and
the nose weight approaches the
maximum permitted without ex-
ceeding it.
Air density decreases with altitude,
thus reducing engine performance.
Above 1 000 metres, the maximum
towed load must be reduced by 10 %
for every 1 000 metres of altitude.
Refer to the "Technical Data" section
for details of the weights and towed
loads which apply to your vehicle.
Side wind
)
Take into account the increased
sensitivity to side wind.
)
To lower the engine speed, re-
duce your speed.
The maximum towed load on a long
incline depends on the gradient and
the ambient temperature.
In all cases, keep a check on the
coolant temperature.
)
If the warning lamp and
the STOP
warning lamp
come on, stop the vehicle
and switch off the engine
as soon as possible.
Braking
Towing a trailer increases the brak-
ing distance.
To avoid overheating of the brakes
on a long mountain type of descent,
the use of engine braking is recom-
mended.
Tyres
)
Check the tyre pressures of the
towing vehicle and of the trailer,
observing the recommended
pressures.
Lighting
)
Check the electrical lighting and
signalling on the trailer.
The rear parking sensors will be
deactivated automatically if a gen-
uine CITROËN towbar is used.
Driving with a trailer places greater
demands on the towing vehicle and
the driver must take particular care.
Cooling
Towing a trailer on a slope increases
the temperature of the coolant.
As the fan is electrically controlled,
its cooling capacity is not dependent
on the engine speed.
Page 228 of 352
XII
226
TECHNICAL DATA
IDENTIFICATION MARKINGS
Various visible markings for identifi -
cation of the vehicle.
The vehicle type and the identifi ca-
tion number are also indicated on
the registration document.
All CITROËN original replacement
parts are available exclusively within
the dealer network.
For your safety and in order to re-
main within the terms of the war-
ranty, you are advised to use only
CITROËN replacement parts.
A. Manufacturer’s label
Located on the left-hand door centre
pillar.
1.
EU type approval number.
2.
Vehicle Identifi cation Number (VIN).
3.
Gross vehicle weight.
4.
Gross train weight.
5.
Maximum weight on front axle.
6.
Maximum weight on rear axle.
B. Vehicle Identification
Number (VIN)
Located on the bodywork and be-
hind the windscreen.
C. Paint colour code
Tyre reference
Tyre pressures
Located on the driver's door front
pillar.
Use the tyre pressures recom-
mended by CITROËN.
Check the tyre pressures regularly,
when the tyres are cold.
Never reduce the pressure of a hot
tyre.
When replacing tyres, it is essen-
tial to use the tyre sizes that are
recommended for your vehicle.